Commit 5bb053be authored by Linus Torvalds's avatar Linus Torvalds

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Support offloading wireless authentication to userspace via
    NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.

 2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
    Setup and cleanup of namespaces now all run asynchronously and thus
    performance is significantly increased.

 3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
    Streiff.

 4) Support zerocopy on RDS sockets, from Sowmini Varadhan.

 5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
    Borkmann.

 6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
    Chevallier.

 7) Support grafting of child qdiscs in mlxsw driver, from Nogah
    Frankel.

 8) Add packet forwarding tests to selftests, from Ido Schimmel.

 9) Deal with sub-optimal GSO packets better in BBR congestion control,
    from Eric Dumazet.

10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.

11) Add path MTU tests to selftests, from Stefano Brivio.

12) Various bits of IPSEC offloading support for mlx5, from Aviad
    Yehezkel, Yossi Kuperman, and Saeed Mahameed.

13) Support RSS spreading on ntuple filters in SFC driver, from Edward
    Cree.

14) Lots of sockmap work from John Fastabend. Applications can use eBPF
    to filter sendmsg and sendpage operations.

15) In-kernel receive TLS support, from Dave Watson.

16) Add XDP support to ixgbevf, this is significant because it should
    allow optimized XDP usage in various cloud environments. From Tony
    Nguyen.

17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
    Venkataramanan et al.

18) IP fragmentation match offload support in nfp driver, from Pieter
    Jansen van Vuuren.

19) Support XDP redirect in i40e driver, from Björn Töpel.

20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
    tracepoints in their raw form, from Alexei Starovoitov.

21) Lots of striding RQ improvements to mlx5 driver with many
    performance improvements, from Tariq Toukan.

22) Use rhashtable for inet frag reassembly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
  net: mvneta: improve suspend/resume
  net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
  ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
  net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
  net: bgmac: Correctly annotate register space
  route: check sysctl_fib_multipath_use_neigh earlier than hash
  fix typo in command value in drivers/net/phy/mdio-bitbang.
  sky2: Increase D3 delay to sky2 stops working after suspend
  net/mlx5e: Set EQE based as default TX interrupt moderation mode
  ibmvnic: Disable irqs before exiting reset from closed state
  net: sched: do not emit messages while holding spinlock
  vlan: also check phy_driver ts_info for vlan's real device
  Bluetooth: Mark expected switch fall-throughs
  Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
  Bluetooth: btrsi: remove unused including <linux/version.h>
  Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
  sh_eth: kill useless check in __sh_eth_get_regs()
  sh_eth: add sh_eth_cpu_data::no_xdfar flag
  ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
  ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
  ...
parents bb2407a7 159f0297

Too many changes to show.

To preserve performance only 1000 of 1000+ files are displayed.

......@@ -539,6 +539,18 @@ A: Although LLVM IR generation and optimization try to stay architecture
The clang option "-fno-jump-tables" can be used to disable
switch table generation.
- For clang -target bpf, it is guaranteed that pointer or long /
unsigned long types will always have a width of 64 bit, no matter
whether underlying clang binary or default target (or kernel) is
32 bit. However, when native clang target is used, then it will
compile these types based on the underlying architecture's conventions,
meaning in case of 32 bit architecture, pointer or long / unsigned
long types e.g. in BPF context structure will have width of 32 bit
while the BPF LLVM back end still operates in 64 bit. The native
target is mostly needed in tracing for the case of walking pt_regs
or other kernel structures where CPU's register width matters.
Otherwise, clang -target bpf is generally recommended.
You should use default target when:
- Your program includes a header file, e.g., ptrace.h, which eventually
......
......@@ -13,9 +13,18 @@ placed as a child node of an mdio device.
The properties described here are those specific to Marvell devices.
Additional required and optional properties can be found in dsa.txt.
The compatibility string is used only to find an identification register,
which is at a different MDIO base address in different switch families.
- "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
6341, 6350, 6351, 6352
- "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
6190, 6190X, 6191, 6290, 6390, 6390X
Required properties:
- compatible : Should be one of "marvell,mv88e6085" or
"marvell,mv88e6190"
"marvell,mv88e6190" as indicated above
- reg : Address on the MII bus for the switch.
Optional properties:
......
......@@ -10,6 +10,8 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt.
the boot program; should be used in cases where the MAC address assigned to
the device by the boot program is different from the "local-mac-address"
property;
- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used;
- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
the maximum frame size (there's contradiction in the Devicetree
......
* MCR20A IEEE 802.15.4 *
Required properties:
- compatible: should be "nxp,mcr20a"
- spi-max-frequency: maximal bus speed, should be set to a frequency
lower than 9000000 depends sync or async operation mode
- reg: the chipselect index
- interrupts: the interrupt generated by the device. Non high-level
can occur deadlocks while handling isr.
Optional properties:
- rst_b-gpio: GPIO spec for the RST_B pin
Example:
mcr20a@0 {
compatible = "nxp,mcr20a";
spi-max-frequency = <9000000>;
reg = <0>;
interrupts = <17 2>;
interrupt-parent = <&gpio>;
rst_b-gpio = <&gpio 27 1>
};
......@@ -29,6 +29,7 @@ Optional properties for PHY child node:
- reset-gpios : Should specify the gpio for phy reset
- magic-packet : If present, indicates that the hardware supports waking
up via magic packet.
- phy-handle : see ethernet.txt file in the same directory
Examples:
......
......@@ -9,6 +9,7 @@ Required properties on all platforms:
- compatible: Depending on the platform this should be one of:
- "amlogic,meson6-dwmac"
- "amlogic,meson8b-dwmac"
- "amlogic,meson8m2-dwmac"
- "amlogic,meson-gxbb-dwmac"
Additionally "snps,dwmac" and any applicable more
detailed version number described in net/stmmac.txt
......@@ -19,13 +20,13 @@ Required properties on all platforms:
configuration (for example the PRG_ETHERNET register range
on Meson8b and newer)
Required properties on Meson8b and newer:
Required properties on Meson8b, Meson8m2, GXBB and newer:
- clock-names: Should contain the following:
- "stmmaceth" - see stmmac.txt
- "clkin0" - first parent clock of the internal mux
- "clkin1" - second parent clock of the internal mux
Optional properties on Meson8b and newer:
Optional properties on Meson8b, Meson8m2, GXBB and newer:
- amlogic,tx-delay-ns: The internal RGMII TX clock delay (provided
by this driver) in nanoseconds. Allowed values
are: 0ns, 2ns, 4ns, 6ns.
......
* NI XGE Ethernet controller
Required properties:
- compatible: Should be "ni,xge-enet-2.00"
- reg: Address and length of the register set for the device
- interrupts: Should contain tx and rx interrupt
- interrupt-names: Should be "rx" and "tx"
- phy-mode: See ethernet.txt file in the same directory.
- phy-handle: See ethernet.txt file in the same directory.
- nvmem-cells: Phandle of nvmem cell containing the MAC address
- nvmem-cell-names: Should be "address"
Examples (10G generic PHY):
nixge0: ethernet@40000000 {
compatible = "ni,xge-enet-2.00";
reg = <0x40000000 0x6000>;
nvmem-cells = <&eth1_addr>;
nvmem-cell-names = "address";
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "rx", "tx";
interrupt-parent = <&intc>;
phy-mode = "xgmii";
phy-handle = <&ethernet_phy1>;
ethernet_phy1: ethernet-phy@4 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <4>;
};
};
......@@ -7,6 +7,7 @@ Required properties:
- compatible: Must contain one or more of the following:
- "renesas,etheravb-r8a7743" for the R8A7743 SoC.
- "renesas,etheravb-r8a7745" for the R8A7745 SoC.
- "renesas,etheravb-r8a77470" for the R8A77470 SoC.
- "renesas,etheravb-r8a7790" for the R8A7790 SoC.
- "renesas,etheravb-r8a7791" for the R8A7791 SoC.
- "renesas,etheravb-r8a7792" for the R8A7792 SoC.
......
......@@ -33,6 +33,10 @@ Optional Properties:
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
high Tx rate. Must not be present for SFF modules
- maximum-power-milliwatt : Maximum module power consumption
Specifies the maximum power consumption allowable by a module in the
slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W.
Example #1: Direct serdes to SFP connection
sfp_eth3: sfp-eth3 {
......@@ -40,6 +44,7 @@ sfp_eth3: sfp-eth3 {
i2c-bus = <&sfp_1g_i2c>;
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
maximum-power-milliwatt = <1000>;
pinctrl-names = "default";
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
......
......@@ -9,6 +9,7 @@ Required properties:
- "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
- "socionext,uniphier-ld11-ave4" : for LD11 SoC
- "socionext,uniphier-ld20-ave4" : for LD20 SoC
- "socionext,uniphier-pxs3-ave4" : for PXs3 SoC
- reg: Address where registers are mapped and size of region.
- interrupts: Should contain the MAC interrupt.
- phy-mode: See ethernet.txt in the same directory. Allow to choose
......
......@@ -25,6 +25,8 @@ Optional property:
software needs to take when this pin is
strapped in these modes. See data manual
for details.
- ti,clk-output-sel - Muxing option for CLK_OUT pin - see dt-bindings/net/ti-dp83867.h
for applicable values.
Note: ti,min-output-impedance and ti,max-output-impedance are mutually
exclusive. When both properties are present ti,max-output-impedance
......
Intel(R) Ethernet Connection E800 Series Linux Driver
===================================================================
Intel ice Linux driver.
Copyright(c) 2018 Intel Corporation.
Contents
========
- Enabling the driver
- Support
The driver in this release supports Intel's E800 Series of products. For
more information, visit Intel's support page at http://support.intel.com.
Enabling the driver
===================
The driver is enabled via the standard kernel configuration system,
using the make command:
Make oldconfig/silentoldconfig/menuconfig/etc.
The driver is located in the menu structure at:
-> Device Drivers
-> Network device support (NETDEVICES [=y])
-> Ethernet driver support
-> Intel devices
-> Intel(R) Ethernet Connection E800 Series Support
Support
=======
For general information, go to the Intel support website at:
http://support.intel.com
If an issue is identified with the released source code, please email
the maintainer listed in the MAINTAINERS file.
......@@ -133,14 +133,11 @@ min_adv_mss - INTEGER
IP Fragmentation:
ipfrag_high_thresh - INTEGER
Maximum memory used to reassemble IP fragments. When
ipfrag_high_thresh bytes of memory is allocated for this purpose,
the fragment handler will toss packets until ipfrag_low_thresh
is reached. This also serves as a maximum limit to namespaces
different from the initial one.
ipfrag_low_thresh - INTEGER
ipfrag_high_thresh - LONG INTEGER
Maximum memory used to reassemble IP fragments.
ipfrag_low_thresh - LONG INTEGER