CPCI405AB (special version of esd CPCI405) board added.

board/esd/cpci405/config.mk

@@ -28,5 +28,9 @@
 ifeq ($(BOARD_REVISION),CPCI4052)
 TEXT_BASE = 0xFFFC0000
 else
+ifeq ($(BOARD_REVISION),CPCI405AB)
+TEXT_BASE = 0xFFFC0000
+else
 TEXT_BASE = 0xFFFD0000
 endif
+endif

board/esd/cpci405/cpci405.c

@@ -37,7 +37,11 @@
 const unsigned char fpgadata[] =
 {
 #ifdef CONFIG_CPCI405_VER2
-# include "fpgadata_cpci4052.c"
+# ifdef CONFIG_CPCI405AB
+#  include "fpgadata_cpci405ab.c"
+# else
+#  include "fpgadata_cpci4052.c"
+# endif
 #else
 # include "fpgadata_cpci405.c"
 #endif
@@ -74,10 +78,10 @@ int board_pre_init (void)
 	/*
 	 * First pull fpga-prg pin low, to disable fpga logic (on version 2 board)
 	 */
-	out32(IBM405GP_GPIO0_ODR, 0x00000000);        /* no open drain pins      */
-	out32(IBM405GP_GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output        */
-	out32(IBM405GP_GPIO0_OR,  CFG_FPGA_PRG);      /* set output pins to high */
-	out32(IBM405GP_GPIO0_OR, 0);                  /* pull prg low            */
+	out32(GPIO0_ODR, 0x00000000);        /* no open drain pins      */
+	out32(GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output        */
+	out32(GPIO0_OR,  CFG_FPGA_PRG);      /* set output pins to high */
+	out32(GPIO0_OR, 0);                  /* pull prg low            */
 
 	/*
 	 * Boot onboard FPGA
@@ -192,10 +196,10 @@ int cpci405_version(void)
 	 */
 	cntrl0Reg = mfdcr(cntrl0);
 	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
-	out32(IBM405GP_GPIO0_ODR, in32(IBM405GP_GPIO0_ODR) & ~0x00180000);
-	out32(IBM405GP_GPIO0_TCR, in32(IBM405GP_GPIO0_TCR) & ~0x00180000);
+	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00180000);
+	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00180000);
 	udelay(1000);                   /* wait some time before reading input */
-	value = in32(IBM405GP_GPIO0_IR) & 0x00180000;       /* get config bits */
+	value = in32(GPIO0_IR) & 0x00180000;       /* get config bits */
 
 	/*
 	 * Restore GPIO settings
@@ -505,4 +509,44 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 #endif /* CONFIG_CPCI405_VER2 */
 
+#if 0 /* test-only */
+/* ------------------------------------------------------------------------- */
+
+u8 *dhcp_vendorex_prep (u8 * e)
+{
+	char *ptr;
+
+/* DHCP vendor-class-identifier = 60 */
+	if ((ptr = getenv ("dhcp_vendor-class-identifier"))) {
+		*e++ = 60;
+		*e++ = strlen (ptr);
+		while (*ptr)
+			*e++ = *ptr++;
+	}
+/* my DHCP_CLIENT_IDENTIFIER = 61 */
+	if ((ptr = getenv ("dhcp_client_id"))) {
+		*e++ = 61;
+		*e++ = strlen (ptr);
+		while (*ptr)
+			*e++ = *ptr++;
+	}
+
+	return e;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+u8 *dhcp_vendorex_proc (u8 * popt)
+{
+	if (*popt == 61)
+		return (u8 *)-1;
+	if (*popt == 43) {
+		printf("|%s|", popt+4); /* test-only */
+		return (u8 *)-1;
+	}
+	return NULL;
+}
+
 /* ------------------------------------------------------------------------- */
+#endif /* test-only */

board/esd/cpci405/flash.c

@@ -86,11 +86,11 @@ unsigned long flash_init (void)
 	/* Re-do sizing to get full correct info */
 
 	if (size_b1) {
-		base_b1 = -size_b1;
 		if (size_b1 < (1 << 20)) {
 			/* minimum CS size on PPC405GP is 1MB !!! */
 			size_b1 = 1 << 20;
 		}
+		base_b1 = -size_b1;
 		mtdcr (ebccfga, pb0cr);
 		pbcr = mfdcr (ebccfgd);
 		mtdcr (ebccfga, pb0cr);
@@ -103,11 +103,11 @@ unsigned long flash_init (void)
 	}
 
 	if (size_b0) {
-		base_b0 = base_b1 - size_b0;
 		if (size_b0 < (1 << 20)) {
 			/* minimum CS size on PPC405GP is 1MB !!! */
 			size_b0 = 1 << 20;
 		}
+		base_b0 = base_b1 - size_b0;
 		mtdcr (ebccfga, pb1cr);
 		pbcr = mfdcr (ebccfgd);
 		mtdcr (ebccfga, pb1cr);

include/configs/CPCI405AB.h

+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_CPCI405		1	/* ...on a CPCI405 board	*/
+#define CONFIG_CPCI405_VER2     1       /* ...version 2                 */
+#define CONFIG_CPCI405AB        1       /* ...and special AB version    */
+
+#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+
+#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#if 0
+#define CONFIG_PREBOOT                                                          \
+        "crc32 f0207004 ffc 0;"                                                 \
+        "if cmp 0 f0207000 1;"                                                  \
+        "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"             \
+        "else;echo Old CRC is bad;fi"
+#endif
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+
+#define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
+
+#if 0 /* test-only */
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT |  \
+				 CONFIG_BOOTP_VENDOREX)
+#else
+#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT)
+#endif
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_JFFS2	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_EEPROM  )
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+
+#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
+#define CFG_BASE_BAUD       691200
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE      \
+        { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+         57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
+                                        /* resource configuration       */
+
+#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+
+#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
+#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
+#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
+
+#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
+#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define	CFG_ATA_BASE_ADDR	0xF0100000
+#define	CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
+#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
+#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
+#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
+#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
+#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+
+#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+
+#if 0 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
+#define CFG_ENV_SIZE		0x0ff8		/* Size of Environment vars	*/
+#define CFG_ENV_ADDR		\
+	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-(CFG_ENV_SIZE+8))	/* Env	*/
+
+#else /* Use EEPROM for environment variables */
+
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x400   /* 1024 bytes may be used for env vars*/
+                                   /* total size of a CAT24WC08 is 1024 bytes */
+#endif
+
+#define CFG_NVRAM_BASE_ADDR	0xf0200000		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		(32*1024)		/* NVRAM size		*/
+#define CFG_NVRAM_VXWORKS_OFFS	0x6900		/* Offset for VxWorks eth-addr	*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC08) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
+                                        /* have only 8kB, 16kB is save here     */
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0xFF800000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0xFFC00000	/* FLASH bank #1	*/
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0) initialization                                  */
+#define CFG_EBC_PB0AP           0x92015480
+#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1) initialization                                  */
+#define CFG_EBC_PB1AP           0x92015480
+#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (CAN0, 1) initialization                                       */
+#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_LED_ADDR            0xF0000380
+
+/* Memory Bank 3 (CompactFlash IDE) initialization                              */
+#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (NVRAM/RTC) initialization                                     */
+/*#define CFG_EBC_PB4AP           0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1     */
+#define CFG_EBC_PB4AP           0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1     */
+#define CFG_EBC_PB4CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 5 (optional Quart) initialization                                */
+#define CFG_EBC_PB5AP           0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR           0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 6 (FPGA internal) initialization                                 */
+#define CFG_EBC_PB6AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR           0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR      0xF0400000
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+/* FPGA internal regs */
+#define CFG_FPGA_MODE           0x00
+#define CFG_FPGA_STATUS         0x02
+#define CFG_FPGA_TS             0x04
+#define CFG_FPGA_TS_LOW         0x06
+#define CFG_FPGA_TS_CAP0        0x10
+#define CFG_FPGA_TS_CAP0_LOW    0x12
+#define CFG_FPGA_TS_CAP1        0x14
+#define CFG_FPGA_TS_CAP1_LOW    0x16
+#define CFG_FPGA_TS_CAP2        0x18
+#define CFG_FPGA_TS_CAP2_LOW    0x1a
+#define CFG_FPGA_TS_CAP3        0x1c
+#define CFG_FPGA_TS_CAP3_LOW    0x1e
+
+/* FPGA Mode Reg */
+#define CFG_FPGA_MODE_CF_RESET      0x0001
+#define CFG_FPGA_MODE_DUART_RESET   0x0002
+#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004     /* only set on CPCI-405 Ver 3 */
+#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
+#define CFG_FPGA_MODE_TS_IRQ_CLEAR  0x1000
+#define CFG_FPGA_MODE_TS_CLEAR      0x2000
+
+/* FPGA Status Reg */
+#define CFG_FPGA_STATUS_DIP0    0x0001
+#define CFG_FPGA_STATUS_DIP1    0x0002
+#define CFG_FPGA_STATUS_DIP2    0x0004
+#define CFG_FPGA_STATUS_FLASH   0x0008
+#define CFG_FPGA_STATUS_TS_IRQ  0x1000
+
+#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE       64*1024     /* 64kByte is enough for XC2S15  */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+
+#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
+#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */