diff --git a/Documentation/ABI/testing/sysfs-class-power b/Documentation/ABI/testing/sysfs-class-power
index 216d61a22f1e72cadb1961fc3ad8a774fcb7395d..40213c73bc9c45388085367c062b933adbfce163 100644
--- a/Documentation/ABI/testing/sysfs-class-power
+++ b/Documentation/ABI/testing/sysfs-class-power
@@ -205,7 +205,8 @@ Description:
 		Valid values: "Unknown", "Good", "Overheat", "Dead",
 			      "Over voltage", "Unspecified failure", "Cold",
 			      "Watchdog timer expire", "Safety timer expire",
-			      "Over current", "Calibration required"
+			      "Over current", "Calibration required", "Warm",
+			      "Cool", "Hot"
 
 What:		/sys/class/power_supply/<supply_name>/precharge_current
 Date:		June 2017
diff --git a/Documentation/ABI/testing/sysfs-class-power-wilco b/Documentation/ABI/testing/sysfs-class-power-wilco
index da1d6ffe5e3ce8eb0a8287158726fa934f651e65..84fde1d0ada065e1fd972acaea4eef4d8c4b7b73 100644
--- a/Documentation/ABI/testing/sysfs-class-power-wilco
+++ b/Documentation/ABI/testing/sysfs-class-power-wilco
@@ -14,6 +14,10 @@ Description:
 			Charging begins when level drops below
 			charge_control_start_threshold, and ceases when
 			level is above charge_control_end_threshold.
+		Long Life: Customized charge rate for last longer battery life.
+			On Wilco device this mode is pre-configured in the factory
+			through EC's private PID. Swiching to a different mode will
+			be denied by Wilco EC when Long Life mode is enabled.
 
 What:		/sys/class/power_supply/wilco-charger/charge_control_start_threshold
 Date:		April 2019
diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt
index 5e29595edd74ad460c7444351db58177ac32feb7..a9f80cc490680b3ddf6cf5356a41fd433316c532 100644
--- a/Documentation/devicetree/bindings/power/supply/battery.txt
+++ b/Documentation/devicetree/bindings/power/supply/battery.txt
@@ -1,87 +1,3 @@
-Battery Characteristics
-
-The devicetree battery node provides static battery characteristics.
-In smart batteries, these are typically stored in non-volatile memory
-on a fuel gauge chip. The battery node should be used where there is
-no appropriate non-volatile memory, or it is unprogrammed/incorrect.
-
-Upstream dts files should not include battery nodes, unless the battery
-represented cannot easily be replaced in the system by one of a
-different type. This prevents unpredictable, potentially harmful,
-behavior should a replacement that changes the battery type occur
-without a corresponding update to the dtb.
+The contents of this file has been moved to battery.yaml
 
 Please note that not all charger drivers respect all of the properties.
-
-Required Properties:
- - compatible: Must be "simple-battery"
-
-Optional Properties:
- - over-voltage-threshold-microvolt: battery over-voltage limit
- - re-charge-voltage-microvolt: limit to automatically start charging again
- - voltage-min-design-microvolt: drained battery voltage
- - voltage-max-design-microvolt: fully charged battery voltage
- - energy-full-design-microwatt-hours: battery design energy
- - charge-full-design-microamp-hours: battery design capacity
- - trickle-charge-current-microamp: current for trickle-charge phase
- - precharge-current-microamp: current for pre-charge phase
- - precharge-upper-limit-microvolt: limit when to change to constant charging
- - charge-term-current-microamp: current for charge termination phase
- - constant-charge-current-max-microamp: maximum constant input current
- - constant-charge-voltage-max-microvolt: maximum constant input voltage
- - factory-internal-resistance-micro-ohms: battery factory internal resistance
- - ocv-capacity-table-0: An array providing the open circuit voltage (OCV)
-   of the battery and corresponding battery capacity percent, which is used
-   to look up battery capacity according to current OCV value. And the open
-   circuit voltage unit is microvolt.
- - ocv-capacity-table-1: Same as ocv-capacity-table-0
- ......
- - ocv-capacity-table-n: Same as ocv-capacity-table-0
- - ocv-capacity-celsius: An array containing the temperature in degree Celsius,
-   for each of the battery capacity lookup table. The first temperature value
-   specifies the OCV table 0, and the second temperature value specifies the
-   OCV table 1, and so on.
- - resistance-temp-table: An array providing the temperature in degree Celsius
-   and corresponding battery internal resistance percent, which is used to look
-   up the resistance percent according to current temperature to get a accurate
-   batterty internal resistance in different temperatures.
-
-Battery properties are named, where possible, for the corresponding
-elements in enum power_supply_property, defined in
-https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h
-
-Batteries must be referenced by chargers and/or fuel-gauges
-using a phandle. The phandle's property should be named
-"monitored-battery".
-
-Example:
-
-	bat: battery {
-		compatible = "simple-battery";
-		voltage-min-design-microvolt = <3200000>;
-		voltage-max-design-microvolt = <4200000>;
-		energy-full-design-microwatt-hours = <5290000>;
-		charge-full-design-microamp-hours = <1430000>;
-		precharge-current-microamp = <256000>;
-		charge-term-current-microamp = <128000>;
-		constant-charge-current-max-microamp = <900000>;
-		constant-charge-voltage-max-microvolt = <4200000>;
-		factory-internal-resistance-micro-ohms = <250000>;
-		ocv-capacity-celsius = <(-10) 0 10>;
-		ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, ...;
-		ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>, ...;
-		ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>, ...;
-		resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>;
-	};
-
-	charger: charger@11 {
-		....
-		monitored-battery = <&bat>;
-		...
-	};
-
-	fuel_gauge: fuel-gauge@22 {
-		....
-		monitored-battery = <&bat>;
-		...
-	};
diff --git a/Documentation/devicetree/bindings/power/supply/battery.yaml b/Documentation/devicetree/bindings/power/supply/battery.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..932b736ce5c010a1a68020ec58cd3524eb4455de
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/battery.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/supply/battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Battery Characteristics
+
+maintainers:
+  - Sebastian Reichel <sre@kernel.org>
+
+description: |
+  The devicetree battery node provides static battery characteristics.
+  In smart batteries, these are typically stored in non-volatile memory
+  on a fuel gauge chip. The battery node should be used where there is
+  no appropriate non-volatile memory, or it is unprogrammed/incorrect.
+
+  Upstream dts files should not include battery nodes, unless the battery
+  represented cannot easily be replaced in the system by one of a
+  different type. This prevents unpredictable, potentially harmful,
+  behavior should a replacement that changes the battery type occur
+  without a corresponding update to the dtb.
+
+  Battery properties are named, where possible, for the corresponding elements
+  in enum power_supply_property, defined in include/linux/power_supply.h
+
+  Batteries must be referenced by chargers and/or fuel-gauges using a phandle.
+  The phandle's property should be named "monitored-battery".
+
+properties:
+  compatible:
+    const: simple-battery
+
+  over-voltage-threshold-microvolt:
+    description: battery over-voltage limit
+
+  re-charge-voltage-microvolt:
+    description: limit to automatically start charging again
+
+  voltage-min-design-microvolt:
+    description: drained battery voltage
+
+  voltage-max-design-microvolt:
+    description: fully charged battery voltage
+
+  energy-full-design-microwatt-hours:
+    description: battery design energy
+
+  charge-full-design-microamp-hours:
+    description: battery design capacity
+
+  trickle-charge-current-microamp:
+    description: current for trickle-charge phase
+
+  precharge-current-microamp:
+    description: current for pre-charge phase
+
+  precharge-upper-limit-microvolt:
+    description: limit when to change to constant charging
+
+  charge-term-current-microamp:
+    description: current for charge termination phase
+
+  constant-charge-current-max-microamp:
+    description: maximum constant input current
+
+  constant-charge-voltage-max-microvolt:
+    description: maximum constant input voltage
+
+  factory-internal-resistance-micro-ohms:
+    description: battery factory internal resistance
+
+  resistance-temp-table:
+    description: |
+      An array providing the temperature in degree Celsius
+      and corresponding battery internal resistance percent, which is used to
+      look up the resistance percent according to current temperature to get an
+      accurate batterty internal resistance in different temperatures.
+
+  ocv-capacity-celsius:
+    description: |
+      An array containing the temperature in degree Celsius,
+      for each of the battery capacity lookup table.
+
+required:
+  - compatible
+
+patternProperties:
+  '^ocv-capacity-table-[0-9]+$':
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    description: |
+      An array providing the open circuit voltage (OCV)
+      of the battery and corresponding battery capacity percent, which is used
+      to look up battery capacity according to current OCV value. And the open
+      circuit voltage unit is microvolt.
+    maxItems: 100
+    items:
+      items:
+        - description: open circuit voltage (OCV) in microvolts
+        - description: battery capacity percent
+          maximum: 100
+
+additionalProperties: false
+
+examples:
+  - |
+    power {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      battery: battery {
+        compatible = "simple-battery";
+        over-voltage-threshold-microvolt = <4500000>;
+        re-charge-voltage-microvolt = <250000>;
+        voltage-min-design-microvolt = <3200000>;
+        voltage-max-design-microvolt = <4200000>;
+        energy-full-design-microwatt-hours = <5290000>;
+        charge-full-design-microamp-hours = <1430000>;
+        precharge-current-microamp = <256000>;
+        precharge-upper-limit-microvolt = <2500000>;
+        charge-term-current-microamp = <128000>;
+        constant-charge-current-max-microamp = <900000>;
+        constant-charge-voltage-max-microvolt = <4200000>;
+        factory-internal-resistance-micro-ohms = <250000>;
+        ocv-capacity-celsius = <(-10) 0 10>;
+        /* table for -10 degree Celsius */
+        ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>;
+        /* table for 0 degree Celsius */
+        ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>;
+        /* table for 10 degree Celsius */
+        ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>;
+        resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>;
+      };
+
+      charger@11 {
+        reg = <0x11>;
+        monitored-battery = <&battery>;
+      };
+
+      fuel-gauge@22 {
+        reg = <0x22>;
+        monitored-battery = <&battery>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..75a56773be4a0a364909feff196b2e81dc6288e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
@@ -0,0 +1,93 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI bq2515x 500-mA Linear charger family
+
+maintainers:
+  - Dan Murphy <dmurphy@ti.com>
+  - Ricardo Rivera-Matos <r-rivera-matos@ti.com>
+
+description: |
+  The BQ2515x family is a highly integrated battery charge management IC that
+  integrates the most common functions for wearable devices, namely a charger,
+  an output voltage rail, ADC for battery and system monitoring, and
+  push-button controller.
+
+  Specifications about the charger can be found at:
+    http://www.ti.com/lit/ds/symlink/bq25150.pdf
+    http://www.ti.com/lit/ds/symlink/bq25155.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,bq25150
+      - ti,bq25155
+
+  reg:
+    maxItems: 1
+    description: I2C address of the charger.
+
+  ac-detect-gpios:
+    description: |
+       GPIO used for connecting the bq2515x device PG (AC Detect)
+       pin.
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO used for hardware reset.
+    maxItems: 1
+
+  powerdown-gpios:
+    description: GPIO used for low power mode of IC.
+    maxItems: 1
+
+  charge-enable-gpios:
+    description: GPIO used to turn on and off charging.
+    maxItems: 1
+
+  input-current-limit-microamp:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Maximum input current in micro Amps.
+    minimum: 50000
+    maximum: 500000
+
+  monitored-battery:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the battery node being monitored
+
+required:
+  - compatible
+  - reg
+  - monitored-battery
+
+additionalProperties: false
+
+examples:
+  - |
+    bat: battery {
+      compatible = "simple-battery";
+      constant-charge-current-max-microamp = <50000>;
+      precharge-current-microamp = <2500>;
+      constant-charge-voltage-max-microvolt = <4000000>;
+    };
+    #include <dt-bindings/gpio/gpio.h>
+    i2c0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bq25150: charger@6b {
+        compatible = "ti,bq25150";
+        reg = <0x6b>;
+        monitored-battery = <&bat>;
+        input-current-limit-microamp = <100000>;
+
+        ac-detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+        reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+        powerdown-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+        charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt
index dc9c8f76e06cdec9bd0ff8cb8d77574f77a764c4..3b4c69a7fa705259585cd90b5e6f394935304661 100644
--- a/Documentation/devicetree/bindings/power/supply/bq25890.txt
+++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt
@@ -10,6 +10,7 @@ Required properties:
     * "ti,bq25895"
     * "ti,bq25896"
 - reg: integer, i2c address of the device.
+- interrupts: interrupt line;
 - ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
 - ti,charge-current: integer, maximum charging current (in uA);
 - ti,termination-current: integer, charge will be terminated when current in
@@ -36,17 +37,20 @@ Optional properties:
 Example:
 
 bq25890 {
-        compatible = "ti,bq25890";
-        reg = <0x6a>;
-
-        ti,battery-regulation-voltage = <4200000>;
-        ti,charge-current = <1000000>;
-        ti,termination-current = <50000>;
-        ti,precharge-current = <128000>;
-        ti,minimum-sys-voltage = <3600000>;
-        ti,boost-voltage = <5000000>;
-        ti,boost-max-current = <1000000>;
-
-        ti,use-ilim-pin;
-        ti,thermal-regulation-threshold = <120>;
+	compatible = "ti,bq25890";
+	reg = <0x6a>;
+
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <1000000>;
+	ti,termination-current = <50000>;
+	ti,precharge-current = <128000>;
+	ti,minimum-sys-voltage = <3600000>;
+	ti,boost-voltage = <5000000>;
+	ti,boost-max-current = <1000000>;
+
+	ti,use-ilim-pin;
+	ti,thermal-regulation-threshold = <120>;
 };
diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml
index 03d1020a2e4701d56484b8439def535d36869d4a..82f682705f4495abb409270853eb5f776dcda0ae 100644
--- a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml
+++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml
@@ -49,6 +49,8 @@ properties:
       - ti,bq27426
       - ti,bq27441
       - ti,bq27621
+      - ti,bq27z561
+      - ti,bq28z610
 
   reg:
     maxItems: 1
diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.txt b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt
deleted file mode 100644
index 0fb33b2c62a6028defc2517fd22fb9bd5506e53b..0000000000000000000000000000000000000000
--- a/Documentation/devicetree/bindings/power/supply/gpio-charger.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-gpio-charger
-
-Required properties :
- - compatible : "gpio-charger"
- - gpios : GPIO indicating the charger presence.
-   See GPIO binding in bindings/gpio/gpio.txt .
- - charger-type : power supply type, one of
-     unknown
-     battery
-     ups
-     mains
-     usb-sdp (USB standard downstream port)
-     usb-dcp (USB dedicated charging port)
-     usb-cdp (USB charging downstream port)
-     usb-aca (USB accessory charger adapter)
-
-Optional properties:
- - charge-status-gpios: GPIO indicating whether a battery is charging.
-
-Example:
-
-	usb_charger: charger {
-		compatible = "gpio-charger";
-		charger-type = "usb-sdp";
-		gpios = <&gpd 28 GPIO_ACTIVE_LOW>;
-		charge-status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>;
-	};
-
-	battery {
-		power-supplies = <&usb_charger>;
-	};
diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml b/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..30eabbb14ef3392425d3d09de9fa14e01326ba69
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/supply/gpio-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: simple battery chargers only communicating through GPIOs
+
+maintainers:
+  - Sebastian Reichel <sre@kernel.org>
+
+description:
+  This binding is for all chargers, which are working more or less
+  autonomously, only providing some status GPIOs and possibly some
+  GPIOs for limited control over the charging process.
+
+properties:
+  compatible:
+    const: gpio-charger
+
+  charger-type:
+    enum:
+      - unknown
+      - battery
+      - ups
+      - mains
+      - usb-sdp                   # USB standard downstream port
+      - usb-dcp                   # USB dedicated charging port
+      - usb-cdp                   # USB charging downstream port
+      - usb-aca                   # USB accessory charger adapter
+    description:
+      Type of the charger, e.g. "mains" for a wall charger.
+
+  gpios:
+    maxItems: 1
+    description: GPIO indicating the charger presence
+
+  charge-status-gpios:
+    maxItems: 1
+    description: GPIO indicating the charging status
+
+required:
+  - compatible
+
+anyOf:
+  - required:
+    - gpios
+  - required:
+    - charge-status-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    charger {
+      compatible = "gpio-charger";
+      charger-type = "usb-sdp";
+
+      gpios = <&gpd 28 GPIO_ACTIVE_LOW>;
+      charge-status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>;
+    };
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
index f07b982c8dff0a722791acd720315677a0cf79d9..0a1fb5c74f83e4856479abc9f2654b77d730002d 100644
--- a/drivers/power/reset/Kconfig
+++ b/drivers/power/reset/Kconfig
@@ -99,6 +99,17 @@ config POWER_RESET_HISI
 	help
 	  Reboot support for Hisilicon boards.
 
+config POWER_RESET_LINKSTATION
+	tristate "Buffalo LinkStation power-off driver"
+	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on OF_MDIO && PHYLIB
+	help
+	  This driver supports turning off some Buffalo LinkStations by
+	  setting an output pin at the ethernet PHY to the correct state.
+	  It also makes the device compatible with the WoL function.
+
+	  Say Y here if you have a Buffalo LinkStation LS421D/E.
+
 config POWER_RESET_MSM
 	bool "Qualcomm MSM power-off driver"
 	depends on ARCH_QCOM
diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
index 5710ca4695170c200f69ec142b3c56ec3d393edd..c51eceba9ea39bdb05e8034e65e8f910c1ebb4f8 100644
--- a/drivers/power/reset/Makefile
+++ b/drivers/power/reset/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_POWER_RESET_GEMINI_POWEROFF) += gemini-poweroff.o
 obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
 obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o
 obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o
+obj-${CONFIG_POWER_RESET_LINKSTATION} += linkstation-poweroff.o
 obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o
 obj-$(CONFIG_POWER_RESET_MT6323) += mt6323-poweroff.o
 obj-$(CONFIG_POWER_RESET_OXNAS) += oxnas-restart.o
diff --git a/drivers/power/reset/keystone-reset.c b/drivers/power/reset/keystone-reset.c
index ad11faae19c5c0fcef13496f4a1e5d8aa14131f2..211eeef0c81aec55a50ebd82a8570de9424ebd16 100644
--- a/drivers/power/reset/keystone-reset.c
+++ b/drivers/power/reset/keystone-reset.c
@@ -2,7 +2,7 @@
 /*
  * TI keystone reboot driver
  *
- * Copyright (C) 2014 Texas Instruments Incorporated. http://www.ti.com/
+ * Copyright (C) 2014 Texas Instruments Incorporated. https://www.ti.com/
  *
  * Author: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
  */
diff --git a/drivers/power/reset/linkstation-poweroff.c b/drivers/power/reset/linkstation-poweroff.c
new file mode 100644
index 0000000000000000000000000000000000000000..39e89baedb5f92a2ddce7313c481647732102fde
--- /dev/null
+++ b/drivers/power/reset/linkstation-poweroff.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * LinkStation power off restart driver
+ * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/notifier.h>
+#include <linux/of.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/reboot.h>
+#include <linux/phy.h>
+
+/* Defines from the eth phy Marvell driver */
+#define MII_MARVELL_COPPER_PAGE		0
+#define MII_MARVELL_LED_PAGE		3
+#define MII_MARVELL_WOL_PAGE		17
+#define MII_MARVELL_PHY_PAGE		22
+
+#define MII_PHY_LED_CTRL		16
+#define MII_88E1318S_PHY_LED_TCR	18
+#define MII_88E1318S_PHY_WOL_CTRL	16
+#define MII_M1011_IEVENT		19
+
+#define MII_88E1318S_PHY_LED_TCR_INTn_ENABLE		BIT(7)
+#define MII_88E1318S_PHY_LED_TCR_FORCE_INT		BIT(15)
+#define MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS	BIT(12)
+#define LED2_FORCE_ON					(0x8 << 8)
+#define LEDMASK						GENMASK(11,8)
+
+static struct phy_device *phydev;
+
+static void mvphy_reg_intn(u16 data)
+{
+	int rc = 0, saved_page;
+
+	saved_page = phy_select_page(phydev, MII_MARVELL_LED_PAGE);
+	if (saved_page < 0)
+		goto err;
+
+	/* Force manual LED2 control to let INTn work */
+	__phy_modify(phydev, MII_PHY_LED_CTRL, LEDMASK, LED2_FORCE_ON);
+
+	/* Set the LED[2]/INTn pin to the required state */
+	__phy_modify(phydev, MII_88E1318S_PHY_LED_TCR,
+		     MII_88E1318S_PHY_LED_TCR_FORCE_INT,
+		     MII_88E1318S_PHY_LED_TCR_INTn_ENABLE | data);
+
+	if (!data) {
+		/* Clear interrupts to ensure INTn won't be holded in high state */
+		__phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_MARVELL_COPPER_PAGE);
+		__phy_read(phydev, MII_M1011_IEVENT);
+
+		/* If WOL was enabled and a magic packet was received before powering
+		 * off, we won't be able to wake up by sending another magic packet.
+		 * Clear WOL status.
+		 */
+		__phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_MARVELL_WOL_PAGE);
+		__phy_set_bits(phydev, MII_88E1318S_PHY_WOL_CTRL,
+			       MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS);
+	}
+err:
+	rc = phy_restore_page(phydev, saved_page, rc);
+	if (rc < 0)
+		dev_err(&phydev->mdio.dev, "Write register failed, %d\n", rc);
+}
+
+static int linkstation_reboot_notifier(struct notifier_block *nb,
+				       unsigned long action, void *unused)
+{
+	if (action == SYS_RESTART)
+		mvphy_reg_intn(MII_88E1318S_PHY_LED_TCR_FORCE_INT);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block linkstation_reboot_nb = {
+	.notifier_call = linkstation_reboot_notifier,
+};
+
+static void linkstation_poweroff(void)
+{
+	unregister_reboot_notifier(&linkstation_reboot_nb);
+	mvphy_reg_intn(0);
+
+	kernel_restart("Power off");
+}
+
+static const struct of_device_id ls_poweroff_of_match[] = {
+	{ .compatible = "buffalo,ls421d" },
+	{ .compatible = "buffalo,ls421de" },
+	{ },
+};
+
+static int __init linkstation_poweroff_init(void)
+{
+	struct mii_bus *bus;
+	struct device_node *dn;
+
+	dn = of_find_matching_node(NULL, ls_poweroff_of_match);
+	if (!dn)
+		return -ENODEV;
+	of_node_put(dn);
+
+	dn = of_find_node_by_name(NULL, "mdio");
+	if (!dn)
+		return -ENODEV;
+
+	bus = of_mdio_find_bus(dn);
+	of_node_put(dn);
+	if (!bus)
+		return -EPROBE_DEFER;
+
+	phydev = phy_find_first(bus);
+	if (!phydev)
+		return -EPROBE_DEFER;
+
+	register_reboot_notifier(&linkstation_reboot_nb);
+	pm_power_off = linkstation_poweroff;
+
+	return 0;
+}
+
+static void __exit linkstation_poweroff_exit(void)
+{
+	pm_power_off = NULL;
+	unregister_reboot_notifier(&linkstation_reboot_nb);
+}
+
+module_init(linkstation_poweroff_init);
+module_exit(linkstation_poweroff_exit);
+
+MODULE_AUTHOR("Daniel González Cabanelas <dgcbueu@gmail.com>");
+MODULE_DESCRIPTION("LinkStation power off driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/power/supply/88pm860x_battery.c b/drivers/power/supply/88pm860x_battery.c
index 1308f3a185f3d4419cdebbbe03867af7a9dce8c5..590da88a17a253bae29f2f20538b9683b4247052 100644
--- a/drivers/power/supply/88pm860x_battery.c
+++ b/drivers/power/supply/88pm860x_battery.c
@@ -433,7 +433,7 @@ static void pm860x_init_battery(struct pm860x_battery_info *info)
 	int ret;
 	int data;
 	int bat_remove;
-	int soc;
+	int soc = 0;
 
 	/* measure enable on GPADC1 */
 	data = MEAS1_GP1;
@@ -496,7 +496,9 @@ static void pm860x_init_battery(struct pm860x_battery_info *info)
 	}
 	mutex_unlock(&info->lock);
 
-	calc_soc(info, OCV_MODE_ACTIVE, &soc);
+	ret = calc_soc(info, OCV_MODE_ACTIVE, &soc);
+	if (ret < 0)
+		goto out;
 
 	data = pm860x_reg_read(info->i2c, PM8607_POWER_UP_LOG);
 	bat_remove = data & BAT_WU_LOG;
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 44d3c8512fb8d4ef66f7fe8d9046902a479fa342..faf2830aa1527070fc84718334e0e54ba94cb3d2 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -610,6 +610,19 @@ config CHARGER_BQ24735
 	help
 	  Say Y to enable support for the TI BQ24735 battery charger.
 
+config CHARGER_BQ2515X
+	tristate "TI BQ2515X battery charger family"
+	depends on I2C
+	depends on GPIOLIB || COMPILE_TEST
+	select REGMAP_I2C
+	help
+	  Say Y to enable support for the TI BQ2515X family of battery
+	  charging integrated circuits. The BQ2515X are highly integrated
+	  battery charge management ICs that integrate the most common
+	  functions for wearable devices, namely a charger, an output voltage
+	  rail, ADC for battery and system monitoring, and push-button
+	  controller.
+
 config CHARGER_BQ25890
 	tristate "TI BQ25890 battery charger driver"
 	depends on I2C
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index b9644663e435c7b6428869d8349886ee1a06e67f..b3c694a6511443635103b9c6ba2ba0f062d0c62d 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_CHARGER_BQ2415X)	+= bq2415x_charger.o
 obj-$(CONFIG_CHARGER_BQ24190)	+= bq24190_charger.o
 obj-$(CONFIG_CHARGER_BQ24257)	+= bq24257_charger.o
 obj-$(CONFIG_CHARGER_BQ24735)	+= bq24735-charger.o
+obj-$(CONFIG_CHARGER_BQ2515X)	+= bq2515x_charger.o
 obj-$(CONFIG_CHARGER_BQ25890)	+= bq25890_charger.o
 obj-$(CONFIG_CHARGER_SMB347)	+= smb347-charger.o
 obj-$(CONFIG_CHARGER_TPS65090)	+= tps65090-charger.o
diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index 4fde24b5f35a1bb2aa939b8b17a3a744e63344da..d01dc0332edc7826c085d9147d25bb0e4a751327 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -78,7 +78,7 @@ static bool axp20x_usb_vbus_needs_polling(struct axp20x_usb_power *power)
 	/*
 	 * Polling is only necessary while VBUS is offline. While online, a
 	 * present->absent transition implies an online->offline transition
-	 * and will triger the VBUS_REMOVAL IRQ.
+	 * and will trigger the VBUS_REMOVAL IRQ.
 	 */
 	if (power->axp20x_id >= AXP221_ID && !power->online)
 		return true;
diff --git a/drivers/power/supply/bq2415x_charger.c b/drivers/power/supply/bq2415x_charger.c
index a1f00ae1c18017473f7f6bedce234c4d480c39c8..5724001e66b97dde85964161e6acd54c2532abbc 100644
--- a/drivers/power/supply/bq2415x_charger.c
+++ b/drivers/power/supply/bq2415x_charger.c
@@ -5,14 +5,14 @@
  * Copyright (C) 2011-2013  Pali Rohár <pali@kernel.org>
  *
  * Datasheets:
- * http://www.ti.com/product/bq24150
- * http://www.ti.com/product/bq24150a
- * http://www.ti.com/product/bq24152
- * http://www.ti.com/product/bq24153
- * http://www.ti.com/product/bq24153a
- * http://www.ti.com/product/bq24155
- * http://www.ti.com/product/bq24157s
- * http://www.ti.com/product/bq24158
+ * https://www.ti.com/product/bq24150
+ * https://www.ti.com/product/bq24150a
+ * https://www.ti.com/product/bq24152
+ * https://www.ti.com/product/bq24153
+ * https://www.ti.com/product/bq24153a
+ * https://www.ti.com/product/bq24155
+ * https://www.ti.com/product/bq24157s
+ * https://www.ti.com/product/bq24158
  */
 
 #include <linux/kernel.h>
diff --git a/drivers/power/supply/bq24190_charger.c b/drivers/power/supply/bq24190_charger.c
index 4540e913057f15cde4c79b290a2e2b992491aea2..d14186525e1e90d6ecc1f315d2dae3277907c18f 100644
--- a/drivers/power/supply/bq24190_charger.c
+++ b/drivers/power/supply/bq24190_charger.c
@@ -481,8 +481,10 @@ static ssize_t bq24190_sysfs_store(struct device *dev,
 		return ret;
 
 	ret = pm_runtime_get_sync(bdi->dev);
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_noidle(bdi->dev);
 		return ret;
+	}
 
 	ret = bq24190_write_mask(bdi, info->reg, info->mask, info->shift, v);
 	if (ret)
diff --git a/drivers/power/supply/bq24257_charger.c b/drivers/power/supply/bq24257_charger.c
index eb151687beb3aa9b5323ee66330530dc398831e2..8e60cb0f3c3f274b073acf3523f0d17904c7f499 100644
--- a/drivers/power/supply/bq24257_charger.c
+++ b/drivers/power/supply/bq24257_charger.c
@@ -5,9 +5,9 @@
  * Copyright (C) 2015 Intel Corporation
  *
  * Datasheets:
- * http://www.ti.com/product/bq24250
- * http://www.ti.com/product/bq24251
- * http://www.ti.com/product/bq24257
+ * https://www.ti.com/product/bq24250
+ * https://www.ti.com/product/bq24251
+ * https://www.ti.com/product/bq24257
  */
 
 #include <linux/module.h>
diff --git a/drivers/power/supply/bq2515x_charger.c b/drivers/power/supply/bq2515x_charger.c
new file mode 100644
index 0000000000000000000000000000000000000000..36b0c8c98d40cf3f3fac39aecba661b2dd624d35
--- /dev/null
+++ b/drivers/power/supply/bq2515x_charger.c
@@ -0,0 +1,1169 @@
+// SPDX-License-Identifier: GPL-2.0
+// BQ2515X Battery Charger Driver
+// Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/gpio/consumer.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#define BQ2515X_MANUFACTURER "Texas Instruments"
+
+#define BQ2515X_STAT0		0x00
+#define BQ2515X_STAT1		0x01
+#define BQ2515X_STAT2		0x02
+#define BQ2515X_FLAG0		0x03
+#define BQ2515X_FLAG1		0x04
+#define BQ2515X_FLAG2		0x05
+#define BQ2515X_FLAG3		0x06
+#define BQ2515X_MASK0		0x07
+#define BQ2515X_MASK1		0x08
+#define BQ2515X_MASK2		0x09
+#define BQ2515X_MASK3		0x0a
+#define BQ2515X_VBAT_CTRL	0x12
+#define BQ2515X_ICHG_CTRL	0x13
+#define BQ2515X_PCHRGCTRL	0x14
+#define BQ2515X_TERMCTRL	0x15
+#define BQ2515X_BUVLO		0x16
+#define BQ2515X_CHARGERCTRL0	0x17
+#define BQ2515X_CHARGERCTRL1	0x18
+#define BQ2515X_ILIMCTRL	0x19
+#define BQ2515X_LDOCTRL		0x1d
+#define BQ2515X_MRCTRL		0x30
+#define BQ2515X_ICCTRL0		0x35
+#define BQ2515X_ICCTRL1		0x36
+#define BQ2515X_ICCTRL2		0x37
+#define BQ2515X_ADCCTRL0	0x40
+#define BQ2515X_ADCCTRL1	0x41
+#define BQ2515X_ADC_VBAT_M	0x42
+#define BQ2515X_ADC_VBAT_L	0x43
+#define BQ2515X_ADC_TS_M	0x44
+#define BQ2515X_ADC_TS_L	0x45
+#define BQ2515X_ADC_ICHG_M	0x46
+#define BQ2515X_ADC_ICHG_L	0x47
+#define BQ2515X_ADC_ADCIN_M	0x48
+#define BQ2515X_ADC_ADCIN_L	0x49
+#define BQ2515X_ADC_VIN_M	0x4a
+#define BQ2515X_ADC_VIN_L	0x4b
+#define BQ2515X_ADC_PMID_M	0x4c
+#define BQ2515X_ADC_PMID_L	0x4d
+#define BQ2515X_ADC_IIN_M	0x4e
+#define BQ2515X_ADC_IIN_L	0x4f
+#define BQ2515X_ADC_COMP1_M	0x52
+#define BQ2515X_ADC_COMP1_L	0X53
+#define BQ2515X_ADC_COMP2_M	0X54
+#define BQ2515X_ADC_COMP2_L	0x55
+#define BQ2515X_ADC_COMP3_M	0x56
+#define BQ2515X_ADC_COMP3_L	0x57
+#define BQ2515X_ADC_READ_EN	0x58
+#define BQ2515X_TS_FASTCHGCTRL	0x61
+#define BQ2515X_TS_COLD		0x62
+#define BQ2515X_TS_COOL		0x63
+#define BQ2515X_TS_WARM		0x64
+#define BQ2515X_TS_HOT		0x65
+#define BQ2515X_DEVICE_ID	0x6f
+
+#define BQ2515X_DEFAULT_ICHG_UA		10000
+#define BQ25150_DEFAULT_ILIM_UA		100000
+#define BQ25155_DEFAULT_ILIM_UA		500000
+#define BQ2515X_DEFAULT_VBAT_REG_UV	4200000
+#define BQ2515X_DEFAULT_IPRECHARGE_UA	2500
+
+#define BQ2515X_DIVISOR				65536
+#define BQ2515X_VBAT_BASE_VOLT			3600000
+#define BQ2515X_VBAT_REG_MAX			4600000
+#define BQ2515X_VBAT_REG_MIN			3600000
+#define BQ2515X_VBAT_STEP_UV			10000
+#define BQ2515X_UV_FACTOR			1000000
+#define BQ2515X_VBAT_MULTIPLIER			6
+#define BQ2515X_ICHG_DIVISOR			52429
+#define BQ2515X_ICHG_CURR_STEP_THRESH_UA	318750
+#define BQ2515X_ICHG_MIN_UA			0
+#define BQ2515X_ICHG_MAX_UA			500000
+#define BQ2515X_ICHG_RNG_1B0_UA			1250
+#define BQ2515X_ICHG_RNG_1B1_UA			2500
+#define BQ2515X_VLOWV_SEL_1B0_UV		3000000
+#define BQ2515X_VLOWV_SEL_1B1_UV		2800000
+#define BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA	18750
+#define BQ2515X_PRECHRG_ICHRG_RNGE_3750_UA	37500
+#define BQ2515X_TWAKE2_MIN_US			1700000
+#define BQ2515X_TWAKE2_MAX_US			2300000
+
+#define BQ2515X_ILIM_150MA	0x2
+#define BQ2515X_ILIM_MASK	0x7
+#define BQ2515X_ILIM_MIN	50000
+#define BQ2515X_ILIM_MAX	600000
+#define BQ2515X_HEALTH_MASK	0xf
+#define BQ2515X_ICHGRNG_MASK	0x80
+#define BQ2515X_STAT0_MASK	0x0f
+#define BQ2515X_STAT1_MASK	0x1f
+#define BQ2515X_PRECHARGE_MASK	0x1f
+
+#define BQ2515X_TS_HOT_STAT		BIT(0)
+#define BQ2515X_TS_WARM_STAT		BIT(1)
+#define BQ2515X_TS_COOL_STAT		BIT(2)
+#define BQ2515X_TS_COLD_STAT		BIT(3)
+#define BQ2515X_SAFETY_TIMER_EXP	BIT(5)
+
+#define BQ2515X_EN_VBAT_READ		BIT(3)
+#define BQ2515X_EN_ICHG_READ		BIT(5)
+
+#define BQ2515X_VIN_GOOD		BIT(0)
+#define BQ2515X_CHRG_DONE		BIT(5)
+#define BQ2515X_CV_CHRG_MODE		BIT(6)
+
+#define BQ2515X_VIN_OVP_FAULT_STAT	BIT(7)
+
+#define BQ2515X_WATCHDOG_DISABLE	BIT(4)
+
+#define BQ2515X_ICHARGE_RANGE		BIT(7)
+
+#define BQ2515X_VLOWV_SEL		BIT(5)
+
+#define BQ2515X_CHARGER_DISABLE		BIT(0)
+
+#define BQ2515X_HWRESET_14S_WD		BIT(1)
+
+static const int bq2515x_ilim_lvl_values[] = {
+	50000, 100000, 150000, 200000, 300000, 400000, 500000, 600000
+};
+
+/**
+ * struct bq2515x_init_data -
+ * @ilim: input current limit
+ * @ichg: fast charge current
+ * @vbatreg: battery regulation voltage
+ * @iprechg: precharge current
+ */
+struct bq2515x_init_data {
+	int ilim;
+	int ichg;
+	int vbatreg;
+	int iprechg;
+};
+
+enum bq2515x_id {
+	BQ25150,
+	BQ25155,
+};
+
+/**
+ * struct bq2515x_device -
+ * @mains: mains properties
+ * @battery: battery properties
+ * @regmap: register map structure
+ * @dev: device structure
+ *
+ * @reset_gpio: manual reset (MR) pin
+ * @powerdown_gpio: low power mode pin
+ * @ac_detect_gpio: power good (PG) pin
+ * @ce_gpio: charge enable (CE) pin
+ *
+ * @model_name: string value describing device model
+ * @device_id: value of device_id
+ * @mains_online: boolean value indicating power supply online
+ *
+ * @bq2515x_init_data init_data: charger initialization data structure
+ */
+struct bq2515x_device {
+	struct power_supply *mains;
+	struct power_supply *battery;
+	struct regmap *regmap;
+	struct device *dev;
+
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *powerdown_gpio;
+	struct gpio_desc *ac_detect_gpio;
+	struct gpio_desc *ce_gpio;
+
+	char model_name[I2C_NAME_SIZE];
+	int device_id;
+	bool mains_online;
+
+	struct bq2515x_init_data init_data;
+};
+
+static struct reg_default bq25150_reg_defaults[] = {
+	{BQ2515X_FLAG0, 0x0},
+	{BQ2515X_FLAG1, 0x0},
+	{BQ2515X_FLAG2, 0x0},
+	{BQ2515X_FLAG3, 0x0},
+	{BQ2515X_MASK0, 0x0},
+	{BQ2515X_MASK1, 0x0},
+	{BQ2515X_MASK2, 0x71},
+	{BQ2515X_MASK3, 0x0},
+	{BQ2515X_VBAT_CTRL, 0x3C},
+	{BQ2515X_ICHG_CTRL, 0x8},
+	{BQ2515X_PCHRGCTRL, 0x2},
+	{BQ2515X_TERMCTRL, 0x14},
+	{BQ2515X_BUVLO, 0x0},
+	{BQ2515X_CHARGERCTRL0, 0x82},
+	{BQ2515X_CHARGERCTRL1, 0x42},
+	{BQ2515X_ILIMCTRL, 0x1},
+	{BQ2515X_LDOCTRL, 0xB0},
+	{BQ2515X_MRCTRL, 0x2A},
+	{BQ2515X_ICCTRL0, 0x10},
+	{BQ2515X_ICCTRL1, 0x0},
+	{BQ2515X_ICCTRL2, 0x0},
+	{BQ2515X_ADCCTRL0, 0x2},
+	{BQ2515X_ADCCTRL1, 0x40},
+	{BQ2515X_ADC_COMP1_M, 0x23},
+	{BQ2515X_ADC_COMP1_L, 0x20},
+	{BQ2515X_ADC_COMP2_M, 0x38},
+	{BQ2515X_ADC_COMP2_L, 0x90},
+	{BQ2515X_ADC_COMP3_M, 0x0},
+	{BQ2515X_ADC_COMP3_L, 0x0},
+	{BQ2515X_ADC_READ_EN, 0x0},
+	{BQ2515X_TS_FASTCHGCTRL, 0x34},
+	{BQ2515X_TS_COLD, 0x7C},
+	{BQ2515X_TS_COOL, 0x6D},
+	{BQ2515X_TS_WARM, 0x38},
+	{BQ2515X_TS_HOT, 0x27},
+	{BQ2515X_DEVICE_ID, 0x20},
+};
+
+static struct reg_default bq25155_reg_defaults[] = {
+	{BQ2515X_FLAG0, 0x0},
+	{BQ2515X_FLAG1, 0x0},
+	{BQ2515X_FLAG2, 0x0},
+	{BQ2515X_FLAG3, 0x0},
+	{BQ2515X_MASK0, 0x0},
+	{BQ2515X_MASK1, 0x0},
+	{BQ2515X_MASK2, 0x71},
+	{BQ2515X_MASK3, 0x0},
+	{BQ2515X_VBAT_CTRL, 0x3C},
+	{BQ2515X_ICHG_CTRL, 0x8},
+	{BQ2515X_PCHRGCTRL, 0x2},
+	{BQ2515X_TERMCTRL, 0x14},
+	{BQ2515X_BUVLO, 0x0},
+	{BQ2515X_CHARGERCTRL0, 0x82},
+	{BQ2515X_CHARGERCTRL1, 0xC2},
+	{BQ2515X_ILIMCTRL, 0x6},
+	{BQ2515X_LDOCTRL, 0xB0},
+	{BQ2515X_MRCTRL, 0x2A},
+	{BQ2515X_ICCTRL0, 0x10},
+	{BQ2515X_ICCTRL1, 0x0},
+	{BQ2515X_ICCTRL2, 0x40},
+	{BQ2515X_ADCCTRL0, 0x2},
+	{BQ2515X_ADCCTRL1, 0x40},
+	{BQ2515X_ADC_COMP1_M, 0x23},
+	{BQ2515X_ADC_COMP1_L, 0x20},
+	{BQ2515X_ADC_COMP2_M, 0x38},
+	{BQ2515X_ADC_COMP2_L, 0x90},
+	{BQ2515X_ADC_COMP3_M, 0x0},
+	{BQ2515X_ADC_COMP3_L, 0x0},
+	{BQ2515X_ADC_READ_EN, 0x0},
+	{BQ2515X_TS_FASTCHGCTRL, 0x34},
+	{BQ2515X_TS_COLD, 0x7C},
+	{BQ2515X_TS_COOL, 0x6D},
+	{BQ2515X_TS_WARM, 0x38},
+	{BQ2515X_TS_HOT, 0x27},
+	{BQ2515X_DEVICE_ID, 0x35},
+};
+
+static int bq2515x_wake_up(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	int val;
+
+	/* Read the STAT register if we can read it then the device is out
+	 * of ship mode.  If the register cannot be read then attempt to wake
+	 * it up and enable the ADC.
+	 */
+	ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &val);
+	if (ret)
+		return ret;
+
+	/* Need to toggle LP and bring device out of ship mode. The device
+	 * will exit the ship mode when the MR pin is held low for at least
+	 * t_WAKE2 as shown in section 8.3.7.1 of the datasheet.
+	 */
+	gpiod_set_value_cansleep(bq2515x->powerdown_gpio, 0);
+
+	gpiod_set_value_cansleep(bq2515x->reset_gpio, 0);
+	usleep_range(BQ2515X_TWAKE2_MIN_US, BQ2515X_TWAKE2_MAX_US);
+	gpiod_set_value_cansleep(bq2515x->reset_gpio, 1);
+
+	return regmap_write(bq2515x->regmap, BQ2515X_ADC_READ_EN,
+				(BQ2515X_EN_VBAT_READ | BQ2515X_EN_ICHG_READ));
+}
+
+static int bq2515x_update_ps_status(struct bq2515x_device *bq2515x)
+{
+	bool dc = false;
+	unsigned int val;
+	int ret;
+
+	if (bq2515x->ac_detect_gpio)
+		val = gpiod_get_value_cansleep(bq2515x->ac_detect_gpio);
+	else {
+		ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &val);
+		if (ret)
+			return ret;
+	}
+
+	dc = val & BQ2515X_VIN_GOOD;
+
+	ret = bq2515x->mains_online != dc;
+
+	bq2515x->mains_online = dc;
+
+	return ret;
+}
+
+static int bq2515x_disable_watchdog_timers(struct bq2515x_device *bq2515x)
+{
+	int ret;
+
+	ret = regmap_update_bits(bq2515x->regmap, BQ2515X_CHARGERCTRL0,
+			BQ2515X_WATCHDOG_DISABLE, BQ2515X_WATCHDOG_DISABLE);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(bq2515x->regmap, BQ2515X_ICCTRL2,
+						BQ2515X_HWRESET_14S_WD, 0);
+}
+
+static int bq2515x_get_battery_voltage_now(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	int vbat_msb;
+	int vbat_lsb;
+	uint32_t vbat_measurement;
+
+	if (!bq2515x->mains_online)
+		bq2515x_wake_up(bq2515x);
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_VBAT_M, &vbat_msb);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_VBAT_L, &vbat_lsb);
+	if (ret)
+		return ret;
+
+	vbat_measurement = (vbat_msb << 8) | vbat_lsb;
+
+	return vbat_measurement * (BQ2515X_UV_FACTOR / BQ2515X_DIVISOR) *
+						BQ2515X_VBAT_MULTIPLIER;
+}
+
+static int bq2515x_get_battery_current_now(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	int ichg_msb;
+	int ichg_lsb;
+	uint32_t ichg_measurement;
+	u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	unsigned int ichg_reg_code, reg_code;
+	unsigned int icharge_range = 0, pchrgctrl;
+	unsigned int buvlo, vlowv_sel, vlowv = BQ2515X_VLOWV_SEL_1B0_UV;
+
+	if (!bq2515x->mains_online)
+		return -ENODATA;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_ICHG_M, &ichg_msb);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_ICHG_L, &ichg_lsb);
+	if (ret)
+		return ret;
+
+	ichg_measurement = (ichg_msb << 8) | ichg_lsb;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_BUVLO, &buvlo);
+	if (ret)
+		return ret;
+
+	vlowv_sel = buvlo & BQ2515X_VLOWV_SEL;
+
+	if (vlowv_sel)
+		vlowv = BQ2515X_VLOWV_SEL_1B1_UV;
+
+	if (bq2515x_get_battery_voltage_now(bq2515x) < vlowv) {
+		ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL,
+								&pchrgctrl);
+		if (ret)
+			return ret;
+
+		reg_code = pchrgctrl & BQ2515X_PRECHARGE_MASK;
+	} else {
+		ret = regmap_read(bq2515x->regmap, BQ2515X_ICHG_CTRL,
+							&ichg_reg_code);
+		if (ret)
+			return ret;
+
+		reg_code = ichg_reg_code;
+	}
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
+	if (ret)
+		return ret;
+
+	icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
+
+	if (icharge_range)
+		ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
+
+	return reg_code * (ichg_multiplier * ichg_measurement /
+							BQ2515X_ICHG_DIVISOR);
+}
+
+static bool bq2515x_get_charge_disable(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	int ce_pin;
+	int icctrl2;
+	int charger_disable;
+
+	ce_pin = gpiod_get_value_cansleep(bq2515x->ce_gpio);
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ICCTRL2, &icctrl2);
+	if (ret)
+		return ret;
+
+	charger_disable = icctrl2 & BQ2515X_CHARGER_DISABLE;
+
+	if (charger_disable || ce_pin)
+		return true;
+
+	return false;
+}
+
+static int bq2515x_set_charge_disable(struct bq2515x_device *bq2515x, int val)
+{
+	gpiod_set_value_cansleep(bq2515x->ce_gpio, val);
+
+	return regmap_update_bits(bq2515x->regmap, BQ2515X_ICCTRL2,
+					BQ2515X_CHARGER_DISABLE, val);
+}
+
+static int bq2515x_get_const_charge_current(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	unsigned int ichg_reg_code;
+	unsigned int pchrgctrl;
+	unsigned int icharge_range;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ICHG_CTRL, &ichg_reg_code);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
+	if (ret)
+		return ret;
+
+	icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
+
+	if (icharge_range)
+		ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
+
+	return ichg_reg_code * ichg_multiplier;
+}
+
+static int bq2515x_set_const_charge_current(struct bq2515x_device *bq2515x,
+								int val)
+{
+	int ret;
+	unsigned int ichg_reg_code;
+	u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	unsigned int icharge_range = 0;
+
+	if (val > BQ2515X_ICHG_MAX_UA || val < BQ2515X_ICHG_MIN_UA)
+		return -EINVAL;
+
+	if (val > BQ2515X_ICHG_CURR_STEP_THRESH_UA) {
+		ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
+		icharge_range = BQ2515X_ICHARGE_RANGE;
+	}
+
+	bq2515x_set_charge_disable(bq2515x, 1);
+
+	ret = regmap_update_bits(bq2515x->regmap, BQ2515X_PCHRGCTRL,
+					BQ2515X_ICHARGE_RANGE, icharge_range);
+	if (ret)
+		return ret;
+
+	ichg_reg_code = val / ichg_multiplier;
+
+	ret = regmap_write(bq2515x->regmap, BQ2515X_ICHG_CTRL, ichg_reg_code);
+	if (ret)
+		return ret;
+
+	return bq2515x_set_charge_disable(bq2515x, 0);
+}
+
+static int bq2515x_get_precharge_current(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	unsigned int pchrgctrl;
+	unsigned int icharge_range;
+	u16 precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	unsigned int precharge_reg_code;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
+	if (ret)
+		return ret;
+
+	icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
+
+	if (icharge_range)
+		precharge_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
+
+	precharge_reg_code = pchrgctrl & BQ2515X_PRECHARGE_MASK;
+
+	return precharge_reg_code * precharge_multiplier;
+}
+
+static int bq2515x_set_precharge_current(struct bq2515x_device *bq2515x,
+					int val)
+{
+	int ret;
+	unsigned int pchrgctrl;
+	unsigned int icharge_range;
+	unsigned int precharge_reg_code;
+	unsigned int precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	unsigned int precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
+	if (ret)
+		return ret;
+
+	icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
+
+	if (icharge_range) {
+		precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_3750_UA;
+		precharge_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
+	} else {
+		precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA;
+		precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
+	}
+	if (val > precharge_max_ua || val < BQ2515X_ICHG_MIN_UA)
+		return -EINVAL;
+
+	precharge_reg_code = val / precharge_multiplier;
+
+	ret = bq2515x_set_charge_disable(bq2515x, 1);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(bq2515x->regmap, BQ2515X_PCHRGCTRL,
+				BQ2515X_PRECHARGE_MASK, precharge_reg_code);
+	if (ret)
+		return ret;
+
+	return bq2515x_set_charge_disable(bq2515x, 0);
+}
+
+static int bq2515x_charging_status(struct bq2515x_device *bq2515x,
+				   union power_supply_propval *val)
+{
+	bool status0_no_fault;
+	bool status1_no_fault;
+	bool ce_status;
+	bool charge_done;
+	unsigned int status;
+	int ret;
+
+	if (!bq2515x->mains_online) {
+		val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		return 0;
+	}
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &status);
+	if (ret)
+		return ret;
+
+	/*
+	 * The code block below is used to determine if any faults from the
+	 * STAT0 register are disbaling charging or if the charge has completed
+	 * according to the CHARGE_DONE_STAT bit.
+	 */
+	if (((status & BQ2515X_STAT0_MASK) == true) &
+			((status & BQ2515X_CHRG_DONE) == false)) {
+		status0_no_fault = true;
+		charge_done = false;
+	} else if (status & BQ2515X_CHRG_DONE) {
+		charge_done = true;
+		status0_no_fault = false;
+	} else {
+		status0_no_fault = false;
+		charge_done = false;
+	}
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_STAT1, &status);
+	if (ret)
+		return ret;
+	/*
+	 * The code block below is used to determine if any faults from the
+	 * STAT1 register are disbaling charging
+	 */
+	if ((status & BQ2515X_STAT1_MASK) == false)
+		status1_no_fault = true;
+	else
+		status1_no_fault = false;
+
+	ce_status = (!bq2515x_get_charge_disable(bq2515x));
+
+	/*
+	 * If there are no faults and charging is enabled, then status is
+	 * charging. Otherwise, if charging is complete, then status is full.
+	 * Otherwise, if a fault exists or charging is disabled, then status is
+	 * not charging
+	 */
+	if (status0_no_fault & status1_no_fault & ce_status)
+		val->intval = POWER_SUPPLY_STATUS_CHARGING;
+	else if (charge_done)
+		val->intval = POWER_SUPPLY_STATUS_FULL;
+	else if (!(status0_no_fault & status1_no_fault & ce_status))
+		val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+
+	return 0;
+}
+
+static int bq2515x_get_batt_reg(struct bq2515x_device *bq2515x)
+{
+	int vbat_reg_code;
+	int ret;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_VBAT_CTRL, &vbat_reg_code);
+	if (ret)
+		return ret;
+
+	return BQ2515X_VBAT_BASE_VOLT + vbat_reg_code * BQ2515X_VBAT_STEP_UV;
+}
+
+static int bq2515x_set_batt_reg(struct bq2515x_device *bq2515x, int val)
+{
+	int vbat_reg_code;
+
+	if (val > BQ2515X_VBAT_REG_MAX || val < BQ2515X_VBAT_REG_MIN)
+		return -EINVAL;
+
+	vbat_reg_code = (val - BQ2515X_VBAT_BASE_VOLT) / BQ2515X_VBAT_STEP_UV;
+
+	return regmap_write(bq2515x->regmap, BQ2515X_VBAT_CTRL, vbat_reg_code);
+}
+
+static int bq2515x_get_ilim_lvl(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	int ilimctrl;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_ILIMCTRL, &ilimctrl);
+	if (ret)
+		return ret;
+
+	return bq2515x_ilim_lvl_values[ilimctrl & BQ2515X_ILIM_MASK];
+}
+
+static int bq2515x_set_ilim_lvl(struct bq2515x_device *bq2515x, int val)
+{
+	int i = 0;
+	unsigned int array_size = ARRAY_SIZE(bq2515x_ilim_lvl_values);
+
+	for (i = array_size - 1; i > 0; i--) {
+		if (val >= bq2515x_ilim_lvl_values[i])
+			break;
+	}
+	return regmap_write(bq2515x->regmap, BQ2515X_ILIMCTRL, i);
+}
+
+static int bq2515x_power_supply_property_is_writeable(struct power_supply *psy,
+					enum power_supply_property prop)
+{
+	switch (prop) {
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+	case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int bq2515x_charger_get_health(struct bq2515x_device *bq2515x,
+				      union power_supply_propval *val)
+{
+	int health = POWER_SUPPLY_HEALTH_GOOD;
+	int ret;
+	unsigned int stat1;
+	unsigned int flag3;
+
+	if (!bq2515x->mains_online)
+		bq2515x_wake_up(bq2515x);
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_FLAG3, &flag3);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(bq2515x->regmap, BQ2515X_STAT1, &stat1);
+	if (ret)
+		return ret;
+
+	if (stat1 & BQ2515X_HEALTH_MASK) {
+		switch (stat1 & BQ2515X_HEALTH_MASK) {
+		case BQ2515X_TS_HOT_STAT:
+			health = POWER_SUPPLY_HEALTH_HOT;
+			break;
+		case BQ2515X_TS_WARM_STAT:
+			health = POWER_SUPPLY_HEALTH_WARM;
+			break;
+		case BQ2515X_TS_COOL_STAT:
+			health = POWER_SUPPLY_HEALTH_COOL;
+			break;
+		case BQ2515X_TS_COLD_STAT:
+			health = POWER_SUPPLY_HEALTH_COLD;
+			break;
+		default:
+			health = POWER_SUPPLY_HEALTH_UNKNOWN;
+			break;
+		}
+	}
+
+	if (stat1 & BQ2515X_VIN_OVP_FAULT_STAT)
+		health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+
+	if (flag3 & BQ2515X_SAFETY_TIMER_EXP)
+		health = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE;
+
+	val->intval = health;
+	return 0;
+}
+
+static int bq2515x_mains_set_property(struct power_supply *psy,
+		enum power_supply_property prop,
+		const union power_supply_propval *val)
+{
+	struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
+	int ret;
+
+	switch (prop) {
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+		ret = bq2515x_set_batt_reg(bq2515x, val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+		ret = bq2515x_set_const_charge_current(bq2515x, val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = bq2515x_set_ilim_lvl(bq2515x, val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
+		ret = bq2515x_set_precharge_current(bq2515x, val->intval);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int bq2515x_mains_get_property(struct power_supply *psy,
+				     enum power_supply_property prop,
+				     union power_supply_propval *val)
+{
+	struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
+	int ret = 0;
+
+	switch (prop) {
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+		ret = bq2515x_get_const_charge_current(bq2515x);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+		ret = bq2515x_get_batt_reg(bq2515x);
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
+		ret = bq2515x_get_precharge_current(bq2515x);
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = bq2515x->mains_online;
+		break;
+
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = bq2515x_charger_get_health(bq2515x, val);
+		if (ret)
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+		break;
+
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = bq2515x_get_ilim_lvl(bq2515x);
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_MODEL_NAME:
+		val->strval = bq2515x->model_name;
+		break;
+
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = BQ2515X_MANUFACTURER;
+		break;
+
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = bq2515x_charging_status(bq2515x, val);
+		if (ret)
+			return ret;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int bq2515x_battery_get_property(struct power_supply *psy,
+				       enum power_supply_property prop,
+				       union power_supply_propval *val)
+{
+	struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
+	int ret;
+
+	ret = bq2515x_update_ps_status(bq2515x);
+	if (ret)
+		return ret;
+
+	switch (prop) {
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+		ret = bq2515x->init_data.vbatreg;
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		ret = bq2515x->init_data.ichg;
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = bq2515x_get_battery_voltage_now(bq2515x);
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = bq2515x_get_battery_current_now(bq2515x);
+		if (ret < 0)
+			return ret;
+		val->intval = ret;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static enum power_supply_property bq2515x_battery_properties[] = {
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+};
+
+static enum power_supply_property bq2515x_mains_properties[] = {
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+	POWER_SUPPLY_PROP_MODEL_NAME,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+	POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
+};
+
+static struct power_supply_desc bq2515x_mains_desc = {
+	.name			= "bq2515x-mains",
+	.type			= POWER_SUPPLY_TYPE_MAINS,
+	.get_property		= bq2515x_mains_get_property,
+	.set_property		= bq2515x_mains_set_property,
+	.properties		= bq2515x_mains_properties,
+	.num_properties		= ARRAY_SIZE(bq2515x_mains_properties),
+	.property_is_writeable	= bq2515x_power_supply_property_is_writeable,
+};
+
+static struct power_supply_desc bq2515x_battery_desc = {
+	.name			= "bq2515x-battery",
+	.type			= POWER_SUPPLY_TYPE_BATTERY,
+	.get_property		= bq2515x_battery_get_property,
+	.properties		= bq2515x_battery_properties,
+	.num_properties		= ARRAY_SIZE(bq2515x_battery_properties),
+	.property_is_writeable	= bq2515x_power_supply_property_is_writeable,
+};
+
+static int bq2515x_power_supply_register(struct bq2515x_device *bq2515x,
+		struct device *dev, struct power_supply_config psy_cfg)
+{
+	bq2515x->mains = devm_power_supply_register(bq2515x->dev,
+						    &bq2515x_mains_desc,
+						    &psy_cfg);
+	if (IS_ERR(bq2515x->mains))
+		return -EINVAL;
+
+	bq2515x->battery = devm_power_supply_register(bq2515x->dev,
+						      &bq2515x_battery_desc,
+						      &psy_cfg);
+	if (IS_ERR(bq2515x->battery))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int bq2515x_hw_init(struct bq2515x_device *bq2515x)
+{
+	int ret;
+	struct power_supply_battery_info bat_info = { };
+
+	ret = bq2515x_disable_watchdog_timers(bq2515x);
+	if (ret)
+		return ret;
+
+	if (bq2515x->init_data.ilim) {
+		ret = bq2515x_set_ilim_lvl(bq2515x, bq2515x->init_data.ilim);
+		if (ret)
+			return ret;
+	}
+
+	ret = power_supply_get_battery_info(bq2515x->mains, &bat_info);
+	if (ret) {
+		dev_warn(bq2515x->dev, "battery info missing, default values will be applied\n");
+
+		bq2515x->init_data.ichg = BQ2515X_DEFAULT_ICHG_UA;
+
+		bq2515x->init_data.vbatreg = BQ2515X_DEFAULT_VBAT_REG_UV;
+
+		bq2515x->init_data.iprechg = BQ2515X_DEFAULT_IPRECHARGE_UA;
+
+	} else {
+		bq2515x->init_data.ichg =
+				bat_info.constant_charge_current_max_ua;
+
+		bq2515x->init_data.vbatreg =
+				bat_info.constant_charge_voltage_max_uv;
+
+		bq2515x->init_data.iprechg =
+				bat_info.precharge_current_ua;
+	}
+
+	ret = bq2515x_set_const_charge_current(bq2515x,
+						bq2515x->init_data.ichg);
+	if (ret)
+		return ret;
+
+	ret = bq2515x_set_batt_reg(bq2515x, bq2515x->init_data.vbatreg);
+	if (ret)
+		return ret;
+
+	return bq2515x_set_precharge_current(bq2515x,
+						bq2515x->init_data.iprechg);
+}
+
+static int bq2515x_read_properties(struct bq2515x_device *bq2515x)
+{
+	int ret;
+
+	ret = device_property_read_u32(bq2515x->dev,
+				      "input-current-limit-microamp",
+				      &bq2515x->init_data.ilim);
+	if (ret) {
+		switch (bq2515x->device_id) {
+		case BQ25150:
+			bq2515x->init_data.ilim = BQ25150_DEFAULT_ILIM_UA;
+			break;
+		case BQ25155:
+			bq2515x->init_data.ilim = BQ25155_DEFAULT_ILIM_UA;
+			break;
+		}
+	}
+
+	bq2515x->ac_detect_gpio = devm_gpiod_get_optional(bq2515x->dev,
+						   "ac-detect", GPIOD_IN);
+	if (IS_ERR(bq2515x->ac_detect_gpio)) {
+		ret = PTR_ERR(bq2515x->ac_detect_gpio);
+		dev_err(bq2515x->dev, "Failed to get ac detect");
+		return ret;
+	}
+
+	bq2515x->reset_gpio = devm_gpiod_get_optional(bq2515x->dev,
+						   "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(bq2515x->reset_gpio)) {
+		ret = PTR_ERR(bq2515x->reset_gpio);
+		dev_err(bq2515x->dev, "Failed to get reset");
+		return ret;
+	}
+
+	bq2515x->powerdown_gpio = devm_gpiod_get_optional(bq2515x->dev,
+						"powerdown", GPIOD_OUT_LOW);
+	if (IS_ERR(bq2515x->powerdown_gpio)) {
+		ret = PTR_ERR(bq2515x->powerdown_gpio);
+		dev_err(bq2515x->dev, "Failed to get powerdown");
+		return ret;
+	}
+
+	bq2515x->ce_gpio = devm_gpiod_get_optional(bq2515x->dev,
+						   "charge-enable",
+						   GPIOD_OUT_LOW);
+	if (IS_ERR(bq2515x->ce_gpio)) {
+		ret = PTR_ERR(bq2515x->ce_gpio);
+		dev_err(bq2515x->dev, "Failed to get ce");
+		return ret;
+	}
+
+	return 0;
+}
+
+static bool bq2515x_volatile_register(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BQ2515X_STAT0 ... BQ2515X_FLAG3:
+	case BQ2515X_ADC_VBAT_M ... BQ2515X_ADC_IIN_L:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct regmap_config bq25150_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register		= BQ2515X_DEVICE_ID,
+	.reg_defaults		= bq25150_reg_defaults,
+	.num_reg_defaults	= ARRAY_SIZE(bq25150_reg_defaults),
+	.cache_type		= REGCACHE_RBTREE,
+	.volatile_reg		= bq2515x_volatile_register,
+};
+
+static const struct regmap_config bq25155_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register		= BQ2515X_DEVICE_ID,
+	.reg_defaults		= bq25155_reg_defaults,
+	.num_reg_defaults	= ARRAY_SIZE(bq25155_reg_defaults),
+	.cache_type		= REGCACHE_RBTREE,
+	.volatile_reg		= bq2515x_volatile_register,
+};
+
+static int bq2515x_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct bq2515x_device *bq2515x;
+	struct power_supply_config charger_cfg = {};
+	int ret;
+
+	bq2515x = devm_kzalloc(dev, sizeof(*bq2515x), GFP_KERNEL);
+	if (!bq2515x)
+		return -ENOMEM;
+
+	bq2515x->dev = dev;
+
+	strncpy(bq2515x->model_name, id->name, I2C_NAME_SIZE);
+
+	bq2515x->device_id = id->driver_data;
+
+	switch (bq2515x->device_id) {
+	case BQ25150:
+		bq2515x->regmap = devm_regmap_init_i2c(client,
+						&bq25150_regmap_config);
+		break;
+	case BQ25155:
+		bq2515x->regmap = devm_regmap_init_i2c(client,
+						&bq25155_regmap_config);
+		break;
+	}
+
+	if (IS_ERR(bq2515x->regmap)) {
+		dev_err(dev, "failed to allocate register map\n");
+		return PTR_ERR(bq2515x->regmap);
+	}
+
+	i2c_set_clientdata(client, bq2515x);
+
+	charger_cfg.drv_data = bq2515x;
+	charger_cfg.of_node = dev->of_node;
+
+	ret = bq2515x_read_properties(bq2515x);
+	if (ret) {
+		dev_err(dev, "Failed to read device tree properties %d\n",
+									ret);
+		return ret;
+	}
+
+	ret = bq2515x_power_supply_register(bq2515x, dev, charger_cfg);
+	if (ret) {
+		dev_err(dev, "failed to register power supply\n");
+		return ret;
+	}
+
+	ret = bq2515x_hw_init(bq2515x);
+	if (ret) {
+		dev_err(dev, "Cannot initialize the chip\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id bq2515x_i2c_ids[] = {
+	{ "bq25150", BQ25150, },
+	{ "bq25155", BQ25155, },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, bq2515x_i2c_ids);
+
+static const struct of_device_id bq2515x_of_match[] = {
+	{ .compatible = "ti,bq25150", },
+	{ .compatible = "ti,bq25155", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bq2515x_of_match);
+
+static struct i2c_driver bq2515x_driver = {
+	.driver = {
+		.name = "bq2515x-charger",
+		.of_match_table = bq2515x_of_match,
+	},
+	.probe = bq2515x_probe,
+	.id_table = bq2515x_i2c_ids,
+};
+module_i2c_driver(bq2515x_driver);
+
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_AUTHOR("Ricardo Rivera-Matos <r-rivera-matos@ti.com>");
+MODULE_DESCRIPTION("BQ2515X charger driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/power/supply/bq27xxx_battery.c b/drivers/power/supply/bq27xxx_battery.c
index 942c92127b6d56baca175f00a00ea041f53dbbb5..a123f6e21f08a8f05800dda7dcae9f323b1fc066 100644
--- a/drivers/power/supply/bq27xxx_battery.c
+++ b/drivers/power/supply/bq27xxx_battery.c
@@ -18,31 +18,33 @@
  * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  *
  * Datasheets:
- * http://www.ti.com/product/bq27000
- * http://www.ti.com/product/bq27200
- * http://www.ti.com/product/bq27010
- * http://www.ti.com/product/bq27210
- * http://www.ti.com/product/bq27500
- * http://www.ti.com/product/bq27510-g1
- * http://www.ti.com/product/bq27510-g2
- * http://www.ti.com/product/bq27510-g3
- * http://www.ti.com/product/bq27520-g1
- * http://www.ti.com/product/bq27520-g2
- * http://www.ti.com/product/bq27520-g3
- * http://www.ti.com/product/bq27520-g4
- * http://www.ti.com/product/bq27530-g1
- * http://www.ti.com/product/bq27531-g1
- * http://www.ti.com/product/bq27541-g1
- * http://www.ti.com/product/bq27542-g1
- * http://www.ti.com/product/bq27546-g1
- * http://www.ti.com/product/bq27742-g1
- * http://www.ti.com/product/bq27545-g1
- * http://www.ti.com/product/bq27421-g1
- * http://www.ti.com/product/bq27425-g1
- * http://www.ti.com/product/bq27426
- * http://www.ti.com/product/bq27411-g1
- * http://www.ti.com/product/bq27441-g1
- * http://www.ti.com/product/bq27621-g1
+ * https://www.ti.com/product/bq27000
+ * https://www.ti.com/product/bq27200
+ * https://www.ti.com/product/bq27010
+ * https://www.ti.com/product/bq27210
+ * https://www.ti.com/product/bq27500
+ * https://www.ti.com/product/bq27510-g1
+ * https://www.ti.com/product/bq27510-g2
+ * https://www.ti.com/product/bq27510-g3
+ * https://www.ti.com/product/bq27520-g1
+ * https://www.ti.com/product/bq27520-g2
+ * https://www.ti.com/product/bq27520-g3
+ * https://www.ti.com/product/bq27520-g4
+ * https://www.ti.com/product/bq27530-g1
+ * https://www.ti.com/product/bq27531-g1
+ * https://www.ti.com/product/bq27541-g1
+ * https://www.ti.com/product/bq27542-g1
+ * https://www.ti.com/product/bq27546-g1
+ * https://www.ti.com/product/bq27742-g1
+ * https://www.ti.com/product/bq27545-g1
+ * https://www.ti.com/product/bq27421-g1
+ * https://www.ti.com/product/bq27425-g1
+ * https://www.ti.com/product/bq27426
+ * https://www.ti.com/product/bq27411-g1
+ * https://www.ti.com/product/bq27441-g1
+ * https://www.ti.com/product/bq27621-g1
+ * https://www.ti.com/product/bq27z561
+ * https://www.ti.com/product/bq28z610
  */
 
 #include <linux/device.h>
@@ -79,6 +81,11 @@
 #define BQ27000_FLAG_FC		BIT(5)
 #define BQ27000_FLAG_CHGS	BIT(7) /* Charge state flag */
 
+/* BQ27Z561 has different layout for Flags register */
+#define BQ27Z561_FLAG_FDC	BIT(4) /* Battery fully discharged */
+#define BQ27Z561_FLAG_FC		BIT(5) /* Battery fully charged */
+#define BQ27Z561_FLAG_DIS_CH	BIT(6) /* Battery is discharging */
+
 /* control register params */
 #define BQ27XXX_SEALED			0x20
 #define BQ27XXX_SET_CFGUPDATE		0x13
@@ -431,12 +438,52 @@ static u8
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = 0x18,
 		BQ27XXX_DM_REG_ROWS,
-	};
+	},
 #define bq27411_regs bq27421_regs
 #define bq27425_regs bq27421_regs
 #define bq27426_regs bq27421_regs
 #define bq27441_regs bq27421_regs
 #define bq27621_regs bq27421_regs
+	bq27z561_regs[BQ27XXX_REG_MAX] = {
+		[BQ27XXX_REG_CTRL] = 0x00,
+		[BQ27XXX_REG_TEMP] = 0x06,
+		[BQ27XXX_REG_INT_TEMP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_VOLT] = 0x08,
+		[BQ27XXX_REG_AI] = 0x14,
+		[BQ27XXX_REG_FLAGS] = 0x0a,
+		[BQ27XXX_REG_TTE] = 0x16,
+		[BQ27XXX_REG_TTF] = 0x18,
+		[BQ27XXX_REG_TTES] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTECP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_NAC] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_FCC] = 0x12,
+		[BQ27XXX_REG_CYCT] = 0x2a,
+		[BQ27XXX_REG_AE] = 0x22,
+		[BQ27XXX_REG_SOC] = 0x2c,
+		[BQ27XXX_REG_DCAP] = 0x3c,
+		[BQ27XXX_REG_AP] = 0x22,
+		BQ27XXX_DM_REG_ROWS,
+	},
+	bq28z610_regs[BQ27XXX_REG_MAX] = {
+		[BQ27XXX_REG_CTRL] = 0x00,
+		[BQ27XXX_REG_TEMP] = 0x06,
+		[BQ27XXX_REG_INT_TEMP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_VOLT] = 0x08,
+		[BQ27XXX_REG_AI] = 0x14,
+		[BQ27XXX_REG_FLAGS] = 0x0a,
+		[BQ27XXX_REG_TTE] = 0x16,
+		[BQ27XXX_REG_TTF] = 0x18,
+		[BQ27XXX_REG_TTES] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTECP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_NAC] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_FCC] = 0x12,
+		[BQ27XXX_REG_CYCT] = 0x2a,
+		[BQ27XXX_REG_AE] = 0x22,
+		[BQ27XXX_REG_SOC] = 0x2c,
+		[BQ27XXX_REG_DCAP] = 0x3c,
+		[BQ27XXX_REG_AP] = 0x22,
+		BQ27XXX_DM_REG_ROWS,
+	};
 
 static enum power_supply_property bq27000_props[] = {
 	POWER_SUPPLY_PROP_STATUS,
@@ -672,6 +719,44 @@ static enum power_supply_property bq27421_props[] = {
 #define bq27441_props bq27421_props
 #define bq27621_props bq27421_props
 
+static enum power_supply_property bq27z561_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static enum power_supply_property bq28z610_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_POWER_AVG,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
 struct bq27xxx_dm_reg {
 	u8 subclass_id;
 	u8 offset;
@@ -767,11 +852,15 @@ static struct bq27xxx_dm_reg bq27621_dm_regs[] = {
 #define bq27621_dm_regs 0
 #endif
 
+#define bq27z561_dm_regs 0
+#define bq28z610_dm_regs 0
+
 #define BQ27XXX_O_ZERO	0x00000001
 #define BQ27XXX_O_OTDC	0x00000002 /* has OTC/OTD overtemperature flags */
 #define BQ27XXX_O_UTOT  0x00000004 /* has OT overtemperature flag */
 #define BQ27XXX_O_CFGUP	0x00000008
 #define BQ27XXX_O_RAM	0x00000010
+#define BQ27Z561_O_BITS	0x00000020
 
 #define BQ27XXX_DATA(ref, key, opt) {		\
 	.opts = (opt),				\
@@ -816,6 +905,8 @@ static struct {
 	[BQ27426]   = BQ27XXX_DATA(bq27426,   0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM),
 	[BQ27441]   = BQ27XXX_DATA(bq27441,   0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM),
 	[BQ27621]   = BQ27XXX_DATA(bq27621,   0x80008000, BQ27XXX_O_UTOT | BQ27XXX_O_CFGUP | BQ27XXX_O_RAM),
+	[BQ27Z561]  = BQ27XXX_DATA(bq27z561,  0         , BQ27Z561_O_BITS),
+	[BQ28Z610]  = BQ27XXX_DATA(bq28z610,  0         , BQ27Z561_O_BITS),
 };
 
 static DEFINE_MUTEX(bq27xxx_list_lock);
@@ -1551,6 +1642,8 @@ static bool bq27xxx_battery_dead(struct bq27xxx_device_info *di, u16 flags)
 {
 	if (di->opts & BQ27XXX_O_ZERO)
 		return flags & (BQ27000_FLAG_EDV1 | BQ27000_FLAG_EDVF);
+	else if (di->opts & BQ27Z561_O_BITS)
+		return flags & BQ27Z561_FLAG_FDC;
 	else
 		return flags & (BQ27XXX_FLAG_SOC1 | BQ27XXX_FLAG_SOCF);
 }
@@ -1595,6 +1688,7 @@ void bq27xxx_battery_update(struct bq27xxx_device_info *di)
 				cache.time_to_empty_avg = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTECP);
 			if (di->regs[BQ27XXX_REG_TTF] != INVALID_REG_ADDR)
 				cache.time_to_full = bq27xxx_battery_read_time(di, BQ27XXX_REG_TTF);
+
 			cache.charge_full = bq27xxx_battery_read_fcc(di);
 			cache.capacity = bq27xxx_battery_read_soc(di);
 			if (di->regs[BQ27XXX_REG_AE] != INVALID_REG_ADDR)
@@ -1682,6 +1776,13 @@ static int bq27xxx_battery_status(struct bq27xxx_device_info *di,
 			status = POWER_SUPPLY_STATUS_NOT_CHARGING;
 		else
 			status = POWER_SUPPLY_STATUS_DISCHARGING;
+	} else if (di->opts & BQ27Z561_O_BITS) {
+		if (di->cache.flags & BQ27Z561_FLAG_FC)
+			status = POWER_SUPPLY_STATUS_FULL;
+		else if (di->cache.flags & BQ27Z561_FLAG_DIS_CH)
+			status = POWER_SUPPLY_STATUS_DISCHARGING;
+		else
+			status = POWER_SUPPLY_STATUS_CHARGING;
 	} else {
 		if (di->cache.flags & BQ27XXX_FLAG_FC)
 			status = POWER_SUPPLY_STATUS_FULL;
@@ -1710,6 +1811,13 @@ static int bq27xxx_battery_capacity_level(struct bq27xxx_device_info *di,
 			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
 		else
 			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
+	} else if (di->opts & BQ27Z561_O_BITS) {
+		if (di->cache.flags & BQ27Z561_FLAG_FC)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
+		else if (di->cache.flags & BQ27Z561_FLAG_FDC)
+			level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
+		else
+			level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
 	} else {
 		if (di->cache.flags & BQ27XXX_FLAG_FC)
 			level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
diff --git a/drivers/power/supply/bq27xxx_battery_hdq.c b/drivers/power/supply/bq27xxx_battery_hdq.c
index 9aff896c98020f68379c2532f28c7b2f27ddcd93..29771967df2e3b5395b21a1b3121e3613e642969 100644
--- a/drivers/power/supply/bq27xxx_battery_hdq.c
+++ b/drivers/power/supply/bq27xxx_battery_hdq.c
@@ -1,7 +1,7 @@
 /*
  * BQ27xxx battery monitor HDQ/1-wire driver
  *
- * Copyright (C) 2007-2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2007-2017 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
diff --git a/drivers/power/supply/bq27xxx_battery_i2c.c b/drivers/power/supply/bq27xxx_battery_i2c.c
index 2677c38a8a42453c970d90ed3e45572330b7a59f..ab02456d69e54556dbd99e1e6d33a7df5ae6bfd3 100644
--- a/drivers/power/supply/bq27xxx_battery_i2c.c
+++ b/drivers/power/supply/bq27xxx_battery_i2c.c
@@ -1,7 +1,7 @@
 /*
  * BQ27xxx battery monitor I2C driver
  *
- * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015 Texas Instruments Incorporated - https://www.ti.com/
  *	Andrew F. Davis <afd@ti.com>
  *
  * This program is free software; you can redistribute it and/or modify
@@ -253,6 +253,8 @@ static const struct i2c_device_id bq27xxx_i2c_id_table[] = {
 	{ "bq27426", BQ27426 },
 	{ "bq27441", BQ27441 },
 	{ "bq27621", BQ27621 },
+	{ "bq27z561", BQ27Z561 },
+	{ "bq28z610", BQ28Z610 },
 	{},
 };
 MODULE_DEVICE_TABLE(i2c, bq27xxx_i2c_id_table);
@@ -286,6 +288,8 @@ static const struct of_device_id bq27xxx_battery_i2c_of_match_table[] = {
 	{ .compatible = "ti,bq27426" },
 	{ .compatible = "ti,bq27441" },
 	{ .compatible = "ti,bq27621" },
+	{ .compatible = "ti,bq27z561" },
+	{ .compatible = "ti,bq28z610" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, bq27xxx_battery_i2c_of_match_table);
diff --git a/drivers/power/supply/cpcap-battery.c b/drivers/power/supply/cpcap-battery.c
index 6e9392901b0a27c084dcbb6deb5e10be45766fc5..90eba364664b85fb854d3445a70c664499d3b86d 100644
--- a/drivers/power/supply/cpcap-battery.c
+++ b/drivers/power/supply/cpcap-battery.c
@@ -274,7 +274,7 @@ static int cpcap_battery_cc_to_ua(struct cpcap_battery_ddata *ddata,
 /**
  * cpcap_battery_read_accumulated - reads cpcap coulomb counter
  * @ddata: device driver data
- * @regs: coulomb counter values
+ * @ccd: coulomb counter values
  *
  * Based on Motorola mapphone kernel function data_read_regs().
  * Looking at the registers, the coulomb counter seems similar to
diff --git a/drivers/power/supply/da9030_battery.c b/drivers/power/supply/da9030_battery.c
index 88582423b87d40728b36df1ede0e0131989cb615..0deba48d22d31726013e8e047068e928df5a3df1 100644
--- a/drivers/power/supply/da9030_battery.c
+++ b/drivers/power/supply/da9030_battery.c
@@ -172,17 +172,7 @@ static int bat_debug_show(struct seq_file *s, void *data)
 	return 0;
 }
 
-static int debug_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, bat_debug_show, inode->i_private);
-}
-
-static const struct file_operations bat_debug_fops = {
-	.open		= debug_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(bat_debug);
 
 static struct dentry *da9030_bat_create_debugfs(struct da9030_charger *charger)
 {
diff --git a/drivers/power/supply/gpio-charger.c b/drivers/power/supply/gpio-charger.c
index 1b959c7f8b0e6fc854881e091d2d231ad0649aaf..875735d50716bff10fe579a01a817f4612d27212 100644
--- a/drivers/power/supply/gpio-charger.c
+++ b/drivers/power/supply/gpio-charger.c
@@ -112,9 +112,14 @@ static int gpio_charger_get_irq(struct device *dev, void *dev_id,
 	return irq;
 }
 
+/*
+ * The entries will be overwritten by driver's probe routine depending
+ * on the available features. This list ensures, that the array is big
+ * enough for all optional features.
+ */
 static enum power_supply_property gpio_charger_properties[] = {
 	POWER_SUPPLY_PROP_ONLINE,
-	POWER_SUPPLY_PROP_STATUS /* Must always be last in the array. */
+	POWER_SUPPLY_PROP_STATUS,
 };
 
 static int gpio_charger_probe(struct platform_device *pdev)
@@ -128,6 +133,7 @@ static int gpio_charger_probe(struct platform_device *pdev)
 	int charge_status_irq;
 	unsigned long flags;
 	int ret;
+	int num_props = 0;
 
 	if (!pdata && !dev->of_node) {
 		dev_err(dev, "No platform data\n");
@@ -142,13 +148,13 @@ static int gpio_charger_probe(struct platform_device *pdev)
 	 * This will fetch a GPIO descriptor from device tree, ACPI or
 	 * boardfile descriptor tables. It's good to try this first.
 	 */
-	gpio_charger->gpiod = devm_gpiod_get(dev, NULL, GPIOD_IN);
+	gpio_charger->gpiod = devm_gpiod_get_optional(dev, NULL, GPIOD_IN);
 
 	/*
-	 * If this fails and we're not using device tree, try the
-	 * legacy platform data method.
+	 * Fallback to legacy platform data method, if no GPIO is specified
+	 * using boardfile descriptor tables.
 	 */
-	if (IS_ERR(gpio_charger->gpiod) && !dev->of_node) {
+	if (!gpio_charger->gpiod && pdata) {
 		/* Non-DT: use legacy GPIO numbers */
 		if (!gpio_is_valid(pdata->gpio)) {
 			dev_err(dev, "Invalid gpio pin in pdata\n");
@@ -173,17 +179,23 @@ static int gpio_charger_probe(struct platform_device *pdev)
 		return PTR_ERR(gpio_charger->gpiod);
 	}
 
+	if (gpio_charger->gpiod) {
+		gpio_charger_properties[num_props] = POWER_SUPPLY_PROP_ONLINE;
+		num_props++;
+	}
+
 	charge_status = devm_gpiod_get_optional(dev, "charge-status", GPIOD_IN);
-	gpio_charger->charge_status = charge_status;
-	if (IS_ERR(gpio_charger->charge_status))
-		return PTR_ERR(gpio_charger->charge_status);
+	if (IS_ERR(charge_status))
+		return PTR_ERR(charge_status);
+	if (charge_status) {
+		gpio_charger->charge_status = charge_status;
+		gpio_charger_properties[num_props] = POWER_SUPPLY_PROP_STATUS;
+		num_props++;
+	}
 
 	charger_desc = &gpio_charger->charger_desc;
 	charger_desc->properties = gpio_charger_properties;
-	charger_desc->num_properties = ARRAY_SIZE(gpio_charger_properties);
-	/* Remove POWER_SUPPLY_PROP_STATUS from the supported properties. */
-	if (!gpio_charger->charge_status)
-		charger_desc->num_properties -= 1;
+	charger_desc->num_properties = num_props;
 	charger_desc->get_property = gpio_charger_get_property;
 
 	psy_cfg.of_node = dev->of_node;
@@ -269,6 +281,6 @@ static struct platform_driver gpio_charger_driver = {
 module_platform_driver(gpio_charger_driver);
 
 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
-MODULE_DESCRIPTION("Driver for chargers which report their online status through a GPIO");
+MODULE_DESCRIPTION("Driver for chargers only communicating via GPIO(s)");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:gpio-charger");
diff --git a/drivers/power/supply/max17040_battery.c b/drivers/power/supply/max17040_battery.c
index 48aa44665e2f1ac66a3681181a1410945560ecf7..6cb31b9a958ddbf074eb6402a618a86c9709b368 100644
--- a/drivers/power/supply/max17040_battery.c
+++ b/drivers/power/supply/max17040_battery.c
@@ -69,6 +69,9 @@ static int max17040_get_property(struct power_supply *psy,
 	case POWER_SUPPLY_PROP_CAPACITY:
 		val->intval = chip->soc;
 		break;
+	case POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN:
+		val->intval = chip->low_soc_alert;
+		break;
 	default:
 		return -EINVAL;
 	}
@@ -256,19 +259,57 @@ static int max17040_enable_alert_irq(struct max17040_chip *chip)
 	return ret;
 }
 
+static int max17040_prop_writeable(struct power_supply *psy,
+				   enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static int max17040_set_property(struct power_supply *psy,
+			    enum power_supply_property psp,
+			    const union power_supply_propval *val)
+{
+	struct max17040_chip *chip = power_supply_get_drvdata(psy);
+	int ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN:
+		/* alert threshold can be programmed from 1% up to 32% */
+		if ((val->intval < 1) || (val->intval > 32)) {
+			ret = -EINVAL;
+			break;
+		}
+		ret = max17040_set_low_soc_alert(chip->client, val->intval);
+		chip->low_soc_alert = val->intval;
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
 static enum power_supply_property max17040_battery_props[] = {
 	POWER_SUPPLY_PROP_STATUS,
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN,
 };
 
 static const struct power_supply_desc max17040_battery_desc = {
-	.name		= "battery",
-	.type		= POWER_SUPPLY_TYPE_BATTERY,
-	.get_property	= max17040_get_property,
-	.properties	= max17040_battery_props,
-	.num_properties	= ARRAY_SIZE(max17040_battery_props),
+	.name			= "battery",
+	.type			= POWER_SUPPLY_TYPE_BATTERY,
+	.get_property		= max17040_get_property,
+	.set_property		= max17040_set_property,
+	.property_is_writeable  = max17040_prop_writeable,
+	.properties		= max17040_battery_props,
+	.num_properties		= ARRAY_SIZE(max17040_battery_props),
 };
 
 static int max17040_probe(struct i2c_client *client,
diff --git a/drivers/power/supply/max8998_charger.c b/drivers/power/supply/max8998_charger.c
index 9a926c7c0f22ad9e092fd80673493fcd68c78a16..c26023b19f267fc63abaedd614267fb4a5fbe16f 100644
--- a/drivers/power/supply/max8998_charger.c
+++ b/drivers/power/supply/max8998_charger.c
@@ -23,6 +23,7 @@ struct max8998_battery_data {
 static enum power_supply_property max8998_battery_props[] = {
 	POWER_SUPPLY_PROP_PRESENT, /* the presence of battery */
 	POWER_SUPPLY_PROP_ONLINE, /* charger is active or not */
+	POWER_SUPPLY_PROP_STATUS, /* charger is charging/discharging/full */
 };
 
 /* Note that the charger control is done by a current regulator "CHARGER" */
@@ -49,10 +50,28 @@ static int max8998_battery_get_property(struct power_supply *psy,
 		ret = max8998_read_reg(i2c, MAX8998_REG_STATUS2, &reg);
 		if (ret)
 			return ret;
-		if (reg & (1 << 3))
-			val->intval = 0;
-		else
+
+		if (reg & (1 << 5))
 			val->intval = 1;
+		else
+			val->intval = 0;
+
+		break;
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = max8998_read_reg(i2c, MAX8998_REG_STATUS2, &reg);
+		if (ret)
+			return ret;
+
+		if (!(reg & (1 << 5))) {
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		} else {
+			if (reg & (1 << 6))
+				val->intval = POWER_SUPPLY_STATUS_FULL;
+			else if (reg & (1 << 3))
+				val->intval = POWER_SUPPLY_STATUS_CHARGING;
+			else
+				val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		}
 		break;
 	default:
 		return -EINVAL;
diff --git a/drivers/power/supply/power_supply_core.c b/drivers/power/supply/power_supply_core.c
index 90e56736d4794f6cdf68e9aa387857465bf9ae9c..ccbad435ed124e399dc8d5da33462be6ddb7852d 100644
--- a/drivers/power/supply/power_supply_core.c
+++ b/drivers/power/supply/power_supply_core.c
@@ -733,7 +733,7 @@ EXPORT_SYMBOL_GPL(power_supply_put_battery_info);
  * percent
  * @table: Pointer to battery resistance temperature table
  * @table_len: The table length
- * @ocv: Current temperature
+ * @temp: Current temperature
  *
  * This helper function is used to look up battery internal resistance percent
  * according to current temperature value from the resistance temperature table,
diff --git a/drivers/power/supply/power_supply_sysfs.c b/drivers/power/supply/power_supply_sysfs.c
index bc79560229b5143f22f5a18678b56b233a9434e8..3d383086018c5b69c5e17f0c353f34f4fc837e3e 100644
--- a/drivers/power/supply/power_supply_sysfs.c
+++ b/drivers/power/supply/power_supply_sysfs.c
@@ -87,6 +87,7 @@ static const char * const POWER_SUPPLY_CHARGE_TYPE_TEXT[] = {
 	[POWER_SUPPLY_CHARGE_TYPE_STANDARD]	= "Standard",
 	[POWER_SUPPLY_CHARGE_TYPE_ADAPTIVE]	= "Adaptive",
 	[POWER_SUPPLY_CHARGE_TYPE_CUSTOM]	= "Custom",
+	[POWER_SUPPLY_CHARGE_TYPE_LONGLIFE]	= "Long Life",
 };
 
 static const char * const POWER_SUPPLY_HEALTH_TEXT[] = {
@@ -101,6 +102,9 @@ static const char * const POWER_SUPPLY_HEALTH_TEXT[] = {
 	[POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE]   = "Safety timer expire",
 	[POWER_SUPPLY_HEALTH_OVERCURRENT]	    = "Over current",
 	[POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED]  = "Calibration required",
+	[POWER_SUPPLY_HEALTH_WARM]		    = "Warm",
+	[POWER_SUPPLY_HEALTH_COOL]		    = "Cool",
+	[POWER_SUPPLY_HEALTH_HOT]		    = "Hot",
 };
 
 static const char * const POWER_SUPPLY_TECHNOLOGY_TEXT[] = {
@@ -343,7 +347,7 @@ static umode_t power_supply_attr_is_visible(struct kobject *kobj,
 					   struct attribute *attr,
 					   int attrno)
 {
-	struct device *dev = container_of(kobj, struct device, kobj);
+	struct device *dev = kobj_to_dev(kobj);
 	struct power_supply *psy = dev_get_drvdata(dev);
 	umode_t mode = S_IRUSR | S_IRGRP | S_IROTH;
 	int i;
diff --git a/drivers/power/supply/rt5033_battery.c b/drivers/power/supply/rt5033_battery.c
index d8667a9fc49b1ba1ebcdb329b62c219e432e6c07..f330452341f02953189d3328c830c21160d68e95 100644
--- a/drivers/power/supply/rt5033_battery.c
+++ b/drivers/power/supply/rt5033_battery.c
@@ -125,7 +125,7 @@ static int rt5033_battery_probe(struct i2c_client *client,
 
 	battery = devm_kzalloc(&client->dev, sizeof(*battery), GFP_KERNEL);
 	if (!battery)
-		return -EINVAL;
+		return -ENOMEM;
 
 	battery->client = client;
 	battery->regmap = devm_regmap_init_i2c(client,
diff --git a/drivers/power/supply/sbs-battery.c b/drivers/power/supply/sbs-battery.c
index 83b9924033bd56502dc947a1651851b3e049bde6..49c3508a6b799bb4cf2fadc9fad62329ba965660 100644
--- a/drivers/power/supply/sbs-battery.c
+++ b/drivers/power/supply/sbs-battery.c
@@ -51,6 +51,14 @@ enum {
 	REG_CHARGE_VOLTAGE,
 };
 
+#define REG_ADDR_SPEC_INFO		0x1A
+#define SPEC_INFO_VERSION_MASK		GENMASK(7, 4)
+#define SPEC_INFO_VERSION_SHIFT		4
+
+#define SBS_VERSION_1_0			1
+#define SBS_VERSION_1_1			2
+#define SBS_VERSION_1_1_WITH_PEC	3
+
 #define REG_ADDR_MANUFACTURE_DATE	0x1B
 
 /* Battery Mode defines */
@@ -224,14 +232,57 @@ static void sbs_disable_charger_broadcasts(struct sbs_info *chip)
 
 static int sbs_update_presence(struct sbs_info *chip, bool is_present)
 {
+	struct i2c_client *client = chip->client;
+	int retries = chip->i2c_retry_count;
+	s32 ret = 0;
+	u8 version;
+
 	if (chip->is_present == is_present)
 		return 0;
 
 	if (!is_present) {
 		chip->is_present = false;
+		/* Disable PEC when no device is present */
+		client->flags &= ~I2C_CLIENT_PEC;
 		return 0;
 	}
 
+	/* Check if device supports packet error checking and use it */
+	while (retries > 0) {
+		ret = i2c_smbus_read_word_data(client, REG_ADDR_SPEC_INFO);
+		if (ret >= 0)
+			break;
+
+		/*
+		 * Some batteries trigger the detection pin before the
+		 * I2C bus is properly connected. This works around the
+		 * issue.
+		 */
+		msleep(100);
+
+		retries--;
+	}
+
+	if (ret < 0) {
+		dev_dbg(&client->dev, "failed to read spec info: %d\n", ret);
+
+		/* fallback to old behaviour */
+		client->flags &= ~I2C_CLIENT_PEC;
+		chip->is_present = true;
+
+		return ret;
+	}
+
+	version = (ret & SPEC_INFO_VERSION_MASK) >> SPEC_INFO_VERSION_SHIFT;
+
+	if (version == SBS_VERSION_1_1_WITH_PEC)
+		client->flags |= I2C_CLIENT_PEC;
+	else
+		client->flags &= ~I2C_CLIENT_PEC;
+
+	dev_dbg(&client->dev, "PEC: %s\n", (client->flags & I2C_CLIENT_PEC) ?
+		"enabled" : "disabled");
+
 	if (!chip->is_present && is_present && !chip->charger_broadcasts)
 		sbs_disable_charger_broadcasts(chip);
 
@@ -263,8 +314,7 @@ static int sbs_read_word_data(struct i2c_client *client, u8 address)
 	return ret;
 }
 
-static int sbs_read_string_data(struct i2c_client *client, u8 address,
-				char *values)
+static int sbs_read_string_data_fallback(struct i2c_client *client, u8 address, char *values)
 {
 	struct sbs_info *chip = i2c_get_clientdata(client);
 	s32 ret = 0, block_length = 0;
@@ -274,6 +324,9 @@ static int sbs_read_string_data(struct i2c_client *client, u8 address,
 	retries_length = chip->i2c_retry_count;
 	retries_block = chip->i2c_retry_count;
 
+	dev_warn_once(&client->dev, "I2C adapter does not support I2C_FUNC_SMBUS_READ_BLOCK_DATA.\n"
+				    "Fallback method does not support PEC.\n");
+
 	/* Adapter needs to support these two functions */
 	if (!i2c_check_functionality(client->adapter,
 				     I2C_FUNC_SMBUS_BYTE_DATA |
@@ -329,6 +382,38 @@ static int sbs_read_string_data(struct i2c_client *client, u8 address,
 	return ret;
 }
 
+static int sbs_read_string_data(struct i2c_client *client, u8 address, char *values)
+{
+	struct sbs_info *chip = i2c_get_clientdata(client);
+	int retries = chip->i2c_retry_count;
+	int ret = 0;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_BLOCK_DATA)) {
+		bool pec = client->flags & I2C_CLIENT_PEC;
+		client->flags &= ~I2C_CLIENT_PEC;
+		ret = sbs_read_string_data_fallback(client, address, values);
+		if (pec)
+			client->flags |= I2C_CLIENT_PEC;
+		return ret;
+	}
+
+	while (retries > 0) {
+		ret = i2c_smbus_read_block_data(client, address, values);
+		if (ret >= 0)
+			break;
+		retries--;
+	}
+
+	if (ret < 0) {
+		dev_dbg(&client->dev, "failed to read block 0x%x: %d\n", address, ret);
+		return ret;
+	}
+
+	/* add string termination */
+	values[ret] = '\0';
+	return ret;
+}
+
 static int sbs_write_word_data(struct i2c_client *client, u8 address,
 	u16 value)
 {
diff --git a/drivers/power/supply/sc27xx_fuel_gauge.c b/drivers/power/supply/sc27xx_fuel_gauge.c
index be42e814ea34b4b94f79c4680dfe768e25656375..9c627618c22499fa7e8815af34d0cc9692c1591d 100644
--- a/drivers/power/supply/sc27xx_fuel_gauge.c
+++ b/drivers/power/supply/sc27xx_fuel_gauge.c
@@ -5,6 +5,7 @@
 #include <linux/iio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
+#include <linux/math64.h>
 #include <linux/module.h>
 #include <linux/nvmem-consumer.h>
 #include <linux/of.h>
@@ -133,14 +134,14 @@ static const char * const sc27xx_charger_supply_name[] = {
 	"sc2723_charger",
 };
 
-static int sc27xx_fgu_adc_to_current(struct sc27xx_fgu_data *data, int adc)
+static int sc27xx_fgu_adc_to_current(struct sc27xx_fgu_data *data, s64 adc)
 {
-	return DIV_ROUND_CLOSEST(adc * 1000, data->cur_1000ma_adc);
+	return DIV_S64_ROUND_CLOSEST(adc * 1000, data->cur_1000ma_adc);
 }
 
-static int sc27xx_fgu_adc_to_voltage(struct sc27xx_fgu_data *data, int adc)
+static int sc27xx_fgu_adc_to_voltage(struct sc27xx_fgu_data *data, s64 adc)
 {
-	return DIV_ROUND_CLOSEST(adc * 1000, data->vol_1000mv_adc);
+	return DIV_S64_ROUND_CLOSEST(adc * 1000, data->vol_1000mv_adc);
 }
 
 static int sc27xx_fgu_voltage_to_adc(struct sc27xx_fgu_data *data, int vol)
diff --git a/drivers/power/supply/test_power.c b/drivers/power/supply/test_power.c
index b3c05ff05783fb64494d9e09075ac0c1cde1eafd..04acd76bbaa1261aa0d5a34e83bb8ecf64a96add 100644
--- a/drivers/power/supply/test_power.c
+++ b/drivers/power/supply/test_power.c
@@ -34,7 +34,7 @@ static int battery_technology		= POWER_SUPPLY_TECHNOLOGY_LION;
 static int battery_capacity		= 50;
 static int battery_voltage		= 3300;
 static int battery_charge_counter	= -1000;
-static int battery_current		= 1600;
+static int battery_current		= -1600;
 
 static bool module_initialized;
 
diff --git a/drivers/power/supply/wilco-charger.c b/drivers/power/supply/wilco-charger.c
index b3c6d7cdd731818c6e011bba9c5826b82fd3697d..98ade073ef05fec46a804126f7635adfc30cd1e0 100644
--- a/drivers/power/supply/wilco-charger.c
+++ b/drivers/power/supply/wilco-charger.c
@@ -27,6 +27,7 @@ enum charge_mode {
 	CHARGE_MODE_AC = 3,	/* Mostly AC use, used for Trickle */
 	CHARGE_MODE_AUTO = 4,	/* Used for Adaptive */
 	CHARGE_MODE_CUSTOM = 5,	/* Used for Custom */
+	CHARGE_MODE_LONGLIFE = 6, /* Used for Long Life */
 };
 
 #define CHARGE_LOWER_LIMIT_MIN	50
@@ -48,6 +49,8 @@ static int psp_val_to_charge_mode(int psp_val)
 		return CHARGE_MODE_AUTO;
 	case POWER_SUPPLY_CHARGE_TYPE_CUSTOM:
 		return CHARGE_MODE_CUSTOM;
+	case POWER_SUPPLY_CHARGE_TYPE_LONGLIFE:
+		return CHARGE_MODE_LONGLIFE;
 	default:
 		return -EINVAL;
 	}
@@ -67,6 +70,8 @@ static int charge_mode_to_psp_val(enum charge_mode mode)
 		return POWER_SUPPLY_CHARGE_TYPE_ADAPTIVE;
 	case CHARGE_MODE_CUSTOM:
 		return POWER_SUPPLY_CHARGE_TYPE_CUSTOM;
+	case CHARGE_MODE_LONGLIFE:
+		return POWER_SUPPLY_CHARGE_TYPE_LONGLIFE;
 	default:
 		return -EINVAL;
 	}
diff --git a/include/linux/math64.h b/include/linux/math64.h
index d097119419e64bd59e6441efc84d47296c2fd898..3381d9e33c4e19af40b15845e047aa65148ece85 100644
--- a/include/linux/math64.h
+++ b/include/linux/math64.h
@@ -281,4 +281,23 @@ u64 mul_u64_u64_div_u64(u64 a, u64 mul, u64 div);
 #define DIV64_U64_ROUND_CLOSEST(dividend, divisor)	\
 	({ u64 _tmp = (divisor); div64_u64((dividend) + _tmp / 2, _tmp); })
 
+/*
+ * DIV_S64_ROUND_CLOSEST - signed 64bit divide with 32bit divisor rounded to nearest integer
+ * @dividend: signed 64bit dividend
+ * @divisor: signed 32bit divisor
+ *
+ * Divide signed 64bit dividend by signed 32bit divisor
+ * and round to closest integer.
+ *
+ * Return: dividend / divisor rounded to nearest integer
+ */
+#define DIV_S64_ROUND_CLOSEST(dividend, divisor)(	\
+{							\
+	s64 __x = (dividend);				\
+	s32 __d = (divisor);				\
+	((__x > 0) == (__d > 0)) ?			\
+		div_s64((__x + (__d / 2)), __d) :	\
+		div_s64((__x - (__d / 2)), __d);	\
+}							\
+)
 #endif /* _LINUX_MATH64_H */
diff --git a/include/linux/power/bq2415x_charger.h b/include/linux/power/bq2415x_charger.h
index 4ca08321e2516b5e0fe5a527ebc8a1e301265eb9..f3c267f2a467a88ee7d4928752fa7e4914094d1d 100644
--- a/include/linux/power/bq2415x_charger.h
+++ b/include/linux/power/bq2415x_charger.h
@@ -14,8 +14,8 @@
  * value is -1 then default chip value (specified in datasheet) will be
  * used.
  *
- * Value resistor_sense is needed for for configuring charge and
- * termination current. It it is less or equal to zero, configuring charge
+ * Value resistor_sense is needed for configuring charge and
+ * termination current. If it is less or equal to zero, configuring charge
  * and termination current will not be possible.
  *
  * For automode support is needed to provide name of power supply device
diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h
index 507c5e214c42412da075442b260ad002e7fcb766..987d9652aa4e74d44e6e72a0cf3b0d2b010c404f 100644
--- a/include/linux/power/bq27xxx_battery.h
+++ b/include/linux/power/bq27xxx_battery.h
@@ -30,6 +30,8 @@ enum bq27xxx_chip {
 	BQ27426,
 	BQ27441,
 	BQ27621,
+	BQ27Z561,
+	BQ28Z610,
 };
 
 struct bq27xxx_device_info;
diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h
index ac1345a48ad051737ed2355f94e68fbaae9e2131..97cc4b85bf6126115dc97eb580463e43725eed64 100644
--- a/include/linux/power_supply.h
+++ b/include/linux/power_supply.h
@@ -48,6 +48,7 @@ enum {
 	POWER_SUPPLY_CHARGE_TYPE_STANDARD,	/* normal speed */
 	POWER_SUPPLY_CHARGE_TYPE_ADAPTIVE,	/* dynamically adjusted speed */
 	POWER_SUPPLY_CHARGE_TYPE_CUSTOM,	/* use CHARGE_CONTROL_* props */
+	POWER_SUPPLY_CHARGE_TYPE_LONGLIFE,	/* slow speed, longer life */
 };
 
 enum {
@@ -62,6 +63,9 @@ enum {
 	POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE,
 	POWER_SUPPLY_HEALTH_OVERCURRENT,
 	POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED,
+	POWER_SUPPLY_HEALTH_WARM,
+	POWER_SUPPLY_HEALTH_COOL,
+	POWER_SUPPLY_HEALTH_HOT,
 };
 
 enum {