Commit 0c9a66ec authored by Andreas Gruenbacher's avatar Andreas Gruenbacher
parents c2c4be28 9ca250a5

Too many changes to show.

To preserve performance only 1000 of 1000+ files are displayed.

......@@ -32,8 +32,6 @@ cpufreq-stats.txt - General description of sysfs cpufreq stats.
index.txt - File index, Mailing list and Links (this document)
intel-pstate.txt - Intel pstate cpufreq driver specific file.
pcc-cpufreq.txt - PCC cpufreq driver specific file.
......
......@@ -32,7 +32,7 @@ Example:
compatible = "st,stm32h743-rcc", "st,stm32-rcc";
reg = <0x58024400 0x400>;
#reset-cells = <1>;
#clock-cells = <2>;
#clock-cells = <1>;
clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s_ckin>;
st,syscfg = <&pwrcfg>;
......
* Altera I2C Controller
* This is Altera's synthesizable logic block I2C Controller for use
* in Altera's FPGAs.
Required properties :
- compatible : should be "altr,softip-i2c-v1.0"
- reg : Offset and length of the register set for the device
- interrupts : <IRQ> where IRQ is the interrupt number.
- clocks : phandle to input clock.
- #address-cells = <1>;
- #size-cells = <0>;
Recommended properties :
- clock-frequency : desired I2C bus clock frequency in Hz.
Optional properties :
- fifo-size : Size of the RX and TX FIFOs in bytes.
- Child nodes conforming to i2c bus binding
Example :
i2c@100080000 {
compatible = "altr,softip-i2c-v1.0";
reg = <0x00000001 0x00080000 0x00000040>;
interrupt-parent = <&intc>;
interrupts = <0 43 4>;
clocks = <&clk_0>;
clock-frequency = <100000>;
#address-cells = <1>;
#size-cells = <0>;
fifo-size = <4>;
eeprom@51 {
compatible = "atmel,24c32";
reg = <0x51>;
pagesize = <32>;
};
};
* I2C controller embedded in STMicroelectronics STM32 I2C platform
Required properties :
- compatible : Must be "st,stm32f4-i2c"
- compatible : Must be one of the following
- "st,stm32f4-i2c"
- "st,stm32f7-i2c"
- reg : Offset and length of the register set for the device
- interrupts : Must contain the interrupt id for I2C event and then the
interrupt id for I2C error.
......@@ -14,8 +16,16 @@ Required properties :
Optional properties :
- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
the default 100 kHz frequency will be used. As only Normal and Fast modes
are supported, possible values are 100000 and 400000.
the default 100 kHz frequency will be used.
For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
100000 and 400000.
For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
possible values are 100000, 400000 and 1000000.
- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
(default: 25)
- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
(default: 10)
I2C Timings are derived from these 2 values
Example :
......@@ -31,3 +41,16 @@ Example :
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
pinctrl-names = "default";
};
i2c@40005400 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x40005400 0x400>;
interrupts = <31>,
<32>;
resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
clocks = <&rcc 1 CLK_I2C1>;
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
pinctrl-names = "default";
};
* PWM vibrator device tree bindings
Registers a PWM device as vibrator. It is expected, that the vibrator's
strength increases based on the duty cycle of the enable PWM channel
(100% duty cycle meaning strongest vibration, 0% meaning no vibration).
The binding supports an optional direction PWM channel, that can be
driven at fixed duty cycle. If available this is can be used to increase
the vibration effect of some devices.
Required properties:
- compatible: should contain "pwm-vibrator"
- pwm-names: Should contain "enable" and optionally "direction"
- pwms: Should contain a PWM handle for each entry in pwm-names
Optional properties:
- vcc-supply: Phandle for the regulator supplying power
- direction-duty-cycle-ns: Duty cycle of the direction PWM channel in
nanoseconds, defaults to 50% of the channel's
period.
Example from Motorola Droid 4:
&omap4_pmx_core {
vibrator_direction_pin: pinmux_vibrator_direction_pin {
pinctrl-single,pins = <
OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */
>;
};
vibrator_enable_pin: pinmux_vibrator_enable_pin {
pinctrl-single,pins = <
OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */
>;
};
};
/ {
pwm8: dmtimer-pwm {
pinctrl-names = "default";
pinctrl-0 = <&vibrator_direction_pin>;
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
ti,timers = <&timer8>;
ti,clock-source = <0x01>;
};
pwm9: dmtimer-pwm {
pinctrl-names = "default";
pinctrl-0 = <&vibrator_enable_pin>;
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
ti,timers = <&timer9>;
ti,clock-source = <0x01>;
};
vibrator {
compatible = "pwm-vibrator";
pwms = <&pwm8 0 1000000000 0>,
<&pwm9 0 1000000000 0>;
pwm-names = "enable", "direction";
direction-duty-cycle-ns = <1000000000>;
};
};
......@@ -15,11 +15,14 @@ Required properties
compatible : Must be "ams,as3645a".
reg : The I2C address of the device. Typically 0x30.
#address-cells : 1
#size-cells : 0
Required properties of the "flash" child node
=============================================
Required properties of the flash child node (0)
===============================================
reg: 0
flash-timeout-us: Flash timeout in microseconds. The value must be in
the range [100000, 850000] and divisible by 50000.
flash-max-microamp: Maximum flash current in microamperes. Has to be
......@@ -33,20 +36,21 @@ ams,input-max-microamp: Maximum flash controller input current. The
and divisible by 50000.
Optional properties of the "flash" child node
=============================================
Optional properties of the flash child node
===========================================
label : The label of the flash LED.
Required properties of the "indicator" child node
=================================================
Required properties of the indicator child node (1)
===================================================
reg: 1
led-max-microamp: Maximum indicator current. The allowed values are
2500, 5000, 7500 and 10000.
Optional properties of the "indicator" child node
=================================================
Optional properties of the indicator child node
===============================================
label : The label of the indicator LED.
......@@ -55,16 +59,20 @@ Example
=======
as3645a@30 {
#address-cells: 1
#size-cells: 0
reg = <0x30>;
compatible = "ams,as3645a";
flash {
flash@0 {