Commit 185095fb authored by Bruce Allan's avatar Bruce Allan Committed by Jeff Kirsher
Browse files

e1000e: use more informative logging macros when netdev not yet registered



Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: default avatarEthan Zhao <ethan.kernel@gmail.com>
Signed-off-by: default avatarBruce Allan <bruce.w.allan@intel.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 04502430
......@@ -6238,7 +6238,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
}
if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
e_info("PHY reset is blocked due to SOL/IDER session.\n");
dev_info(&pdev->dev,
"PHY reset is blocked due to SOL/IDER session.\n");
/* Set initial default active device features */
netdev->features = (NETIF_F_SG |
......@@ -6288,7 +6289,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
break;
if (i == 2) {
e_err("The NVM Checksum Is Not Valid\n");
dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n");
err = -EIO;
goto err_eeprom;
}
......@@ -6298,13 +6299,15 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
/* copy the MAC address */
if (e1000e_read_mac_addr(&adapter->hw))
e_err("NVM Read Error while reading MAC address\n");
dev_err(&pdev->dev,
"NVM Read Error while reading MAC address\n");
memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
if (!is_valid_ether_addr(netdev->perm_addr)) {
e_err("Invalid MAC Address: %pM\n", netdev->perm_addr);
dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
netdev->perm_addr);
err = -EIO;
goto err_eeprom;
}
......
......@@ -199,16 +199,19 @@ static int __devinit e1000_validate_option(unsigned int *value,
case enable_option:
switch (*value) {
case OPTION_ENABLED:
e_info("%s Enabled\n", opt->name);
dev_info(&adapter->pdev->dev, "%s Enabled\n",
opt->name);
return 0;
case OPTION_DISABLED:
e_info("%s Disabled\n", opt->name);
dev_info(&adapter->pdev->dev, "%s Disabled\n",
opt->name);
return 0;
}
break;
case range_option:
if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
e_info("%s set to %i\n", opt->name, *value);
dev_info(&adapter->pdev->dev, "%s set to %i\n",
opt->name, *value);
return 0;
}
break;
......@@ -220,7 +223,8 @@ static int __devinit e1000_validate_option(unsigned int *value,
ent = &opt->arg.l.p[i];
if (*value == ent->i) {
if (ent->str[0] != '\0')
e_info("%s\n", ent->str);
dev_info(&adapter->pdev->dev, "%s\n",
ent->str);
return 0;
}
}
......@@ -230,8 +234,8 @@ static int __devinit e1000_validate_option(unsigned int *value,
BUG();
}
e_info("Invalid %s value specified (%i) %s\n", opt->name, *value,
opt->err);
dev_info(&adapter->pdev->dev, "Invalid %s value specified (%i) %s\n",
opt->name, *value, opt->err);
*value = opt->def;
return -1;
}
......@@ -251,8 +255,10 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter)
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
e_notice("Warning: no configuration for board #%i\n", bd);
e_notice("Using defaults for all values\n");
dev_notice(&adapter->pdev->dev,
"Warning: no configuration for board #%i\n", bd);
dev_notice(&adapter->pdev->dev,
"Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
......@@ -366,27 +372,32 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter)
* default values
*/
if (adapter->itr > 4)
e_info("%s set to default %d\n", opt.name,
adapter->itr);
dev_info(&adapter->pdev->dev,
"%s set to default %d\n", opt.name,
adapter->itr);
}
adapter->itr_setting = adapter->itr;
switch (adapter->itr) {
case 0:
e_info("%s turned off\n", opt.name);
dev_info(&adapter->pdev->dev, "%s turned off\n",
opt.name);
break;
case 1:
e_info("%s set to dynamic mode\n", opt.name);
dev_info(&adapter->pdev->dev,
"%s set to dynamic mode\n", opt.name);
adapter->itr = 20000;
break;
case 3:
e_info("%s set to dynamic conservative mode\n",
opt.name);
dev_info(&adapter->pdev->dev,
"%s set to dynamic conservative mode\n",
opt.name);
adapter->itr = 20000;
break;
case 4:
e_info("%s set to simplified (2000-8000 ints) mode\n",
opt.name);
dev_info(&adapter->pdev->dev,
"%s set to simplified (2000-8000 ints) mode\n",
opt.name);
break;
default:
/*
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment