gpmc timeout is disabled and the reset counter
is set to 0. However, if later a driver activates
the timeout setting the reset to a valid value,
the old reset value with zero is still valid
for the first access. In fact, the timeout block
loads the reset counter after a successful access.

Found on a am335x board with a FPGA connected
to the GPMC bus together with the NAND.
When the FPGA driver in kernel activates
the timeout, the system hangs at the first access
by the NAND driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>

AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.

Signed-off-by: Felipe Balbi <balbi@ti.com>

pass correct PHY Address when running on SK
so that we have working ethernet with this board
too.

Signed-off-by: Felipe Balbi <balbi@ti.com>

AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.

Signed-off-by: Felipe Balbi <balbi@ti.com>

Signed-off-by: Felipe Balbi <balbi@ti.com>

when porting u-boot to a new am43xx board, it
helps to know the name of the current unsupported
board so we don't have to hunt for design documents
to figure out what's written in the EEPROM.

Signed-off-by: Felipe Balbi <balbi@ti.com>

Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>

The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Ash Charles <ashcharles@gmail.com>

If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set
for GPMC on chip select #0---size is 0.  In this case, the GPMC
configuration should be reset but not enabled.  Enabling causes the
Gumstix DuoVero board to hang when entering Linux.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
[trini: Switch to testing base as GPMC_SIZE_256M is 0x0]
Signed-off-by: Tom Rini <trini@ti.com>

The symbol "_start" is defined twice in arch/arm/lib/vectors.S:
around line 48 and line 54.

If CONFIG_SYS_DV_NOR_BOOT_CFG is defined (as on calimain board),
build fails:

  arch/arm/lib/vectors.S: Assembler messages:
  arch/arm/lib/vectors.S:54: Error: symbol `_start' is already defined
  make[1]: *** [arch/arm/lib/vectors.o] Error 1
  make: *** [arch/arm/lib] Error 2

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

Currently cntvoff_el2 is initialised with an arbitrary bag of bits
derived from the initial value of cnthctl_el2 on the current CPU. This is
somewhat odd and problematic as some of these bits are UNKNOWN at reset
and may differ across CPUs (which may cause an OS at EL1 to observe time
going backwards across CPUs).

This patch instead initialises cntvoff_el2 with xzr, giving the register
a consistent value of zero on all CPUs.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Tom Rini <trini@ti.com>
Acked-by: David.Feng <fenghua@phytium.com.cn>

Add QSPI support for VF610TWR, such as clock and iomux.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>

Add PAD_CTL_DSE_150ohm and PAD_CTL_PUS_22K_UP for VF610 in
IOMUX_PAD structure.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>

Add Freescale QSPI driver support for VF610.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>

This family is supported by the TPS65218 PMIC.  Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).

Signed-off-by: Tom Rini <trini@ti.com>

Add a driver for the TPS65218 PMIC which is used by TI AM43xx SoCs and
may be used by TI AM335x SoCs.

Signed-off-by: Tom Rini <trini@ti.com>

Similar to OMAP4/5 we need to scale the voltage up prior to changing the
clock frequencies up higher.  Add a similar hook to start with.

Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Tom Rini <trini@ti.com>

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

in almost all cases we need the i2c commands within the u-boot shell.
So we enable them within the common section.

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

if we have no NAND-Chip, we don't need the gpmc-controller and therefore
is no need to init it.

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

For usage of timer6 within B&R we need this defines to enable clock
modules and clk-source.

Also the 'Timer register bits' are expanded.

By the way we add defines for all timers within AM335x SoC.

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

After enabling a module, SW has to wait on IDLEST bit
until it is Fully functional. This wait is missing for UART module
and there is a immediate access of UART registers after this. So there
is a chance of hang on this module( This can happen when we are running
from MPU SRAM). So waiting for IDLEST bit.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

commit a0a37183 "ARM: omap: merge GPMC initialization code for
all platform" needs CONFIG_NOR, CONFIG_NAND or CONFIG_CMD_ONENAND
to be set to access flash. Add CONFIG_NAND for tam3517 derived
boards to prevent the following error: "nand: error: Unable to
find NAND settings in GPMC Configuration - quitting"

cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>

Enable support of nand ecclayout command.

Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>

Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.

Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>

With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>

We have two contexts for booting these platforms.  One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads.  The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL.  In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.

In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus).  In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.

Signed-off-by: Tom Rini <trini@ti.com>

The patch populates the slave data which will be used by flash driver to
set the  flash quad enable bit.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>

The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

updates documentation with explanation on how to select ECC schemes.

Signed-off-by: Pekon Gupta <pekon@ti.com>

This patch add support for BCH16_ECC to omap_gpmc driver.

*need to BCH16 ECC scheme*
With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes
Flash devices have become more suspectible to bit-flips. Thus stronger
ECC schemes are required for protecting the data.
But stronger ECC schemes have come with larger-sized ECC syndromes which require
more space in OOB/Spare. This puts constrains like;
(a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data.
(b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy following equation:
OOBsize per page >= 26 * (page-size / 512)

Signed-off-by: Pekon Gupta <pekon@ti.com>

GPMC can support simultaneous processing of 8 512Byte data chunks, in parallel

Signed-off-by: Pekon Gupta <pekon@ti.com>

OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.

Signed-off-by: Pekon Gupta <pekon@ti.com>