Now that get_device_and_partition() always calls get_partition_info()
when disk.c is compiled, we must always compile the function, rather
than ifdef it away.

The implementation must be conditional based on CONFIG_CMD_* etc., since
that's what e.g. part_dos.c uses to ifdef out get_partition_info_dos();
CONFIG_DOS_PARTITION can be enabled even without those commands being
enabled.

Technically, this change is required before Rob's "disk/part: introduce
get_device_and_partition" patch. However, at least when the compiler
optimizer is turned on, it isn't required before then in practice,
since get_device_and_partition() calls get_dev(), which is stubbed out
in disk.c under exactly the same conditions that get_partition_info()
is not compiled, and hence the compiler never generates code for the
call to the missing function. However, in my later patch "disk:
get_device_and_partition() "auto" partition and cleanup", the optimizer
doesn't succeed at this, and may attempt to reference the undefined
function.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

The LIST_arm rule included the Atmel boards twice (by virtue of
including both LIST_at91 and LIST_ARM9) and was missing all the
arm720t, arm946es, and arm1176 boards.  Change this list to use
boards_by_arch() which is less error prone.  After this change
"./MAKEALL arm" and "./MAKEALL -a arm" build the same boards.

Also fix up some missing and duplicate boards to arm, mips, and m68k.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>

Commit 86c63265 "ARM: arm1176: enable instruction cache in
arch_cpu_init()" defined arch_cpu_init() in a file that is shared across
all arm1176 SoCs. tnetv107x already implemented this function, which
caused linking to break. Move the new conflicting arch_cpu_init() into
arm1176/bcm2835/init.c so that it doesn't conflict; grep indicates this
function is usually defined at the SoC-level, not the CPU-level, at least
for ARM.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>

Signed-off-by: Tom Rini <trini@ti.com>

The following commit introduced some warnings associated with using
pci_addr_t instead of a proper 32-bit data type.

commit af778c6d
Author: Andrew Sharp <andywyse6@gmail.com>
Date:   Wed Aug 1 12:27:16 2012 +0000

    pci: fix errant data types and corresponding access functions

On some platforms pci_addr_t is defined as a 64-bit data type so its not
proper to use with pci_{read,write}_config_dword.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This makes it easier to include this header from other headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>

The new debugging shows the value of integers and addresses read
from the device tree and tidy up GPIO output.

Signed-off-by: Simon Glass <sjg@chromium.org>

This function should also be part of the GPIO API, so add it.

Signed-off-by: Simon Glass <sjg@chromium.org>

After further investigation this change is not correct and results in
get_ram_size returning incorrectly large values.  Reported first by
Gerlando Falauto.

This reverts commit b8496cce.

Signed-off-by: Tom Rini <trini@ti.com>

usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.

Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.

v2: fix typo found by Thomas Langer

v3: rebased on top of u-boot-usb/master

Signed-off-by: Lucas Stach <dev@lynxeye.de>

The "filesize" environment variable shall be read only when relevant
file is read.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Support for ext4 file system handling at DFU.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Update Makefile change for LIBS -> LIBS-y change.

Conflicts:
	Makefile

Signed-off-by: Tom Rini <trini@ti.com>

DMA buffer cache invalidation requires that buffers have cache-aligned
buffer locations and sizes. Use memalign() and ALLOC_CACHE_ALIGN_BUFFER()
to ensure this.

On Tegra at least, without this fix, the following fail commands fail in
u-boot-master/ext4, but succeeded at the branch's branch point in
u-boot/master. With this fix, the commands work again:

ext2ls mmc 0:1 /
ext2load mmc 0:1 /boot/zImage

Cc: Uma Shankar <uma.shankar@samsung.com>
Cc: Manjunatha C Achar <a.manjunatha@samsung.com>
Cc: Iqbal Shareef <iqbal.ams@samsung.com>
Cc: Hakgoo Lee <goodguy.lee@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

originally work by Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
----
The defines in arch/m68k/include/coldfire/flexbus.h are not compatible with
the 5235 processor. The registers in struct fbcs are different sizes from
those in the 5235. Also, the defines are a little different.

This is what I have so far. Comments?
----

Reformat the patch manually by Jason Jin

Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>

This patch adds a driver for Freescale Colfire Queued SPI bus.
Coded to work with 8 bits per transfer to use with SPI flash.
CPOL, CPHA, and CS_ACTIVE_HIGH can be configured.

Tested with MCF5270 which have 4 chip selects.

Activate by #define CONFIG_CF_QSPI in board config.

Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

Signed-off-by: Alison Wang <b18965@freescale.com>

This patch uses the general ffs definition to replace the
platform ffs definition.

This patch also fixes the build error by adding hweightN
definition for m5329evb and m5373evb.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>

This patch fixes the build error for MCF537x. As the NANDFLASH_SIZE is
redefined in boards.cfg, it is needed to rename NANDFLASH_SIZE into
CONFIG_NANDFLASH_SIZE in include/configs/M5373EVB.h.

Signed-off-by: Alison Wang <b18965@freescale.com>

Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:

- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>

[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

This is very useful on a modern system.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.

This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The MPC8308RDB Reference Manual states that no bits in the SPMODE
register are allowed to change while the enable (EN) bit is set.

This driver changes the character length bits (LEN) while the enable
(EN) bit is set. Clearing the EN bit while changing the LEN bits makes
the driver work correctly on MPC8308RDB.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

With:
fatls mmc 0 /dir/file
dir: regular directory
file: regular file

The previous code read the contents of file as if it were directory entries to
list. This patch refuses to list file contents as if it were a folder.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>

When variables explicitly specified on the command line are not present
in the imported env, delete them from the running env.
If the variable is also missing from the running env, issue a warning.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Change the syntax (user API) for "env default":
  -f: override write-once variables
  var... : accept individual variable(s)
  -a: all (resetting the whole env is NOT the default behavior)

Enable variable checking and make changes effective by
enabling do_apply argument to himport_r().

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>

Change hashtable so that a callback function will decide whether a
variable can be overwritten, and possibly apply the changes.

So add a new field to struct hsearch_data:

 o "apply" callback function to check whether a variable can be
    overwritten, and possibly immediately apply the changes;
    when NULL, no check is performed.

And a new argument to himport_r():
 o "do_apply": whether to call the apply callback function

NOTE: This patch does not change the current behavior.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>