OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Jason Liu <r64343@freescale.com>

The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.

This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>

Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.

Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

this is usefull when writing an UBI image which contains
and UBIFS volume (check README.nand and UBI FAQ for more
details)

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

We've been dropping SoC name from U-Boot prompt as it increase
complexity for automatic testing and makes line longer for no good
reason.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>

This adds a default environment which should be able to support both
3.0.15 from Timesys and upcoming 3.11.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>

Currently we have the following on boot:

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SD/MMC #0, 3V3
DRAM:  128 MiB
MMC:   MXS MMC: 0
Video: MXSFB: 'videomode' variable not set!In:    serial

Break the line of the warning message in order to have a better reading format.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Create a README.mxs file that contains instructions on how to use U-boot for
both MX23 and MX28.

As boot from NAND has only been tested on mx28, make it clear that it only
applies to MX28.

While at it, do some small cleanups for the sake of consistency:
- Use "MX28" instead of "i.MX28"
- Use "section" instead of "chapter" when referring to specific parts of the
reference manual chapters.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Re-structure the sentence a bit so that it can clearer.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

MX28 can boot from SSP0 or SSP1, so it is better not to hardcode the SSP port
in the instructions.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

In order to improve readability keep the text within 80 columns.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>

Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>

Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>

The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Dirk Behme <dirk.behme@gmail.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

The spi clock divisor is of the form x * (2**y),  or  x  << y, where x is
1 to 16, and y is 0 to 15. Note the similarity with floating point numbers.
Convert the desired divisor to the smallest number which is >= desired divisor,
and can be represented in this form. The previous algorithm chose a divisor
which could be almost twice as large as needed.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>

Fix two issues with the calculation of pre_div and post_div:

1. pre_div: While the calculation of pre_div looks correct, to set the
CONREG[15-12] bits pre_div needs to be decremented by 1:

The i.MX 6Dual/6Quad Applications Processor Reference Manual (IMX6DQRM
Rev. 0, 11/2012) states:

CONREG[15-12]: PRE_DIVIDER
0000 Divide by 1
0001 Divide by 2
0010 Divide by 3
...
1101 Divide by 14
1110 Divide by 15
1111 Divide by 16

I.e. if we want to divide by 2, we have to write 1 to CONREG[15-12].

2. In case the post divider becomes necessary, pre_div will be divided by
16. So set pre_div to 16, too. And not 15.

Both issues above are tested using the following examples:

clk_src = 60000000 (60MHz, default i.MX6 ECSPI clock)

a) max_hz == 23000000 (23MHz, max i.MX6 ECSPI read clock)

-> pre_div =  3 (divide by 3 => CONREG[15-12] == 2)
-> post_div = 0 (divide by 1 => CONREG[11- 8] == 0)
               => 60MHz / 3 = 20MHz SPI clock

b) max_hz == 2000000 (2MHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 1  (divide by  2 => CONREG[11- 8] == 1)
               => 60MHz / 32 = 1.875MHz SPI clock

c) max_hz == 1000000 (1MHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 2  (divide by  4 => CONREG[11- 8] == 2)
               => 60MHz / 64 = 937.5kHz SPI clock

d) max_hz == 500000 (500kHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 3  (divide by  8 => CONREG[11- 8] == 3)
               => 60MHz / 128 = 468.75kHz SPI clock

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>

Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.

Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

No need to use the 'status' variable, so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>

When running the "save" command several times on a mx6qsabresd we see:

U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed
U-Boot > save
Saving Environment to MMC...
Writing to MMC(1)... done
U-Boot > save
Saving Environment to MMC...
MMC partition switch failed

This issue is caused by the incorrect usage of CONFIG_SYS_MMC_ENV_PART.

CONFIG_SYS_MMC_ENV_PART should be used to specify the mmc partition that stores
the environment variables.

On some imx boards it is been incorrectly used to pass the partition of kernel
and dtb files for the 'mmcpart' script variable.

Remove the CONFIG_SYS_MMC_ENV_PART usage and configure the 'mmcpart' variable
directly.

Reported-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>

Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.

Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

The boot logo matching is now done in following way:

 - use LOGO_BMP if it is set, or
 - use $(BOARD).bmp if it exists in tools/logos, or
 - use $(VENDOR).bmp if it exists in tools/logos, or
 - use denx.bmp otherwise.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Wolfgang Denk <wd@denx.de>

The number of gpio signal is packed inside CONFIG_SF_DEFAULT_CS macro
(shifted and or'ed with chip select), so it's incorrect to pass
that macro directly as an argument to gpio_direction_output() call.

Also, SPI driver sets the direction and initial value of a gpio,
used as a chip select signal, before any actual activity happens
on the bus.

So, it is safe to just remove the gpio_direction_output call,
that works incorrectly, thus making no effect, anyway.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>

There are 3 IO expanders on the mx6qsabreauto all reset by the
same GPIO, just set it to high to use the IO.

Signed-off-by: Renato Frias <b13784@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.

Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

When the mx6slevk board support was added in U-boot there was no device tree
support for mx6sl, so only a FSL 3.0.35 was tested at that time.

Now that mx6slevk support is available we can boot a device tree kernel, by
adjusting CONFIG_LOADADDR into a proper location, so that a non-dt and a dt
kernels can be booted.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

The vectoring table has to be placed at 0x0, but U-Boot on MX23/MX28
starts from RAM, so the vectoring table at 0x0 is not present. Craft
code that will be placed at 0x0 and will redirect interrupt vectoring
to proper location of the U-Boot in RAM.

Signed-off-by: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

VF610TWR is a board based on Vybrid VF610 SoC.

This patch adds basic support for Vybrid VF610TWR board.

Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

This patch adds Vybrid VF610 to mxc_ocotp document.

Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>