Commit 48c926cd authored by Marco Franchi's avatar Marco Franchi Committed by Rob Herring

dt-bindings: Remove leading zeros from bindings notation

Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`

Some unnecessary changes were manually fixed.
Signed-off-by: default avatarMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: default avatarRob Herring <robh@kernel.org>
parent efb5b43a
......@@ -62,7 +62,7 @@ pmu_system_controller: system-controller@10040000 {
Example of clock consumer :
usb3503: usb3503@08 {
usb3503: usb3503@8 {
/* ... */
clock-names = "refclk";
clocks = <&pmu_system_controller 0>;
......
......@@ -71,7 +71,7 @@ Optional nodes:
- compatible: only "samsung,secure-firmware" is currently supported
- reg: address of non-secure SYSRAM used for communication with firmware
firmware@0203F000 {
firmware@203F000 {
compatible = "samsung,secure-firmware";
reg = <0x0203F000 0x1000>;
};
......@@ -33,7 +33,7 @@ Required properties:
property with the highest frequency
Example:
v2m_sysctl: sysctl@020000 {
v2m_sysctl: sysctl@20000 {
compatible = "arm,sp810", "arm,primecell";
reg = <0x020000 0x1000>;
clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
......
......@@ -37,7 +37,7 @@ Example:
compatible = "arm,vexpress-sysreg";
reg = <0x10000000 0x1000>;
v2m_led_gpios: sys_led@08 {
v2m_led_gpios: sys_led@8 {
compatible = "arm,vexpress-sysreg,sys_led";
gpio-controller;
#gpio-cells = <2>;
......
......@@ -56,7 +56,7 @@ Examples:
interrupts = <115>;
};
ahci: sata@01c18000 {
ahci: sata@1c18000 {
compatible = "allwinner,sun4i-a10-ahci";
reg = <0x01c18000 0x1000>;
interrupts = <56>;
......
......@@ -25,7 +25,7 @@ Optional properties:
Examples:
sata@02200000 {
sata@2200000 {
compatible = "fsl,imx6q-ahci";
reg = <0x02200000 0x4000>;
interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
......
......@@ -61,7 +61,7 @@ Timing property for child nodes. It is mandatory, not optional.
Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
weim: weim@021b8000 {
weim: weim@21b8000 {
compatible = "fsl,imx6q-weim";
reg = <0x021b8000 0x4000>;
clocks = <&clks 196>;
......
......@@ -28,7 +28,7 @@ which can normally be found in the datasheet.
Example:
rsb@01f03400 {
rsb@1f03400 {
compatible = "allwinner,sun8i-a23-rsb";
reg = <0x01f03400 0x400>;
interrupts = <0 39 4>;
......
......@@ -59,7 +59,7 @@ syscon: syscon@10000000 {
compatible = "syscon";
reg = <0x10000000 0x1000>;
oscclk0: osc0@0c {
oscclk0: osc0@c {
compatible = "arm,syscon-icst307";
#clock-cells = <0>;
lock-offset = <0x20>;
......
......@@ -80,7 +80,7 @@ Example 3: I2S controller node that consumes the clock generated by the clock
controller. Refer to the standard clock bindings for information
about 'clocks' and 'clock-names' property.
i2s0: i2s@03830000 {
i2s0: i2s@3830000 {
compatible = "samsung,i2s-v5";
reg = <0x03830000 0x100>;
dmas = <&pdma0 10
......
......@@ -43,7 +43,7 @@ Example: I2S controller node that consumes the clock generated by the clock
controller. Refer to the standard clock bindings for information
about 'clocks' and 'clock-names' property.
i2s0: i2s@03830000 {
i2s0: i2s@3830000 {
/* ... */
clock-names = "iis", "i2s_opclk0",
"i2s_opclk1";
......
......@@ -21,7 +21,7 @@ Required properties:
a size of 8.
- #clock-cells : from common clock binding; shall be set to 1
divider_clk: core-clock@0064 {
divider_clk: core-clock@64 {
compatible = "marvell,dove-divider-clock";
reg = <0x0064 0x8>;
#clock-cells = <1>;
......
......@@ -10,13 +10,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx1-clock.h
for the full list of i.MX1 clock IDs.
Examples:
clks: ccm@0021b000 {
clks: ccm@21b000 {
#clock-cells = <1>;
compatible = "fsl,imx1-ccm";
reg = <0x0021b000 0x1000>;
};
pwm: pwm@00208000 {
pwm: pwm@208000 {
#pwm-cells = <2>;
compatible = "fsl,imx1-pwm";
reg = <0x00208000 0x1000>;
......
......@@ -14,14 +14,14 @@ Examples:
#include <dt-bindings/clock/imx6qdl-clock.h>
clks: ccm@020c4000 {
clks: ccm@20c4000 {
compatible = "fsl,imx6q-ccm";
reg = <0x020c4000 0x4000>;
interrupts = <0 87 0x04 0 88 0x04>;
#clock-cells = <1>;
};
uart1: serial@02020000 {
uart1: serial@2020000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x02020000 0x4000>;
interrupts = <0 26 0x04>;
......
......@@ -46,7 +46,7 @@ Example:
/* ... */
Node of the MFD chip
max77686: max77686@09 {
max77686: max77686@9 {
compatible = "maxim,max77686";
interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>;
......@@ -71,7 +71,7 @@ Example:
/* ... */
Node of the MFD chip
max77802: max77802@09 {
max77802: max77802@9 {
compatible = "maxim,max77802";
interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>;
......
......@@ -42,7 +42,7 @@ Required properties:
Example:
clockgen-a@090ff000 {
clockgen-a@90ff000 {
compatible = "st,clkgen-c32";
reg = <0x90ff000 0x1000>;
......
......@@ -36,7 +36,7 @@ For the PRCM CCUs on A83T/H3/A64, two more clocks are needed:
- "iosc": the SoC's internal frequency oscillator
Example for generic CCU:
ccu: clock@01c20000 {
ccu: clock@1c20000 {
compatible = "allwinner,sun8i-h3-ccu";
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
......@@ -46,7 +46,7 @@ ccu: clock@01c20000 {
};
Example for PRCM CCU:
r_ccu: clock@01f01400 {
r_ccu: clock@1f01400 {
compatible = "allwinner,sun50i-a64-r-ccu";
reg = <0x01f01400 0x100>;
clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>;
......
......@@ -137,7 +137,7 @@ the address block, which is related to the overall mmc block.
For example:
osc24M: clk@01c20050 {
osc24M: clk@1c20050 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-osc-clk";
reg = <0x01c20050 0x4>;
......@@ -145,7 +145,7 @@ osc24M: clk@01c20050 {
clock-output-names = "osc24M";
};
pll1: clk@01c20000 {
pll1: clk@1c20000 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk";
reg = <0x01c20000 0x4>;
......@@ -153,7 +153,7 @@ pll1: clk@01c20000 {
clock-output-names = "pll1";
};
pll5: clk@01c20020 {
pll5: clk@1c20020 {
#clock-cells = <1>;
compatible = "allwinner,sun4i-pll5-clk";
reg = <0x01c20020 0x4>;
......@@ -161,7 +161,7 @@ pll5: clk@01c20020 {
clock-output-names = "pll5_ddr", "pll5_other";
};
pll6: clk@01c20028 {
pll6: clk@1c20028 {
#clock-cells = <1>;
compatible = "allwinner,sun6i-a31-pll6-clk";
reg = <0x01c20028 0x4>;
......@@ -169,7 +169,7 @@ pll6: clk@01c20028 {
clock-output-names = "pll6", "pll6x2";
};
cpu: cpu@01c20054 {
cpu: cpu@1c20054 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-cpu-clk";
reg = <0x01c20054 0x4>;
......@@ -177,7 +177,7 @@ cpu: cpu@01c20054 {
clock-output-names = "cpu";
};
mmc0_clk: clk@01c20088 {
mmc0_clk: clk@1c20088 {
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20088 0x4>;
......@@ -199,7 +199,7 @@ gmac_int_tx_clk: clk@3 {
clock-output-names = "gmac_int_tx";
};
gmac_clk: clk@01c20164 {
gmac_clk: clk@1c20164 {
#clock-cells = <0>;
compatible = "allwinner,sun7i-a20-gmac-clk";
reg = <0x01c20164 0x4>;
......@@ -211,7 +211,7 @@ gmac_clk: clk@01c20164 {
clock-output-names = "gmac";
};
mmc_config_clk: clk@01c13000 {
mmc_config_clk: clk@1c13000 {
compatible = "allwinner,sun9i-a80-mmc-config-clk";
reg = <0x01c13000 0x10>;
clocks = <&ahb0_gates 8>;
......
......@@ -25,7 +25,7 @@ Example:
};
};
...
i2c0: i2c-master@0d090000 {
i2c0: i2c-master@d090000 {
...
cdce706: clock-synth@69 {
compatible = "ti,cdce706";
......
......@@ -14,7 +14,7 @@ Optional properties:
- reset-names : must contain "ahb"
Example:
crypto: crypto-engine@01c15000 {
crypto: crypto-engine@1c15000 {
compatible = "allwinner,sun4i-a10-crypto";
reg = <0x01c15000 0x1000>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
......
......@@ -42,7 +42,7 @@ Optional properties:
example:
gpu_3d: gpu@00130000 {
gpu_3d: gpu@130000 {
compatible = "vivante,gc";
reg = <0x00130000 0x4000>;
interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>;
......
......@@ -32,11 +32,11 @@ Optional properties
Example:
gpr: iomuxc-gpr@020e0000 {
gpr: iomuxc-gpr@20e0000 {
/* ... */
};
hdmi: hdmi@0120000 {
hdmi: hdmi@120000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6q-hdmi";
......
......@@ -78,7 +78,7 @@ chosen {
stdout-path = "display0";
};
soc@01c00000 {
soc@1c00000 {
lcdc0: lcdc@1c0c000 {
compatible = "allwinner,sun4i-a10-lcdc";
...
......
......@@ -266,7 +266,7 @@ connector {
};
};
hdmi: hdmi@01c16000 {
hdmi: hdmi@1c16000 {
compatible = "allwinner,sun5i-a10s-hdmi";
reg = <0x01c16000 0x1000>;
interrupts = <58>;
......@@ -305,7 +305,7 @@ hdmi: hdmi@01c16000 {
};
};
tve0: tv-encoder@01c0a000 {
tve0: tv-encoder@1c0a000 {
compatible = "allwinner,sun4i-a10-tv-encoder";
reg = <0x01c0a000 0x1000>;
clocks = <&ahb_gates 34>;
......
......@@ -12,7 +12,7 @@ Required properties:
second cell holding the request line number.
Example:
dma: dma-controller@01c02000 {
dma: dma-controller@1c02000 {
compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>;
interrupts = <27>;
......@@ -32,7 +32,7 @@ The three cells in order are:
3. The port ID as specified in the datasheet
Example:
spi2: spi@01c17000 {
spi2: spi@1c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
interrupts = <0 12 4>;
......
......@@ -38,7 +38,7 @@ The two cells in order are:
2. The port ID as specified in the datasheet
Example:
spi2: spi@01c6a000 {
spi2: spi@1c6a000 {
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c6a000 0x1000>;
interrupts = <0 67 4>;
......
......@@ -142,7 +142,7 @@ mcasp0: mcasp@48038000 {
};
2.
edma1: edma@02728000 {
edma1: edma@2728000 {
compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
reg = <0x02728000 0x8000>;
reg-names = "edma3_cc";
......@@ -165,13 +165,13 @@ edma1: edma@02728000 {
power-domains = <&k2g_pds 0x4f>;
};
edma1_tptc0: tptc@027b0000 {
edma1_tptc0: tptc@27b0000 {
compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b0000 0x400>;
power-domains = <&k2g_pds 0x4f>;
};
edma1_tptc1: tptc@027b8000 {
edma1_tptc1: tptc@27b8000 {
compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b8000 0x400>;
power-domains = <&k2g_pds 0x4f>;
......
......@@ -26,7 +26,7 @@ Controller:
Client:
Use specific request line passing from dmax
For example, spdif0 tx channel request line is 4
spdif0: spdif0@0b004000 {
spdif0: spdif0@b004000 {
#sound-dai-cells = <0>;
compatible = "zte,zx296702-spdif";
reg = <0x0b004000 0x1000>;
......
......@@ -66,7 +66,7 @@ See ".../sram/sram.txt" for the bindings.
Example:
hsp_top0: hsp@03c00000 {
hsp_top0: hsp@3c00000 {
...
#mbox-cells = <2>;
};
......
......@@ -25,7 +25,7 @@ Please refer to gpio.txt in this directory for details of the common GPIO
bindings used by client devices.
Example:
dspgpio0: keystone_dsp_gpio@02620240 {
dspgpio0: keystone_dsp_gpio@2620240 {
compatible = "ti,keystone-dsp-gpio";
ti,syscon-dev = <&devctrl 0x240>;
gpio-controller;
......
......@@ -30,7 +30,7 @@ Optional properties:
Example:
pdc_gpios: gpio-controller@02006500 {
pdc_gpios: gpio-controller@2006500 {
gpio-controller;
#gpio-cells = <2>;
......
......@@ -59,7 +59,7 @@ Required properties:
Example:
gpios: gpio-controller@02005800 {
gpios: gpio-controller@2005800 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "img,tz1090-gpio";
......
......@@ -17,7 +17,7 @@ Optional properties :
Example :
i2c@02010084000 {
i2c@2010084000 {
compatible = "lsi,api2c";
device_type = "i2c";
#address-cells = <1>;
......
......@@ -24,7 +24,7 @@ Slave device properties:
Example:
p2wi@01f03400 {
p2wi@1f03400 {
compatible = "allwinner,sun6i-a31-p2wi";
reg = <0x01f03400 0x400>;
interrupts = <0 39 4>;
......
......@@ -19,7 +19,7 @@ Optional properties:
Example:
ak8974@0f {
ak8974@f {
compatible = "asahi-kasei,ak8974";
reg = <0x0f>;
avdd-supply = <&foo_reg>;
......
......@@ -13,7 +13,7 @@ Optional properties:
Example:
ak8975@0c {
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0x0c>;
gpios = <&gpj0 7 0>;
......
......@@ -19,7 +19,7 @@ Example:
#include <dt-bindings/input/input.h>
lradc: lradc@01c22800 {
lradc: lradc@1c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
interrupts = <31>;
......
......@@ -10,7 +10,7 @@ Required properties:
Example:
egalax_ts@04 {
touchscreen@4 {
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio1>;
......
......@@ -21,7 +21,7 @@ Optional properties:
each read. Valid values are 1, 4, 8, 16 and 32.
Example:
tsc: tsc@02040000 {
tsc: tsc@2040000 {
compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
......
......@@ -20,7 +20,7 @@ Required properties:
Example:
sc-nmi-intc@01c00030 {
sc-nmi-intc@1c00030 {
compatible = "allwinner,sun7i-a20-sc-nmi";
interrupt-controller;
#interrupt-cells = <2>;
......
......@@ -20,7 +20,7 @@ Please refer to interrupts.txt in this directory for details of the common
Interrupt Controllers bindings used by client devices.
Example:
kirq0: keystone_irq0@026202a0 {
kirq0: keystone_irq0@26202a0 {
compatible = "ti,keystone-irq";
ti,syscon-dev = <&devctrl 0x2a0>;
interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
......
......@@ -115,7 +115,7 @@ to non-secure vs secure interrupt line.
iommus = <&apps_iommu 4>;
};
gpu@01c00000 {
gpu@1c00000 {
...
iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
};
......@@ -32,7 +32,7 @@ syscon: syscon@10000000 {
compatible = "arm,realview-pb1176-syscon", "syscon";
reg = <0x10000000 0x1000>;
led@08.0 {
led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
......@@ -40,7 +40,7 @@ syscon: syscon@10000000 {
linux,default-trigger = "heartbeat";
default-state = "on";
};
led@08.1 {
led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
......@@ -48,7 +48,7 @@ syscon: syscon@10000000 {
linux,default-trigger = "mmc0";
default-state = "off";
};
led@08.2 {
led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
......@@ -56,35 +56,35 @@ syscon: syscon@10000000 {
linux,default-trigger = "cpu0";
default-state = "off";
};
led@08.3 {
led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
label = "versatile:3";
default-state = "off";
};
led@08.4 {
led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
label = "versatile:4";
default-state = "off";
};
led@08.5 {
led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
label = "versatile:5";
default-state = "off";
};
led@08.6 {
led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
led@08.7 {
led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
......
......@@ -29,7 +29,7 @@ Required properties:
Example(K2G):
------------
msgmgr: msgmgr@02a00000 {
msgmgr: msgmgr@2a00000 {
compatible = "ti,k2g-message-manager";
#mbox-cells = <2>;
reg-names = "queue_proxy_region", "queue_state_debug_region";
......
......@@ -446,7 +446,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
that services interrupts for this device.
Example Discovery CPU Error node:
cpu-error@0070 {
cpu-error@70 {
compatible = "marvell,mv64360-cpu-error";
reg = <0x70 0x10 0x128 0x28>;
interrupts = <3>;
......@@ -466,7 +466,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
that services interrupts for this device.
Example Discovery SRAM Controller node:
sram-ctrl@0380 {
sram-ctrl@380 {
compatible = "marvell,mv64360-sram-ctrl";
reg = <0x380 0x80>;
interrupts = <13>;
......
......@@ -27,7 +27,7 @@ Documentation/devicetree/bindings/media/video-interfaces.txt.
Example:
tc358743@0f {
tc358743@f {
compatible = "toshiba,tc358743";
reg = <0x0f>;
clocks = <&hdmi_osc>;
......
......@@ -25,7 +25,7 @@ Optional properties:
Example:
ir@02006200 {
ir@2006200 {
compatible = "img,ir-rev1";
reg = <0x02006200 0x100>;
interrupts = <29 4>;
......
......@@ -13,7 +13,7 @@ Required properties:
Example for STIH407:
sti-cec@094a087c {
sti-cec@94a087c {
compatible = "st,stih-cec";
reg = <0x94a087c 0x64>;
clocks = <&clk_sysin>;
......
......@@ -50,7 +50,7 @@ Example:
/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
c8sectpfe@08a20000 {
c8sectpfe@8a20000 {
compatible = "st,stih407-c8sectpfe";
reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
reg-names = "stfe", "stfe-ram";
......
......@@ -14,7 +14,7 @@ Optional properties:
Example:
ir0: ir@01c21800 {
ir0: ir@1c21800 {
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>;
clock-names = "apb", "ir";
......
......@@ -19,7 +19,7 @@ Required properties:
Example:
max77686: pmic@09 {
max77686: pmic@9 {
compatible = "maxim,max77686";
interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>;
......