IPv6 FIB should use FIB6_TABLE_HASHSZ, not FIB_TABLE_HASHSZ.

Fixes: ba1cc08d ("ipv6: fix memory leak with multiple tables during netns destruction")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While the cited commit fixed a possible deadlock, it added a leak
of the request socket, since reqsk_put() must be called if the BPF
filter decided the ACK packet must be dropped.

Fixes: d624d276 ("tcp: fix possible deadlock in TCP stack vs BPF filter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fb586f25 ("sctp: delay calls to sk_data_ready() as much as
possible") minimized the number of wake ups that are triggered in case
the association receives a packet with multiple data chunks on it and/or
when io_events are enabled and then commit 0970f5b3 ("sctp: signal
sk_data_ready earlier on data chunks reception") moved the wake up to as
soon as possible. It thus relies on the state machine running later to
clean the flag that the event was already generated.

The issue is that there are 2 call paths that calls
sctp_ulpq_tail_event() outside of the state machine, causing the flag to
linger and possibly omitting a needed wake up in the sequence.

One of the call paths is when enabling SCTP_SENDER_DRY_EVENTS via
setsockopt(SCTP_EVENTS), as noticed by Harald Welte. The other is when
partial reliability triggers removal of chunks from the send queue when
the application calls sendmsg().

This commit fixes it by not setting the flag in case the socket is not
owned by the user, as it won't be cleaned later. This works for
user-initiated calls and also for rx path processing.

Fixes: fb586f25 ("sctp: delay calls to sk_data_ready() as much as possible")
Reported-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

64bit division causes build/link errors on 32bit architectures. It
prints out error messages like:

ERROR: "__aeabi_uldivmod" [net/netfilter/xt_hashlimit.ko] undefined!

The value of avg passed through by userspace in BYTE mode cannot exceed
U32_MAX. Which means 64bit division in user2rate_bytes is unnecessary.
To fix this I have changed the type of param 'user' to u32.

Since anything greater than U32_MAX is an invalid input we error out in
hashlimit_mt_check_common() when this is the case.

Changes in v2:
	Making return type as u32 would cause an overflow for small
	values of 'user' (for example 2, 3 etc). To avoid this I bumped up
	'r' to u64 again as well as the return type. This is OK since the
	variable that stores the result is u64. We still avoid 64bit
	division here since 'user' is u32.

Fixes: bea74641 ("netfilter: xt_hashlimit: add rate match mode")
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

struct xt_byteslimit_htable used hlist_head, but memory allocation is
done through sizeof(struct list_head).

Signed-off-by: Zhizhou Tian <zhizhou.tian@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

kernel test robot reported:

WARNING: CPU: 0 PID: 1244 at net/netfilter/core.c:218 __nf_hook_entries_try_shrink+0x49/0xcd
[..]

After allowing batching in nf_unregister_net_hooks its possible that an earlier
call to __nf_hook_entries_try_shrink already compacted the list.
If this happens we don't need to do anything.

Fixes: d3ad2c17 ("netfilter: core: batch nf_unregister_net_hooks synchronize_net calls")
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

no need to serialize on a single lock, we can partition the table and
add/delete in parallel to different slots.
This restores one of the advantages that got lost with the rhlist
revert.

Cc: Ivan Babrou <ibobrik@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This reverts commit 870190a9.

It was not a good idea. The custom hash table was a much better
fit for this purpose.

A fast lookup is not essential, in fact for most cases there is no lookup
at all because original tuple is not taken and can be used as-is.
What needs to be fast is insertion and deletion.

rhlist removal however requires a rhlist walk.
We can have thousands of entries in such a list if source port/addresses
are reused for multiple flows, if this happens removal requests are so
expensive that deletions of a few thousand flows can take several
seconds(!).

The advantages that we got from rhashtable are:
1) table auto-sizing
2) multiple locks

1) would be nice to have, but it is not essential as we have at
most one lookup per new flow, so even a million flows in the bysource
table are not a problem compared to current deletion cost.
2) is easy to add to custom hash table.

I tried to add hlist_node to rhlist to speed up rhltable_remove but this
isn't doable without changing semantics.  rhltable_remove_fast will
check that the to-be-deleted object is part of the table and that
requires a list walk that we want to avoid.

Furthermore, using hlist_node increases size of struct rhlist_head, which
in turn increases nf_conn size.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=196821


Reported-by: Ivan Babrou <ibobrik@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

There are reports about spurious softlockups during iptables-restore, a
backtrace i saw points at get_counters -- it uses a sequence lock and also
has unbounded restart loop.

Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

It seems preferrable to limp along if we have a conflicting mapping,
its certainly better than a BUG().

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

fib6_net_exit only frees the main and local tables. If another table was
created with fib6_alloc_table, we leak it when the netns is destroyed.

Fix this in the same way ip_fib_net_exit cleans up tables, by walking
through the whole hashtable of fib6_table's. We can get rid of the
special cases for local and main, since they're also part of the
hashtable.

Reproducer:
    ip netns add x
    ip -net x -6 rule add from 6003:1::/64 table 100
    ip netns del x

Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 58f09b78 ("[NETNS][IPV6] ip6_fib - make it per network namespace")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no reason for ipvs to create a conn for an ABORT packet
even if sysctl_sloppy_sctp is set.

This patch is to accept it without creating a conn, just as ipvs
does for tcp's RST packet.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Commit 5e26b1b3 ("ipvs: support scheduling inverse and icmp SCTP
packets") changed to check packet type early. It introduced a side
effect: if it's not a INIT packet, ports will be set as  NULL, and
the packet will be dropped later.

It caused that sctp couldn't create connection when ipvs module is
loaded and any scheduler is registered on server.

Li Shuang reproduced it by running the cmds on sctp server:
  # ipvsadm -A -t 1.1.1.1:80 -s rr
  # ipvsadm -D -t 1.1.1.1:80
then the server could't work any more.

This patch is to return 1 when it's not an INIT packet. It means ipvs
will accept it without creating a conn for it, just like what it does
for tcp.

Fixes: 5e26b1b3 ("ipvs: support scheduling inverse and icmp SCTP packets")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

In rds_send_xmit() there is logic to batch the sends. However, if
another thread has acquired the lock and has incremented the send_gen,
it is considered a race and we yield. The code incrementing the
s_send_lock_queue_raced statistics counter did not count this event
correctly.

This commit counts the race condition correctly.

Changes from v1:
- Removed check for *someone_on_xmit()*
- Fixed incorrect indentation

Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 0ddf3fb2 ("udp: preserve skb->dst if required
for IP options processing") we clear the skb head state as soon
as the skb carrying them is first processed.

Since the same skb can be processed several times when MSG_PEEK
is used, we can end up lacking the required head states, and
eventually oopsing.

Fix this clearing the skb head state only when processing the
last skb reference.

Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 0ddf3fb2 ("udp: preserve skb->dst if required for IP options processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when probessing ICMPV6_PKT_TOOBIG, ip6gre_err only subtracts the
offset of gre header from mtu info. The expected mtu of gre device
should also subtract gre header. Otherwise, the next packets still
can't be sent out.

Jianlin found this issue when using the topo:
  client(ip6gre)<---->(nic1)route(nic2)<----->(ip6gre)server

and reducing nic2's mtu, then both tcp and sctp's performance with
big size data became 0.

This patch is to fix it by also subtracting grehdr (tun->tun_hlen)
from mtu info when updating gre device's mtu in ip6gre_err(). It
also needs to subtract ETH_HLEN if gre dev'type is ARPHRD_ETHER.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a memleak happening for chain 0. The thing is, chain 0 needs to
be always present, not created on demand. Therefore tcf_block_get upon
creation of block calls the tcf_chain_create function directly. The
chain is created with refcnt == 1, which is not correct in this case and
causes the memleak. So move the refcnt increment into tcf_chain_get
function even for the case when chain needs to be created.

Reported-by: Jakub Kicinski <kubakici@wp.pl>
Fixes: 5bc17018 ("net: sched: introduce multichain support for filters")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The net device is already stored in the 'net' variable, so no need to call
dev_net() again.

Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now there is no lock protecting nlk ngroups/groups' accessing in
netlink bind and getname. It's safe from nlk groups' setting in
netlink_release, but not from netlink_realloc_groups called by
netlink_setsockopt.

netlink_lock_table is needed in both netlink bind and getname when
accessing nlk groups.

Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ChunYu found a netlink use-after-free issue by syzkaller:

[28448.842981] BUG: KASAN: use-after-free in __nla_put+0x37/0x40 at addr ffff8807185e2378
[28448.969918] Call Trace:
[...]
[28449.117207]  __nla_put+0x37/0x40
[28449.132027]  nla_put+0xf5/0x130
[28449.146261]  sk_diag_fill.isra.4.constprop.5+0x5a0/0x750 [netlink_diag]
[28449.176608]  __netlink_diag_dump+0x25a/0x700 [netlink_diag]
[28449.202215]  netlink_diag_dump+0x176/0x240 [netlink_diag]
[28449.226834]  netlink_dump+0x488/0xbb0
[28449.298014]  __netlink_dump_start+0x4e8/0x760
[28449.317924]  netlink_diag_handler_dump+0x261/0x340 [netlink_diag]
[28449.413414]  sock_diag_rcv_msg+0x207/0x390
[28449.432409]  netlink_rcv_skb+0x149/0x380
[28449.467647]  sock_diag_rcv+0x2d/0x40
[28449.484362]  netlink_unicast+0x562/0x7b0
[28449.564790]  netlink_sendmsg+0xaa8/0xe60
[28449.661510]  sock_sendmsg+0xcf/0x110
[28449.865631]  __sys_sendmsg+0xf3/0x240
[28450.000964]  SyS_sendmsg+0x32/0x50
[28450.016969]  do_syscall_64+0x25c/0x6c0
[28450.154439]  entry_SYSCALL64_slow_path+0x25/0x25

It was caused by no protection between nlk groups' free in netlink_release
and nlk groups' accessing in sk_diag_dump_groups. The similar issue also
exists in netlink_seq_show().

This patch is to defer nlk groups' free in deferred_put_nlk_sk.

Reported-by: ChunYu Wang <chunwang@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 520ac30f ("net_sched: drop packets after root qdisc lock
is released) made a big change of tc for performance. There are two points
left in sch_prio and sch_qfq which are not changed with that commit. Now
enhance them now with __qdisc_drop.

Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an RX BA session is started by the driver, and it has to tell
mac80211 about it, the corresponding bit in tid_rx_manage_offl gets
set and the BA session work is scheduled. Upon testing this bit, it
will call __ieee80211_start_rx_ba_session(), thus deadlocking as it
already holds the ampdu_mlme.mtx, which that acquires again.

Fix this by adding ___ieee80211_start_rx_ba_session(), a version of
the function that requires the mutex already held.

Cc: stable@vger.kernel.org
Fixes: 699cb58c ("mac80211: manage RX BA session offload without SKB queue")
Reported-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 7a7c0a64 ("mac80211: fix TX aggregation start/stop callback race")
added a cancellation of the ampdu work after the loop that stopped the
Tx and Rx BA sessions. However, in some cases, e.g., during HW reconfig,
the low level driver might call mac80211 APIs to complete the stopping
of the BA sessions, which would queue the ampdu work to handle the actual
completion. This work needs to be performed as otherwise mac80211 data
structures would not be properly synced.

Fix this by checking if BA session STOP_CB bit is set after the BA session
cancellation and properly clean the session.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[Johannes: the work isn't flushed because that could do other things we
 don't want, and the locking situation isn't clear]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Honor the NL80211_RRF_NO_HT40{MINUS,PLUS} flags in
reg_process_ht_flags_channel. Not doing so leads can lead
to a firmware assert in iwlwifi for example.

Fixes: b0d7aa59 ("cfg80211: allow wiphy specific regdomain management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.

Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new TC IDR code uses GFP_KERNEL under spin lock.  Which leads
to:

[  582.621091] BUG: sleeping function called from invalid context at ../mm/slab.h:416
[  582.629721] in_atomic(): 1, irqs_disabled(): 0, pid: 3379, name: tc
[  582.636939] 2 locks held by tc/3379:
[  582.641049]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff910354ce>] rtnetlink_rcv_msg+0x92e/0x1400
[  582.650958]  #1:  (&(&tn->idrinfo->lock)->rlock){+.-.+.}, at: [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[  582.662217] Preemption disabled at:
[  582.662222] [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[  582.672592] CPU: 9 PID: 3379 Comm: tc Tainted: G        W       4.13.0-rc7-debug-00648-g43503a79b9f0 #287
[  582.683432] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.3.4 11/08/2016
[  582.691937] Call Trace:
...
[  582.742460]  kmem_cache_alloc+0x286/0x540
[  582.747055]  radix_tree_node_alloc.constprop.6+0x4a/0x450
[  582.753209]  idr_get_free_cmn+0x627/0xf80
...
[  582.815525]  idr_alloc_cmn+0x1a8/0x270
...
[  582.833804]  tcf_idr_create+0x31b/0x8e0
...

Try to preallocate the memory with idr_prealloc(GFP_KERNEL)
(as suggested by Eric Dumazet), and change the allocation
flags under spin lock.

Fixes: 65a206c0 ("net/sched: Change act_api and act_xxx modules to use IDR")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.

Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful.  This makes sure we always pick up on a write-lock
event.

On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using ifdef in the C file.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In flow dissector there are no limits to the number of nested
encapsulations or headers that might be dissected which makes for a
nice DOS attack. This patch sets a limit of the number of headers
that flow dissector will parse.

Headers includes network layer headers, transport layer headers, shim
headers for encapsulation, IPv6 extension headers, etc. The limit for
maximum number of headers to parse has be set to fifteen to account for
a reasonable number of encapsulations, extension headers, VLAN,
in a packet. Note that this limit does not supercede the STOP_AT_*
flags which may stop processing before the headers limit is reached.

Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.

Reported-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a new link error in allmodconfig kernels after ftgmac100
started using the ncsi helpers:

ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!

Related to that, we get another error when CONFIG_NET_NCSI is disabled:

drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?

This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.

Fixes: 51564585 ("ftgmac100: Support NCSI VLAN filtering when available")
Fixes: 21acf630 ("net/ncsi: Configure VLAN tag filter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are no HT/VHT capabilities in cfg80211_ap_settings::beacon_ies,
these should be looked for in beacon's tail instead.

Fixes: 66cd794e ("nl80211: add HT/VHT capabilities to AP parameters")
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When HW ROC is supported it is possible that after the HW notified
that the ROC has started, the ROC was cancelled and another ROC was
added while the hw_roc_start worker is waiting on the mutex (since
cancelling the ROC and adding another one also holds the same mutex).
As a result, the hw_roc_start worker will continue to run after the
new ROC is added but before it is actually started by the HW.
This may result in notifying userspace that the ROC has started before
it actually does, or in case of management tx ROC, in an attempt to
tx while not on the right channel.

In addition, when the driver will notify mac80211 that the second ROC
has started, mac80211 will warn that this ROC has already been
notified.

Fix this by flushing the hw_roc_start work before cancelling an ROC.

Cc: stable@vger.kernel.org
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since drv_wake_tx_queue() is normally called in the TX path, which
is already in an RCU critical section, we should call it the same
way in the aggregation code path, so if the driver expects to be
able to use RCU, it'll already be protected without having to enter
a nested critical section.

Additionally, disable soft-IRQs, since not doing so could cause
issues in a driver that relies on them already being disabled like
in the other path.

Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This change adds null pointer check before dereferencing pointer dev on
netif_tx_start_all_queues() when an interface is added.
With iTXQ support, netif_tx_start_all_queues() is always called while
an interface is added. however, the netdev queues are not associated
and dev is null when the interface is either NL80211_IFTYPE_P2P_DEVICE
or NL80211_IFTYPE_NAN.

Signed-off-by: Chunho Lee <ch.lee@newracom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

VHT MESH support was added, but the order of the IEs
wasn't enforced. Fix that.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Invoking ht_dbg() with too long of a string will print a warning.
Shorten the messages while retaining the printed patameters.

Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With TXQs, the AP_VLAN interfaces are resolved to their owner AP
interface when enqueuing the frame, which makes sense since the
frame really goes out on that as far as the driver is concerned.

However, this introduces a problem: frames to be encrypted with
a VLAN-specific GTK will now be encrypted with the AP GTK, since
the information about which virtual interface to use to select
the key is taken from the TXQ.

Fix this by preserving info->control.vif and using that in the
dequeue function. This now requires doing the driver-mapping
in the dequeue as well.

Since there's no way to filter the frames that are sitting on a
TXQ, drop all frames, which may affect other interfaces, when an
AP_VLAN is removed.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>