This mirrors the conventions used in other SPI drivers (kirkwood,
davinci, atmel, et al) where the din/dout buffer can be NULL when the
received/transmitted data isn't important.  This reduces the need for
allocating additional buffers when write-only/read-only functionality is
needed.

In the din == NULL case, the received data is simply not stored.  In the
dout == NULL case, zeroes are transmitted.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

Added support for Spansion chip "S25FL512S_512K".

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

When the map_sysmem, then the fatwrite command can support sandbox.
Following command will show how to use it:
  => sb bind 0 sd.img
  => fatls host 0
  => fatwrite host 0 $memaddr filename $filesize

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>

The tools mkimage, dumpimage, fit_info, fit_check_sign
always have the common libraries to be linked,
so HOSTLOADLIBES_* can be consolidated a little bit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

Remove the common infrastructure of nand_spl and
clean-up the code inside ifdef(CONFIG_NAND_U_BOOT)..endif.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Also update README.scrapyard.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Because cmd_mkimage is used in various subdirectories,
it seems reasonable to define it in scripts/Makefile.lib.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

We already have cmd_shipped in scripts/Makefile.lib.
Use it rather than defining a new command cmd_copy.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Emails to the following addresses have been bouncing.

Albin Tonnerre <albin.tonnerre@free-electrons.com>
Anton Shurpin <shurpin.aa@niistt.ru>
Brent Kandetzki <brentk@teleco.com>
Dan Malek <dan@embeddedalley.com>
Frank Panno <fpanno@delphintech.com>
Gary Jennejohn <garyj@denx.de>
Hayden Fraser <Hayden.Fraser@freescale.com>
Eric Millbrandt <emillbrandt@dekaresearch.com>
Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Kumar Gala <kumar.gala@freescale.com>
Joe D'Abbraccio <ljd015@freescale.com>
John Zhan <zhanz@sinovee.com>
Keith Outwater <Keith_Outwater@mvis.com>
Julien May <julien.may@miromico.ch>
Kári Davíðsson <kd@flaga.is>
Kyle Moffett <Kyle.D.Moffett@boeing.com>
Leo Sartre <lsartre@adeneo-embedded.com>
Mike Dunn <mikedunn@newsguy.com>
Dave Ellis <DGE@sixnetio.com>
Chan-Taek Park <c-park@ti.com>
Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>

I am Ccing the current working addresses for some of them.

If you want to get back an Orphan board to Active,
please update your email address.

Please do it only if you still have a real hardware to test on.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albin Tonnerre <albin.tonnerre@gmail.com>
Cc: Anton Shurpin <anton.shurpin@gmail.com>
Cc: Brent Kandetzki <brent.kandetzki@stw-technic.com>
Cc: Dan Malek <dan.malek@konsulko.com>
Cc: Gary Jennejohn <gljennjohn@googlemail.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@gmail.com> ?
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Mike Dunn <mikedunn@newsguy.com>
CC: Jerry Van Baren <vanbaren@cideas.com>

Due to the FIT_MAX_HASH_LEN constant not having been updated
to support SHA256 signatures one will always see a buffer
overflow in fit_image_process_hash when signing images that
use this larger hash.  This is exposed by vboot_test.sh.

Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so move the exportable parts of hash.h outside of
 !USE_HOSTCC and only need that as a new include to image.h]
Signed-off-by: Tom Rini <trini@ti.com>

The offset of module information is at 128, different from DDR3.

Signed-off-by: York Sun <yorksun@freescale.com>

This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM

Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Crossbars and IDT were not getting configured for Serdes2 protocol
0x9d for B4420.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.

This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.

This workaround is valid for B4, T4 and T2 platforms, so
added in their config.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>

When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>

Add a new serdes2 protocol 0x27.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Replace 80 mircoseconds delay with polling flag ESPI_EV_TXE.

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

A-007186: SerDes PLL is calibrated at reset. It is possible
for jitter to increase and cause the PLL to unlock when the
temperature delta from the time the PLL is calibrated exceeds
+56C/-66C when using X VDD of 1.35 V (or +70C/-80C when using
XnVDD of 1.5 V). No issues are seen with LC VCO. The protocols
only using Ring VCOs are impacted.

Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring
VCO, this need to use alternate serdes protocols. Alternate
option has the same functionality as the original option; the
only difference being LC VCO rather than Ring VCO.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

- add support for 2nd DIMM slot.
- make it work with DIMM which is less than 2GB.

Verified with two 2GB UDIMM MT9JSF25672AZ-2G1K1 in two DIMM slots.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.

Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.

- add support for serdes protocols: 0x1b, 0x50, 0x5e,
  0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
  t2080qds and t2080rdb.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Enable legacy image format with CONFIG_IMAGE_FORMAT_LEGACY
on the ids8313 board, as it uses signed FIT images for booting
Linux and need the legacy image format.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Michael Conrad <Michael.Conrad@ids.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

make the use of legacy image format configurable through
the config define CONFIG_IMAGE_FORMAT_LEGACY.

When relying on signed FIT images with required signature check
the legacy image format should be disabled. Therefore introduce
this new define and enable legacy image format if CONFIG_FIT_SIGNATURE
is not set. If CONFIG_FIT_SIGNATURE is set disable per default
the legacy image format.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lars Steubesand <lars.steubesand@philips.com>
Cc: Mike Pearce <mike@kaew.be>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>

The Device Tree Compiler (DTC) used to have its master
repository located on jdl.com.  While it is still there,
its official, new, shiny location is on kernel.org here:

    git://git.kernel.org/pub/scm/utils/dtc/dtc.git



Update a few references to point there instead.

Signed-off-by: Jon Loeliger <jdl@jdl.com>
Acked-by: Simon Glass <sjg@chromium.org>

Add function to find a GPT table entry by name.

Tested on little endian ARMv7 and ARMv8 configurations

Signed-off-by: Steve Rae <srae@broadcom.com>

- update the comments regarding lbaint_t usage
- cleanup casting of values related to the lbaint_t type
- cleanup of a type that requires a u64

Tested on little endian ARMv7 and ARMv8 configurations

Signed-off-by: Steve Rae <srae@broadcom.com>

Tested on little endian ARMv7 and ARMv8 configurations

Signed-off-by: Steve Rae <srae@broadcom.com>

Assign default environment and set env valid during board_init_f
before relocation as the actual environment will be read from eeprom
later.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <monstr@monstr.eu>

Define the MAX_CLUSTSIZE to default of 65536 only if
CONFIG_FS_FAT_MAX_CLUSTSIZE is not defined.
This option has been provided to save memory in some
memory constrained cases.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <monstr@monstr.eu>

The relocation code can now relocate from anywhere to
the RAM.

The old code assumed that the binary was copied to the RAM
by some PBL and then it just relocated the .text section
from the loaded address to the linked address.

Now, it first checks if vectors are somewhere else than the
linked address. If yes, there are copied to address 0 (or
to the exception vector base address if register EVBAR is
present).

Then, the .text section is relocated from its current location
to the RAM.

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>

The OpenRISC architecture specification v1.0 defines
new SPR registers. This patch adds registers definition
for group 0 and update bit definitions for the CPU
configuration register.

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>

get_phy_id returns -EIO when it can't read from a phy at a given addr.  This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.

Example usage:
Replace
    phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
    phydev = phy_find_by_mask(bus, phy_mask, phy_if)
    if (phydev)
	phy_connect_dev(phydev, dev);

Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

It is trivial to crash fit_check_sign by invoking with an
absolute path in a deeply nested directory.  This is exposed
by vboot_test.sh.

Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Acked-by: Simon Glass <sjg@chromium.org>

Both pblimage and mxsimage use the same crc algorithm, so refactor.

Signed-off-by: Charles Manning <cdhmanning@gmail.com>