This patch adds reset controller driver for MediaTek MIPS platform and
header file for mt7628.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds default pinctrl for uart nodes

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds pinctrl node with default pin state for mt7628an.dtsi.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.

This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.

To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.

With this patch, any amount of data can be read/written in a single xfer
function call.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds clkctrl node for mt7628 and adds clocks property for
some node.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.

Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

This patch adds codes to enable FIFO and disable flow control taken from
ns16550 driver.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.

This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>

Fixes commit 344db3f3

, which added missing bmips dtbs depending on their SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

These are no longer needed.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

BCM63268 uses 4.0 HW nand controller, which is currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

BCM6362 uses old 2.2 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

BCM6328 uses old 2.2 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

BCM6368 uses old 2.1 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.

Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.

Signed-off-by: Ramon Fried <rfried.dev@gmail.com>

- Add Universal Flash Storage (UFS) support

- Add support for HyperBus Memory Controller of TI's J721e
  and AM654 SoCs (Vignesh)

Enable HBMC and HyperFlash in A72 SPL and A72 U-Boot

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks
are automatically detected by CFI flash driver

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Enable SCSI and UFS related configs.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add environment variables to boot kernel from a filesystem contained in
the 2nd UFS LUN. The user can boot from a ufs filesystem just by
entering the following commands.

=> setenv boot ufs
=> boot

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add Support for commands to initialize and configure UFS devices.

TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add TI UFS glue layer and Cadence UFS Host controller DT nodes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add glue layer driver for the controller present on TI's J721E devices.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add Support for the platform driver for the Cadence device present on
TI's J721e device.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:

- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests

Also register this host controller as a SCSI host controller.

Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>