Merge tag 'ib-mfd-watchdog-v5.13' into ibs-for-mfd-merged

Immutable branch between MFD and Watchdog due for the v5.13 merge window

Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd9576-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD9576MUF and BD9573MUF Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD9576MUF and BD9573MUF are power management ICs primarily intended for
+  powering the R-Car series processors.
+  The IC provides 6 power outputs with configurable sequencing and safety
+  monitoring. A watchdog logic with slow ping/windowed modes is also included.
+
+properties:
+  compatible:
+    enum:
+      - rohm,bd9576
+      - rohm,bd9573
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  rohm,vout1-en-low:
+    description:
+      BD9576 and BD9573 VOUT1 regulator enable state can be individually
+      controlled by a GPIO. This is dictated by state of vout1-en pin during
+      the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
+      enable sate is controlled via this pin. Set this property if vout1-en
+      is wired to be down at PMIC start-up.
+    type: boolean
+
+  rohm,vout1-en-gpios:
+    description:
+      GPIO specifier to specify the GPIO connected to vout1-en for vout1 ON/OFF
+      state control.
+    maxItems: 1
+
+  rohm,ddr-sel-low:
+    description:
+      The BD9576 and BD9573 output voltage for DDR can be selected by setting
+      the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
+    type: boolean
+
+  rohm,watchdog-enable-gpios:
+    description: The GPIO line used to enable the watchdog.
+    maxItems: 1
+
+  rohm,watchdog-ping-gpios:
+    description: The GPIO line used to ping the watchdog.
+    maxItems: 1
+
+  rohm,hw-timeout-ms:
+    maxItems: 2
+    description:
+      Watchog timeout in milliseconds. If single value is given it is
+      the maximum timeout. Eg. if pinging watchdog is not done within this time
+      limit the watchdog will be triggered. If two values are given watchdog
+      is configured in "window mode". Then first value is limit for short-ping
+      Eg. if watchdog is pinged sooner than that the watchdog will trigger.
+      When two values is given the second value is the maximum timeout.
+      # (HW) minimum for short timeout is 2ms, maximum 220 ms.
+      # (HW) minimum for max timeout is 4ms, maximum 4416 ms.
+
+  regulators:
+    $ref: ../regulator/rohm,bd9576-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+required:
+  - compatible
+  - reg
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/leds/common.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@30 {
+            compatible = "rohm,bd9576";
+            reg = <0x30>;
+            rohm,vout1-en-low;
+            rohm,vout1-en-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+            rohm,ddr-sel-low;
+            rohm,watchdog-enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+            rohm,watchdog-ping-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+            rohm,hw-timeout-ms = <150>, <2300>;
+
+            regulators {
+                boost1: regulator-vd50 {
+                    regulator-name = "VD50";
+                };
+                buck1: regulator-vd18 {
+                    regulator-name = "VD18";
+                };
+                buck2: regulator-vdddr {
+                    regulator-name = "VDDDR";
+                };
+                buck3: regulator-vd10 {
+                    regulator-name = "VD10";
+                };
+                ldo: regulator-voutl1 {
+                    regulator-name = "VOUTL1";
+                };
+                sw: regulator-vouts1 {
+                    regulator-name = "VOUTS1";
+                };
+            };
+        };
+    };

MAINTAINERS

@@ -15478,18 +15478,22 @@ F:	drivers/gpio/gpio-bd71828.c
 F:	drivers/mfd/rohm-bd70528.c
 F:	drivers/mfd/rohm-bd71828.c
 F:	drivers/mfd/rohm-bd718x7.c
+F:	drivers/mfd/rohm-bd9576.c
 F:	drivers/power/supply/bd70528-charger.c
 F:	drivers/regulator/bd70528-regulator.c
 F:	drivers/regulator/bd71815-regulator.c
 F:	drivers/regulator/bd71828-regulator.c
 F:	drivers/regulator/bd718x7-regulator.c
+F:	drivers/regulator/bd9576-regulator.c
 F:	drivers/regulator/rohm-regulator.c
 F:	drivers/rtc/rtc-bd70528.c
 F:	drivers/watchdog/bd70528_wdt.c
+F:	drivers/watchdog/bd9576_wdt.c
 F:	include/linux/mfd/rohm-bd70528.h
 F:	include/linux/mfd/rohm-bd71815.h
 F:	include/linux/mfd/rohm-bd71828.h
 F:	include/linux/mfd/rohm-bd718x7.h
+F:	include/linux/mfd/rohm-bd957x.h
 F:	include/linux/mfd/rohm-generic.h
 F:	include/linux/mfd/rohm-shared.h

drivers/mfd/Kconfig

@@ -2001,6 +2001,17 @@ config MFD_ROHM_BD71828
 	  also a single-cell linear charger, a Coulomb counter, a real-time
 	  clock (RTC), GPIOs and a 32.768 kHz clock gate.
 
+config MFD_ROHM_BD957XMUF
+	tristate "ROHM BD9576MUF and BD9573MUF Power Management ICs"
+	depends on I2C=y
+	depends on OF
+	select REGMAP_I2C
+	select MFD_CORE
+	help
+	  Select this option to get support for the ROHM BD9576MUF and
+	  BD9573MUF Power Management ICs. BD9576 and BD9573 are primarily
+	  designed to be used to power R-Car series processors.
+
 config MFD_STM32_LPTIMER
 	tristate "Support for STM32 Low-Power Timer"
 	depends on (ARCH_STM32 && OF) || COMPILE_TEST

drivers/mfd/Makefile

@@ -262,6 +262,7 @@ obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
 obj-$(CONFIG_MFD_ROHM_BD70528)	+= rohm-bd70528.o
 obj-$(CONFIG_MFD_ROHM_BD71828)	+= rohm-bd71828.o
 obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
+obj-$(CONFIG_MFD_ROHM_BD957XMUF)	+= rohm-bd9576.o
 obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
 obj-$(CONFIG_MFD_KHADAS_MCU) 	+= khadas-mcu.o
 obj-$(CONFIG_MFD_ACER_A500_EC)	+= acer-ec-a500.o

drivers/mfd/rohm-bd9576.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2021 ROHM Semiconductors
+ *
+ * ROHM BD9576MUF and BD9573MUF PMIC driver
+ */
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rohm-bd957x.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+enum {
+	BD957X_REGULATOR_CELL,
+	BD957X_WDT_CELL,
+};
+
+/*
+ * Due to the BD9576MUF nasty IRQ behaiour we don't always populate IRQs.
+ * These will be added to regulator resources only if IRQ information for the
+ * PMIC is populated in device-tree.
+ */
+static const struct resource bd9576_regulator_irqs[] = {
+	DEFINE_RES_IRQ_NAMED(BD9576_INT_THERM, "bd9576-temp"),
+	DEFINE_RES_IRQ_NAMED(BD9576_INT_OVD, "bd9576-ovd"),
+	DEFINE_RES_IRQ_NAMED(BD9576_INT_UVD, "bd9576-uvd"),
+};
+
+static struct mfd_cell bd9573_mfd_cells[] = {
+	[BD957X_REGULATOR_CELL]	= { .name = "bd9573-regulator", },
+	[BD957X_WDT_CELL]	= { .name = "bd9576-wdt", },
+};
+
+static struct mfd_cell bd9576_mfd_cells[] = {
+	[BD957X_REGULATOR_CELL]	= { .name = "bd9576-regulator", },
+	[BD957X_WDT_CELL]	= { .name = "bd9576-wdt", },
+};
+
+static const struct regmap_range volatile_ranges[] = {
+	regmap_reg_range(BD957X_REG_SMRB_ASSERT, BD957X_REG_SMRB_ASSERT),
+	regmap_reg_range(BD957X_REG_PMIC_INTERNAL_STAT,
+			 BD957X_REG_PMIC_INTERNAL_STAT),
+	regmap_reg_range(BD957X_REG_INT_THERM_STAT, BD957X_REG_INT_THERM_STAT),
+	regmap_reg_range(BD957X_REG_INT_OVP_STAT, BD957X_REG_INT_SYS_STAT),
+	regmap_reg_range(BD957X_REG_INT_MAIN_STAT, BD957X_REG_INT_MAIN_STAT),
+};
+
+static const struct regmap_access_table volatile_regs = {
+	.yes_ranges = &volatile_ranges[0],
+	.n_yes_ranges = ARRAY_SIZE(volatile_ranges),
+};
+
+static struct regmap_config bd957x_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.volatile_table = &volatile_regs,
+	.max_register = BD957X_MAX_REGISTER,
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static struct regmap_irq bd9576_irqs[] = {
+	REGMAP_IRQ_REG(BD9576_INT_THERM, 0, BD957X_MASK_INT_MAIN_THERM),
+	REGMAP_IRQ_REG(BD9576_INT_OVP, 0, BD957X_MASK_INT_MAIN_OVP),
+	REGMAP_IRQ_REG(BD9576_INT_SCP, 0, BD957X_MASK_INT_MAIN_SCP),
+	REGMAP_IRQ_REG(BD9576_INT_OCP, 0, BD957X_MASK_INT_MAIN_OCP),
+	REGMAP_IRQ_REG(BD9576_INT_OVD, 0, BD957X_MASK_INT_MAIN_OVD),
+	REGMAP_IRQ_REG(BD9576_INT_UVD, 0, BD957X_MASK_INT_MAIN_UVD),
+	REGMAP_IRQ_REG(BD9576_INT_UVP, 0, BD957X_MASK_INT_MAIN_UVP),
+	REGMAP_IRQ_REG(BD9576_INT_SYS, 0, BD957X_MASK_INT_MAIN_SYS),
+};
+
+static struct regmap_irq_chip bd9576_irq_chip = {
+	.name = "bd9576_irq",
+	.irqs = &bd9576_irqs[0],
+	.num_irqs = ARRAY_SIZE(bd9576_irqs),
+	.status_base = BD957X_REG_INT_MAIN_STAT,
+	.mask_base = BD957X_REG_INT_MAIN_MASK,
+	.ack_base = BD957X_REG_INT_MAIN_STAT,
+	.init_ack_masked = true,
+	.num_regs = 1,
+	.irq_reg_stride = 1,
+};
+
+static int bd957x_i2c_probe(struct i2c_client *i2c,
+			     const struct i2c_device_id *id)
+{
+	int ret;
+	struct regmap *regmap;
+	struct mfd_cell *cells;
+	int num_cells;
+	unsigned long chip_type;
+	struct irq_domain *domain;
+	bool usable_irqs;
+
+	chip_type = (unsigned long)of_device_get_match_data(&i2c->dev);
+
+	switch (chip_type) {
+	case ROHM_CHIP_TYPE_BD9576:
+		cells = bd9576_mfd_cells;
+		num_cells = ARRAY_SIZE(bd9576_mfd_cells);
+		usable_irqs = !!i2c->irq;
+		break;
+	case ROHM_CHIP_TYPE_BD9573:
+		cells = bd9573_mfd_cells;
+		num_cells = ARRAY_SIZE(bd9573_mfd_cells);
+		/*
+		 * BD9573 only supports fatal IRQs which we can not handle
+		 * because SoC is going to lose the power.
+		 */
+		usable_irqs = false;
+		break;
+	default:
+		dev_err(&i2c->dev, "Unknown device type");
+		return -EINVAL;
+	}
+
+	regmap = devm_regmap_init_i2c(i2c, &bd957x_regmap);
+	if (IS_ERR(regmap)) {
+		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
+		return PTR_ERR(regmap);
+	}
+
+	/*
+	 * BD9576 behaves badly. It kepts IRQ line asserted for the whole
+	 * duration of detected HW condition (like over temperature). So we
+	 * don't require IRQ to be populated.
+	 * If IRQ information is not given, then we mask all IRQs and do not
+	 * provide IRQ resources to regulator driver - which then just omits
+	 * the notifiers.
+	 */
+	if (usable_irqs) {
+		struct regmap_irq_chip_data *irq_data;
+		struct mfd_cell *regulators;
+
+		regulators = &bd9576_mfd_cells[BD957X_REGULATOR_CELL];
+		regulators->resources = bd9576_regulator_irqs;
+		regulators->num_resources = ARRAY_SIZE(bd9576_regulator_irqs);
+
+		ret = devm_regmap_add_irq_chip(&i2c->dev, regmap, i2c->irq,
+					       IRQF_ONESHOT, 0,
+					       &bd9576_irq_chip, &irq_data);
+		if (ret) {
+			dev_err(&i2c->dev, "Failed to add IRQ chip\n");
+			return ret;
+		}
+		domain = regmap_irq_get_domain(irq_data);
+	} else {
+		ret = regmap_update_bits(regmap, BD957X_REG_INT_MAIN_MASK,
+					 BD957X_MASK_INT_ALL,
+					 BD957X_MASK_INT_ALL);
+		if (ret)
+			return ret;
+		domain = NULL;
+	}
+
+	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, cells,
+				   num_cells, NULL, 0, domain);
+	if (ret)
+		dev_err(&i2c->dev, "Failed to create subdevices\n");
+
+	return ret;
+}
+
+static const struct of_device_id bd957x_of_match[] = {
+	{ .compatible = "rohm,bd9576", .data = (void *)ROHM_CHIP_TYPE_BD9576, },
+	{ .compatible = "rohm,bd9573", .data = (void *)ROHM_CHIP_TYPE_BD9573, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bd957x_of_match);
+
+static struct i2c_driver bd957x_drv = {
+	.driver = {
+		.name = "rohm-bd957x",
+		.of_match_table = bd957x_of_match,
+	},
+	.probe = &bd957x_i2c_probe,
+};
+module_i2c_driver(bd957x_drv);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD9576MUF and BD9573MUF Power Management IC driver");
+MODULE_LICENSE("GPL");

drivers/watchdog/Kconfig

@@ -172,6 +172,19 @@ config BD70528_WATCHDOG
 	  Alternatively say M to compile the driver as a module,
 	  which will be called bd70528_wdt.
 
+config BD957XMUF_WATCHDOG
+	tristate "ROHM BD9576MUF and BD9573MUF PMIC Watchdog"
+	depends on MFD_ROHM_BD957XMUF
+	select WATCHDOG_CORE
+	help
+	  Support for the watchdog in the ROHM BD9576 and BD9573 PMICs.
+	  These PMIC ICs contain watchdog block which can be configured
+	  to toggle reset line if SoC fails to ping watchdog via GPIO.
+
+	  Say Y here to include support for the ROHM BD9576 or BD9573
+	  watchdog. Alternatively say M to compile the driver as a module,
+	  which will be called bd9576_wdt.
+
 config DA9052_WATCHDOG
 	tristate "Dialog DA9052 Watchdog"
 	depends on PMIC_DA9052 || COMPILE_TEST

drivers/watchdog/Makefile

@@ -204,6 +204,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
 
 # Architecture Independent
 obj-$(CONFIG_BD70528_WATCHDOG) += bd70528_wdt.o
+obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
 obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
 obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
 obj-$(CONFIG_DA9062_WATCHDOG) += da9062_wdt.o

drivers/watchdog/bd9576_wdt.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 ROHM Semiconductors
+ *
+ * ROHM BD9576MUF and BD9573MUF Watchdog driver
+ */
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/rohm-bd957x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/watchdog.h>
+
+static bool nowayout;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+		"Watchdog cannot be stopped once started (default=\"false\")");
+
+#define HW_MARGIN_MIN 2
+#define HW_MARGIN_MAX 4416
+#define BD957X_WDT_DEFAULT_MARGIN 4416
+#define WATCHDOG_TIMEOUT 30
+
+struct bd9576_wdt_priv {
+	struct gpio_desc	*gpiod_ping;
+	struct gpio_desc	*gpiod_en;
+	struct device		*dev;
+	struct regmap		*regmap;
+	bool			always_running;
+	struct watchdog_device	wdd;
+};
+
+static void bd9576_wdt_disable(struct bd9576_wdt_priv *priv)
+{
+	gpiod_set_value_cansleep(priv->gpiod_en, 0);
+}
+
+static int bd9576_wdt_ping(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	/* Pulse */
+	gpiod_set_value_cansleep(priv->gpiod_ping, 1);
+	gpiod_set_value_cansleep(priv->gpiod_ping, 0);
+
+	return 0;
+}
+
+static int bd9576_wdt_start(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	gpiod_set_value_cansleep(priv->gpiod_en, 1);
+
+	return bd9576_wdt_ping(wdd);
+}
+
+static int bd9576_wdt_stop(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	if (!priv->always_running)
+		bd9576_wdt_disable(priv);
+	else
+		set_bit(WDOG_HW_RUNNING, &wdd->status);
+
+	return 0;
+}
+
+static const struct watchdog_info bd957x_wdt_ident = {
+	.options	= WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+			  WDIOF_SETTIMEOUT,
+	.identity	= "BD957x Watchdog",
+};
+
+static const struct watchdog_ops bd957x_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= bd9576_wdt_start,
+	.stop		= bd9576_wdt_stop,
+	.ping		= bd9576_wdt_ping,
+};
+
+/* Unit is hundreds of uS */
+#define FASTNG_MIN 23
+
+static int find_closest_fast(int target, int *sel, int *val)
+{
+	int i;
+	int window = FASTNG_MIN;
+
+	for (i = 0; i < 8 && window < target; i++)
+		window <<= 1;
+
+	*val = window;
+	*sel = i;
+
+	if (i == 8)
+		return -EINVAL;
+
+	return 0;
+
+}
+
+static int find_closest_slow_by_fast(int fast_val, int target, int *slowsel)
+{
+	int sel;
+	static const int multipliers[] = {2, 3, 7, 15};
+
+	for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
+	     multipliers[sel] * fast_val < target; sel++)
+		;
+
+	if (sel == ARRAY_SIZE(multipliers))
+		return -EINVAL;
+
+	*slowsel = sel;
+
+	return 0;
+}
+
+static int find_closest_slow(int target, int *slow_sel, int *fast_sel)
+{
+	static const int multipliers[] = {2, 3, 7, 15};
+	int i, j;
+	int val = 0;
+	int window = FASTNG_MIN;
+
+	for (i = 0; i < 8; i++) {
+		for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
+			int slow;
+
+			slow = window * multipliers[j];
+			if (slow >= target && (!val || slow < val)) {
+				val = slow;
+				*fast_sel = i;
+				*slow_sel = j;
+			}
+		}
+		window <<= 1;
+	}
+	if (!val)
+		return -EINVAL;
+
+	return 0;
+}
+
+#define BD957X_WDG_TYPE_WINDOW BIT(5)
+#define BD957X_WDG_TYPE_SLOW 0
+#define BD957X_WDG_TYPE_MASK BIT(5)
+#define BD957X_WDG_NG_RATIO_MASK 0x18
+#define BD957X_WDG_FASTNG_MASK 0x7
+
+static int bd957x_set_wdt_mode(struct bd9576_wdt_priv *priv, int hw_margin,
+			       int hw_margin_min)
+{
+	int ret, fastng, slowng, type, reg, mask;
+	struct device *dev = priv->dev;
+
+	/* convert to 100uS */
+	hw_margin *= 10;
+	hw_margin_min *= 10;
+	if (hw_margin_min) {
+		int min;
+
+		type = BD957X_WDG_TYPE_WINDOW;
+		dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
+		ret = find_closest_fast(hw_margin_min, &fastng, &min);
+		if (ret) {
+			dev_err(dev, "bad WDT window for fast timeout\n");
+			return ret;
+		}
+
+		ret = find_closest_slow_by_fast(min, hw_margin, &slowng);
+		if (ret) {
+			dev_err(dev, "bad WDT window\n");
+			return ret;
+		}
+
+	} else {
+		type = BD957X_WDG_TYPE_SLOW;
+		dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
+		ret = find_closest_slow(hw_margin, &slowng, &fastng);
+		if (ret) {
+			dev_err(dev, "bad WDT window\n");
+			return ret;
+		}
+	}
+
+	slowng <<= ffs(BD957X_WDG_NG_RATIO_MASK) - 1;
+	reg = type | slowng | fastng;
+	mask = BD957X_WDG_TYPE_MASK | BD957X_WDG_NG_RATIO_MASK |
+	       BD957X_WDG_FASTNG_MASK;
+	ret = regmap_update_bits(priv->regmap, BD957X_REG_WDT_CONF,
+				 mask, reg);
+
+	return ret;
+}
+
+static int bd9576_wdt_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->parent->of_node;
+	struct bd9576_wdt_priv *priv;
+	u32 hw_margin[2];
+	u32 hw_margin_max = BD957X_WDT_DEFAULT_MARGIN, hw_margin_min = 0;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	priv->dev = dev;
+	priv->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!priv->regmap) {
+		dev_err(dev, "No regmap found\n");
+		return -ENODEV;
+	}
+
+	priv->gpiod_en = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+						     "rohm,watchdog-enable-gpios",
+						     0, GPIOD_OUT_LOW,
+						     "watchdog-enable");
+	if (IS_ERR(priv->gpiod_en))
+		return dev_err_probe(dev, PTR_ERR(priv->gpiod_en),
+			      "getting watchdog-enable GPIO failed\n");
+
+	priv->gpiod_ping = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+						     "rohm,watchdog-ping-gpios",
+						     0, GPIOD_OUT_LOW,
+						     "watchdog-ping");
+	if (IS_ERR(priv->gpiod_ping))
+		return dev_err_probe(dev, PTR_ERR(priv->gpiod_ping),
+				     "getting watchdog-ping GPIO failed\n");
+
+	ret = of_property_read_variable_u32_array(np, "rohm,hw-timeout-ms",
+						  &hw_margin[0], 1, 2);
+	if (ret < 0 && ret != -EINVAL)
+		return ret;
+
+	if (ret == 1)
+		hw_margin_max = hw_margin[0];
+
+	if (ret == 2) {
+		hw_margin_max = hw_margin[1];
+		hw_margin_min = hw_margin[0];
+	}
+
+	ret = bd957x_set_wdt_mode(priv, hw_margin_max, hw_margin_min);
+	if (ret)
+		return ret;
+
+	priv->always_running = of_property_read_bool(np, "always-running");
+
+	watchdog_set_drvdata(&priv->wdd, priv);
+
+	priv->wdd.info			= &bd957x_wdt_ident;
+	priv->wdd.ops			= &bd957x_wdt_ops;
+	priv->wdd.min_hw_heartbeat_ms	= hw_margin_min;
+	priv->wdd.max_hw_heartbeat_ms	= hw_margin_max;
+	priv->wdd.parent		= dev;
+	priv->wdd.timeout		= WATCHDOG_TIMEOUT;
+
+	watchdog_init_timeout(&priv->wdd, 0, dev);
+	watchdog_set_nowayout(&priv->wdd, nowayout);
+
+	watchdog_stop_on_reboot(&priv->wdd);
+
+	if (priv->always_running)
+		bd9576_wdt_start(&priv->wdd);
+
+	return devm_watchdog_register_device(dev, &priv->wdd);
+}
+
+static struct platform_driver bd9576_wdt_driver = {
+	.driver	= {
+		.name = "bd9576-wdt",
+	},
+	.probe	= bd9576_wdt_probe,
+};
+
+module_platform_driver(bd9576_wdt_driver);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD9576/BD9573 Watchdog driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd9576-wdt");

include/linux/mfd/rohm-bd957x.h

+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2021 ROHM Semiconductors */
+
+#ifndef __LINUX_MFD_BD957X_H__
+#define __LINUX_MFD_BD957X_H__
+
+enum {
+	BD957X_VD50,
+	BD957X_VD18,
+	BD957X_VDDDR,
+	BD957X_VD10,
+	BD957X_VOUTL1,
+	BD957X_VOUTS1,
+};
+
+/*
+ * The BD9576 has own IRQ 'blocks' for:
+ *  - I2C/thermal,
+ *  - Over voltage protection
+ *  - Short-circuit protection
+ *  - Over current protection
+ *  - Over voltage detection
+ *  - Under voltage detection
+ *  - Under voltage protection
+ *  - 'system interrupt'.
+ *
+ * Each of the blocks have a status register giving more accurate IRQ source
+ * information - for example which of the regulators have over-voltage.
+ *
+ * On top of this, there is "main IRQ" status register where each bit indicates
+ * which of sub-blocks have active IRQs. Fine. That would fit regmap-irq main
+ * status handling. Except that:
+ *  - Only some sub-IRQs can be masked.
+ *  - The IRQ informs us about fault-condition, not when fault state changes.
+ *    The IRQ line it is kept asserted until the detected condition is acked
+ *    AND cleared in HW. This is annoying for IRQs like the one informing high
+ *    temperature because if IRQ is not disabled it keeps the CPU in IRQ
+ *    handling loop.
+ *
+ * For now we do just use the main-IRQ register as source for our IRQ
+ * information and bind the regmap-irq to this. We leave fine-grained sub-IRQ
+ * register handling to handlers in sub-devices. The regulator driver shall
+ * read which regulators are source for problem - or if the detected error is
+ * regulator temperature error. The sub-drivers do also handle masking of "sub-
+ * IRQs" if this is supported/needed.
+ *
+ * To overcome the problem with HW keeping IRQ asserted we do call
+ * disable_irq_nosync() from sub-device handler and add a delayed work to
+ * re-enable IRQ roughly 1 second later. This should keep our CPU out of
+ * busy-loop.
+ */
+#define IRQS_SILENT_MS			1000
+
+enum {
+	BD9576_INT_THERM,
+	BD9576_INT_OVP,
+	BD9576_INT_SCP,
+	BD9576_INT_OCP,
+	BD9576_INT_OVD,
+	BD9576_INT_UVD,
+	BD9576_INT_UVP,
+	BD9576_INT_SYS,
+};
+
+#define BD957X_REG_SMRB_ASSERT		0x15
+#define BD957X_REG_PMIC_INTERNAL_STAT	0x20
+#define BD957X_REG_INT_THERM_STAT	0x23
+#define BD957X_REG_INT_THERM_MASK	0x24
+#define BD957X_REG_INT_OVP_STAT		0x25
+#define BD957X_REG_INT_SCP_STAT		0x26
+#define BD957X_REG_INT_OCP_STAT		0x27
+#define BD957X_REG_INT_OVD_STAT		0x28
+#define BD957X_REG_INT_UVD_STAT		0x29
+#define BD957X_REG_INT_UVP_STAT		0x2a
+#define BD957X_REG_INT_SYS_STAT		0x2b
+#define BD957X_REG_INT_SYS_MASK		0x2c
+#define BD957X_REG_INT_MAIN_STAT	0x30
+#define BD957X_REG_INT_MAIN_MASK	0x31
+
+#define UVD_IRQ_VALID_MASK		0x6F
+#define OVD_IRQ_VALID_MASK		0x2F
+
+#define BD957X_MASK_INT_MAIN_THERM	BIT(0)
+#define BD957X_MASK_INT_MAIN_OVP	BIT(1)
+#define BD957X_MASK_INT_MAIN_SCP	BIT(2)
+#define BD957X_MASK_INT_MAIN_OCP	BIT(3)
+#define BD957X_MASK_INT_MAIN_OVD	BIT(4)
+#define BD957X_MASK_INT_MAIN_UVD	BIT(5)
+#define BD957X_MASK_INT_MAIN_UVP	BIT(6)
+#define BD957X_MASK_INT_MAIN_SYS	BIT(7)
+#define BD957X_MASK_INT_ALL		0xff
+
+#define BD957X_REG_WDT_CONF		0x16
+
+#define BD957X_REG_POW_TRIGGER1		0x41
+#define BD957X_REG_POW_TRIGGER2		0x42
+#define BD957X_REG_POW_TRIGGER3		0x43
+#define BD957X_REG_POW_TRIGGER4		0x44
+#define BD957X_REG_POW_TRIGGERL1	0x45
+#define BD957X_REG_POW_TRIGGERS1	0x46
+
+#define BD957X_REGULATOR_EN_MASK	0xff
+#define BD957X_REGULATOR_DIS_VAL	0xff
+
+#define BD957X_VSEL_REG_MASK		0xff
+
+#define BD957X_MASK_VOUT1_TUNE		0x87
+#define BD957X_MASK_VOUT2_TUNE		0x87
+#define BD957X_MASK_VOUT3_TUNE		0x1f
+#define BD957X_MASK_VOUT4_TUNE		0x1f
+#define BD957X_MASK_VOUTL1_TUNE		0x87
+
+#define BD957X_REG_VOUT1_TUNE		0x50
+#define BD957X_REG_VOUT2_TUNE		0x53
+#define BD957X_REG_VOUT3_TUNE		0x56
+#define BD957X_REG_VOUT4_TUNE		0x59
+#define BD957X_REG_VOUTL1_TUNE		0x5c
+
+#define BD9576_REG_VOUT1_OVD		0x51
+#define BD9576_REG_VOUT1_UVD		0x52
+#define BD9576_REG_VOUT2_OVD		0x54
+#define BD9576_REG_VOUT2_UVD		0x55
+#define BD9576_REG_VOUT3_OVD		0x57
+#define BD9576_REG_VOUT3_UVD		0x58
+#define BD9576_REG_VOUT4_OVD		0x5a
+#define BD9576_REG_VOUT4_UVD		0x5b
+#define BD9576_REG_VOUTL1_OVD		0x5d
+#define BD9576_REG_VOUTL1_UVD		0x5e
+
+#define BD9576_MASK_XVD			0x7f
+
+#define BD9576_REG_VOUT1S_OCW		0x5f
+#define BD9576_REG_VOUT1S_OCP		0x60
+
+#define BD9576_MASK_VOUT1S_OCW		0x3f
+#define BD9576_MASK_VOUT1S_OCP		0x3f
+
+#define BD957X_MAX_REGISTER		0x61
+
+#endif

include/linux/mfd/rohm-generic.h

@@ -9,7 +9,9 @@
 
 enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD9571,
+	ROHM_CHIP_TYPE_BD9573,
 	ROHM_CHIP_TYPE_BD9574,
+	ROHM_CHIP_TYPE_BD9576,
 	ROHM_CHIP_TYPE_BD70528,
 	ROHM_CHIP_TYPE_BD71815,
 	ROHM_CHIP_TYPE_BD71828,