Commit 78da6c18 authored by Bob Beckett's avatar Bob Beckett
Browse files

board: ge: mx53ppd: Use DM for ethernet



Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Bob Beckett's avatarRobert Beckett <bob.beckett@collabora.com>
parent 3556562e
......@@ -98,31 +98,6 @@ int board_ehci_hcd_init(int port)
}
#endif
static void setup_iomux_fec(void)
{
static const iomux_v3_cfg_t fec_pads[] = {
NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP |
PAD_CTL_ODE),
NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
PAD_CTL_HYS | PAD_CTL_PKE),
};
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
static int clock_1GHz(void)
{
int ret;
......@@ -160,7 +135,6 @@ void ppd_gpio_init(void)
int board_early_init_f(void)
{
setup_iomux_fec();
ppd_gpio_init();
return 0;
......
......@@ -49,6 +49,9 @@ CONFIG_I2C_EEPROM=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC_IMX=y
CONFIG_MTD=y
CONFIG_PHYLIB=y
CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX5=y
......
......@@ -28,12 +28,6 @@
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
/* Eth Configs */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE FEC_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
......@@ -49,8 +43,6 @@
/* Command definition */
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
#define PPD_CONFIG_NFS \
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment