Some cores don't support ethernet stashing at all, and some
instances have errata.  Adds 3 properties to gianfar nodes
which support stashing.  For now, just add this support to
85xx SoCs.

Signed-off-by: Andy Fleming <afleming@freescale.com>

* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.

* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.

* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

Fix some bugs:
  1. Correctly set intlv_ctl in cs_config.
  2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
  3. Set base_address and total memory for each ddr controller in memory
     controller interleaving mode.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash.  Instead we can just flush the L1 d-cache and invalidate the i-cache.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache.  This allows us to more efficient change mappings
from cache-able to cache-inhibited.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

in ft_blob_update () for both boards was an unneccessary
repetition of code, which this patch moves in a common
function for this boards.

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Each architecture has different ways of determine what regions of memory
might not be valid to get overwritten when we boot.  This provides a
hook to allow them to reserve any regions they care about.  Currently
only ppc, m68k and sparc need/use this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Sub-command can benefit from using the same table and search functions
that top level commands have.  Expose this functionality by refactoring
find_cmd() and introducing find_cmd_tbl() that sub-command processing
can call.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Heiko Schocher <hs@denx.de>

The EEprom contains some Manufacturerinformation,
which are read from u-boot at boot time, and saved
in same hush shell variables.

Signed-off-by: Heiko Schocher <hs@denx.de>

This new command shows the local variables defined in
the hush shell:

=> help showvar
showvar
    - print values of all hushshell variables
showvar name ...
    - print value of hushshell variable 'name'

Also make the set_local_var() and unset_local_var ()
no longer static, so it is possible to define local
hush shell variables at boot time. If CONFIG_HUSH_INIT_VAR
is defined, u-boot calls hush_init_var (), where
boardspecific code can define local hush shell
variables at boottime.

Signed-off-by: Heiko Schocher <hs@denx.de>

With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.

Signed-off-by: Heiko Schocher <hs@denx.de>

As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.

This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.

This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.

Maybe we should use the approach from Keymile as
the new standard?

Signed-off-by: Heiko Schocher <hs@denx.de>

This patch adds the option for a boardspecific
I2C deblocking mechanism for the soft i2c driver.

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:

soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

If I2C Bus is blocked (see doc/I2C_Edge_Conditions),
it is not possible to get out of this, until the
complete Hardware gets a reset. This new commando
calls again i2c_init (and that calls i2c_init_board
if defined), which will deblock the I2C Bus.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>

There are some more extensions, which are for both boards
and some more boards from this manufacturer will follow soon.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Stefan Roese <sr@denx.de>

Now it's used at UBI module. Of course other modules can use it.
If you want to use it, please define CONFIG_RBTREE

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Added support for CONFIG_EFI_PARTITION to ext2 commands.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>

The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table



Based on linux/fs/partitions/efi.[ch]

Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>