Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>

PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.

Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Chong Huang <chuang@ucrobotics.com>
Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Info about the hardware can be found here:
	http://www.dilnetpc.com/dnp0086.htm



Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Au1x00 is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

IncaIP is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

All current CPUs and SoCs are based on MIPS32 arch. The complete
code resides in the global arch/mips/cpu directory. This is not
suitable if other MIPS architectures like MIPS64 or Octeon should
be supported in the future.

To achieve this the current CPU code is moved to its own mips32
subdirectory. All MIPS32 boards have to use mips32 as config switch
in board.cfg.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: Tom Warren <twarren@nvidia.com>

Signed-off-by: Tom Warren <twarren@nvidia.com>

Position independant functionality is due for removal from the x86
architecture, so create two distinct configurations - One for Flash and
one for SRAM

We should have been defining the actual board name in the options, not
the processor.  Fix this for P1011RDB, P1020RDB, P2010RDB, and P2020RDB.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Acked-by: Stefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

At the same time, fix up CPU_CLOCK_RATE to have the CONFIG_ prefix to
work with boards.cfg.

Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

CONFIG_QEMU_MIPS is already provided by <configs/qemu-mips.h>, so we
don't generate it using the options fields in boards.cfg.

Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

CONFIG_GTH2 is already provided by <configs/gth2.h>, so we don't
generate it using the options fields in boards.cfg.

Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.

This patch supports the following functions:
 - 256MB DDR3-SDRAM
 - SPI ROM
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for Samsung s5pc210 universal board

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch adds support for CM-T35 board

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic <sbabic@denx.de>

Supported:
MMC
IDE
PMIC
SPI flash
LEDs

I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Add initial support for MX53EVK board support.
FEC, SD/MMC, UART, I2C, have been supported.

Signed-off-by: Jason Liu <r64343@freescale.com>

Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.

Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx



Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.

Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

There is not break character between board name and CPU.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>

The MPC852 based mgsuvd and kmsupx4 boards from keymile
were initially ported but later on not developed further. So
the respective files were removed to avoid unneeded merging
and maintenance.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko <Schocher&lt;hs@denx.de>

Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting
from NAND.

Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The PM854/PM856 boards are no longer maintained and thus we are removing
support for them.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>

The MPC8540EVAL board is no longer maintained and thus we are removing
support for it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The ATUM8548 board is no longer maintained and thus we are removing
support for it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This adds support for the SHMIN SH7706 board(T-SH7706LAN).
The CPU of this board is SH7706.
There are SDRAM of 32M byte, Flash memory of 512K byte, Serial,
10Base Ether and MMC.

http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htm



Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
	* Processor upto 1.2GHz
        * Parallel 1Gb x8 DDR2-1066 MHz
        * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
        * Footprints for eMMC/eSD NAND & MMC x8 card
        * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
        * SEAF memory board, subset of PISMO2
    With Peripherals:
        * 4.3” WVGA 24-bit LCD
        * Audio codecs (AC97 & I2S), TSI
        * VGA camera
        * Video in via 3 RCA jacks, and HDMI type C out
        * Marvell 88W8688 802.11bg/BT module
        * GPS RF IC
        * Dual analog mics & speakers, headset jack, LED, ambient light sensor
        * USB2.0 HS host  (A), OTG (micro AB)
        * FE PHY, PCIE Mini Card  slot
        * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB

Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>