factor out boot cause function to common code to avoid
the duplicate code in each board support package

Signed-off-by: Jason Liu <jason.hui@linaro.org>

Commit 5d2c154 (IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers)
renamed mx31-imx-regs.h to imx-regs.h.

Change the file label accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>

Use the same method of the Linux kernel to print the MX31 silicon version on
boot.

Tested on a MX31PDK with a 2.0 silicon, where it shows:

CPU:   Freescale i.MX31 rev 2.0 at 531 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>

device tree for uboot arm support has already been enabled
in the master branch. This patch enable device tree support
for mx51/53 evk board for DT test.

Signed-off-by: Jason Liu <r64343@freescale.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg

Signed-off-by: Jason Liu <r64343@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch add CONFIG_HW_WATCHDOG to be used
with the internal watchdog timer of the MX31
processor. Two function are exported for the
board maintainers:
	mxc_hw_watchdog_enable
	mxc_hw_watchdog_reset

The board maintainer can decide to use mxc_hw_watchdog_reset as
hw_watchdog_reset, or to implement his own function to reset
the watchdog.
The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS
(value in seconds). The MX31 allows values between 0.5
(CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds.

Signed-off-by: Stefano Babic <sbabic@denx.de>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

config.mk in board directory is obsolete and should be removed.
The patch allows to get rid of own config.mk adding the imximage.cfg
file to the options in the boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Loc Minier <loic.minier@linaro.org>

Two linker scripts for 8xx was missed.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>

I ran into a problem where the reset was failing except when I enabled
debugging support.  After talking with Garret Swalling at Spansion I
was told that the GL-N series of devices require a 500ns wait for the
reset to complete.  The below patch adds a 1us delay after all reset
commands.

-Aaron Williams

Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Stefan Roese <sr@denx.de>

tested on the a4m072 board with a S29GL512P flash.

flinfo without this patch
Bank # 1: CFI conformant flash (16 x 16)  Size: 32 MB in 256 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 16384 ms, write timeout: 2 ms
  Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]

flinfo with this patch
Bank # 1: CFI conformant flash (16 x 16)  Size: 32 MB in 256 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E2301
  Erase timeout: 16384 ms, write timeout: 2 ms
  Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

The M29W800DT parts also report their geometry with the sector layout
reversed.  So add that ID to the flash_fixup_stm function.

Otherwise, we get:
bfin> flinfo

Bank # 1: CFI conformant FLASH (16 x 16)  Size: 1 MB in 19 Sectors
  AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7
  Erase timeout: 8192 ms, write timeout: 1 ms

  Sector Start Addresses:
  20000000        20004000        20006000        20008000        20010000
  20020000        20030000        20040000        20050000        20060000
  20070000        20080000        20090000        200A0000        200B0000
  200C0000        200D0000        200E0000        200F0000

Reported-by: Jianxi Fu <fujianxi@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>

Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be
stopped with well defined keypresses.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This fixes two bugs with comparison of redundant environment flags on
read.

flag0 and flag1 in fw_env_open() were declared signed instead of
unsigned char breaking BOOLEAN mode "== 0xFF" tests and in INCREMENTAL
mode the wrong environment would be chosen where the flag values are
127 and 128 (either way round). With both flags over 128, both signs
flipped and the logic worked by happy accident.

Also there was a logic bug in the INCREMENTAL test (after signedness was
fixed) in the case flag0=0, flag1=255, env 1 would be incorrectly chosen.

Fix both of these.

Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>

This reverts commit 39768f77.

Reson: it breaks a number of boards with embedded environment as the
code size grows in some places.

The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3.  This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>