Commit 80ee72e7 authored by Chen-Yu Tsai's avatar Chen-Yu Tsai Committed by Maxime Ripard
Browse files

ARM: dts: sunxi: Explicitly enable pull-ups for MMC pins



In the past, all the MMC pins had

	allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.

Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: default avatarChen-Yu Tsai <wens@csie.org>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 1edcd36f
......@@ -1023,6 +1023,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
......
......@@ -582,6 +582,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc2_pins_a: mmc2@0 {
......
......@@ -547,6 +547,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
......@@ -554,6 +555,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_pins_a: mmc2@0 {
......@@ -571,6 +573,7 @@
"PC24";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
mmc3_8bit_emmc_pins: mmc3@1 {
......@@ -580,6 +583,7 @@
"PC24";
function = "mmc3";
drive-strength = <40>;
bias-pull-up;
};
uart0_pins_a: uart0@0 {
......
......@@ -1179,6 +1179,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
......@@ -1200,6 +1201,7 @@
"PI7", "PI8", "PI9";
function = "mmc3";
drive-strength = <30>;
bias-pull-up;
};
ps20_pins_a: ps20@0 {
......
......@@ -293,6 +293,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
......@@ -300,6 +301,7 @@
"PG3", "PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
......@@ -309,6 +311,7 @@
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
pwm0_pins: pwm0 {
......
......@@ -171,6 +171,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
uart0_pins_a: uart0@0 {
......
......@@ -348,6 +348,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin: mmc0_cd_pin@0 {
......@@ -361,6 +362,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
......@@ -370,6 +372,7 @@
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
spi0_pins: spi0 {
......
......@@ -696,6 +696,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins: mmc1 {
......@@ -703,6 +704,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
......@@ -712,6 +714,7 @@
"PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
uart0_pins_a: uart0@0 {
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment