Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch add CONFIG_HW_WATCHDOG to be used
with the internal watchdog timer of the MX31
processor. Two function are exported for the
board maintainers:
	mxc_hw_watchdog_enable
	mxc_hw_watchdog_reset

The board maintainer can decide to use mxc_hw_watchdog_reset as
hw_watchdog_reset, or to implement his own function to reset
the watchdog.
The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS
(value in seconds). The MX31 allows values between 0.5
(CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds.

Signed-off-by: Stefano Babic <sbabic@denx.de>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

config.mk in board directory is obsolete and should be removed.
The patch allows to get rid of own config.mk adding the imximage.cfg
file to the options in the boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Loc Minier <loic.minier@linaro.org>

Two linker scripts for 8xx was missed.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>

I ran into a problem where the reset was failing except when I enabled
debugging support.  After talking with Garret Swalling at Spansion I
was told that the GL-N series of devices require a 500ns wait for the
reset to complete.  The below patch adds a 1us delay after all reset
commands.

-Aaron Williams

Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Stefan Roese <sr@denx.de>

tested on the a4m072 board with a S29GL512P flash.

flinfo without this patch
Bank # 1: CFI conformant flash (16 x 16)  Size: 32 MB in 256 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 16384 ms, write timeout: 2 ms
  Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]

flinfo with this patch
Bank # 1: CFI conformant flash (16 x 16)  Size: 32 MB in 256 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E2301
  Erase timeout: 16384 ms, write timeout: 2 ms
  Buffer write timeout: 5 ms, buffer size: 32 bytes
[...]

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

The M29W800DT parts also report their geometry with the sector layout
reversed.  So add that ID to the flash_fixup_stm function.

Otherwise, we get:
bfin> flinfo

Bank # 1: CFI conformant FLASH (16 x 16)  Size: 1 MB in 19 Sectors
  AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7
  Erase timeout: 8192 ms, write timeout: 1 ms

  Sector Start Addresses:
  20000000        20004000        20006000        20008000        20010000
  20020000        20030000        20040000        20050000        20060000
  20070000        20080000        20090000        200A0000        200B0000
  200C0000        200D0000        200E0000        200F0000

Reported-by: Jianxi Fu <fujianxi@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>

Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be
stopped with well defined keypresses.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This fixes two bugs with comparison of redundant environment flags on
read.

flag0 and flag1 in fw_env_open() were declared signed instead of
unsigned char breaking BOOLEAN mode "== 0xFF" tests and in INCREMENTAL
mode the wrong environment would be chosen where the flag values are
127 and 128 (either way round). With both flags over 128, both signs
flipped and the logic worked by happy accident.

Also there was a logic bug in the INCREMENTAL test (after signedness was
fixed) in the case flag0=0, flag1=255, env 1 would be incorrectly chosen.

Fix both of these.

Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>

This reverts commit 39768f77.

Reson: it breaks a number of boards with embedded environment as the
code size grows in some places.

The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3.  This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>

The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>

This converts tsec to use the new PHY Lib.  All of the old PHY support
is ripped out.  The old MDIO driver is split off, and placed in
fsl_mdio.c.  The initialization is modified to initialize the MDIO
driver as well.  The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>

The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.

While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible).  Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>

Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6


782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>

8xx was left behind when fixing up powerpc linking
scripts to support -fpic.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>

Mostly putting a space between function name and "(", and
doing return (foo)

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>

There were a few files which were already using phy_read and phy_write
for their PHY function names.  It's only a few places, and the name
seems most appropriate for the high-level abstraction, so let's
rename the other versions to something more specific.

Also, uec_phy.c had a marvell_init function which I renamed to not
conflict with the one in marvell.c

Lastly, uec_phy.c was putting a space between the phy writing
function names, and the open paren, so I fixed that

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>

This is merely a rearrangement.  No changes to the code, except
to remove now-useless declarations.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>