Remove a leftover spinlock.

This was required back when mod_delayed_work() did not exist, and had to
be implemented with a cancel + queue. See commit e7c2f967
("workqueue: use mod_delayed_work() instead of __cancel + queue")

schedule_delayed_work() and mod_delayed_work() can now be used
concurrently. So the spinlock is no longer needed.

Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/input/joystick/db9.c: In function ‘db9_saturn_read_packet’:
drivers/input/joystick/db9.c:256:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (tmp == 0xff) {
      ^
drivers/input/joystick/db9.c:263:2: note: here
  default:
  ^~~~~~~

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Remove a spinlock which prevents schedule_delayed_work() and
mod_delayed_work() from executing concurrently.

This was required back when mod_delayed_work() did not exist,
and had to be implemented with a cancel + schedule. See
commit e7c2f967 ("workqueue: use mod_delayed_work() instead of
__cancel + queue")

schedule_delayed_work() and mod_delayed_work() can now be used
concurrently. So the spinlock is no longer needed.

Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is required to specify generic touchscreen properties via DT.

Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Now that LEDs core allows "blocking" flavor of "set brightness" method we
can use it and get rid of private work item.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.

Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The PTR_ERR(NULL) value is zero and it's not useful to print that.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to access I2C bus when switching brightness, and that may block,
therefore we have to set stmfts_brightness_set() as LED's
brightness_set_blocking() method.

Fixes: 72d1f234 ("Input: tm2-touchkey - add touchkey driver support for TM2")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.

Fixes: 78bcac7b ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
  obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
  work although the touch data contain such information.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add OF match table for the ili210x touchscreen.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the driver to dev-managed allocations.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There is not a single user of the ili210x platform data in the kernel,
just drop it.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add DT binding document for the Ilitek ILI210x and ILI251x
touchscreen controllers.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds a new vibrator driver that supports various Qualcomm
MSM SOCs. Driver was tested on a LG Nexus 5 (hammerhead) phone.

Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On some platforms (e.g.: ARCH_BRCMSTB) it is possible to enter
"poweroff" while leaving some wake-up sources enabled such as key
presses in order to allow for the system to wake-up.

Wire up a .shutdown() callback which calls into the existing
gpio_keys_suspend() since the logic is essentially the same.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should rely on the interrupt trigger (level vs edge) set up by the
firmware or board code instead of forcing what we consider appropriate.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some of the #defined register values are one-bit flags. Convert them to
use the BIT(x) macro instead of 1 byte hexadecimal values. This improves
readability and clarifies the intent.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

of_touchscreen.c provides a common interface for a axis inversion and
swapping of touchscreens. Therefore use it in the sx8654 driver.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: use __be16 in sx8650_irq, add missing del_timer_sync]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

As the sx865[456] share the same datasheet and differ only in the
presence of a "capacitive proximity detection circuit" and a "haptics
motor driver for LRA/ERM" add them to the compatbiles. As the driver
doesn't implement these features it should be no problem.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The sx8654 features a NRST input which may be connected to a GPIO.
Therefore add support for hard-resetting the sx8654 via this NRST.

If the reset-gpio property is provided the sx8654 is resetted via NRST
instead of the soft-reset via I2C.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.

Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf

Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unfortunately the evervision focaltech implementation uses two offset
registers, one for the x coordinate and one for y.

This patch extends the driver to handle those offset registers only for
devices that support these.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently only the threshold and gain parameters can be read.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Evervision displays are using different Focaltech touchscreen
controllers. This commit adds the initial support for the ones using the
FT5726 controller. Receiving the touch data is the same as for the
GENERIC_FT but the x and y cooridnates are swapped. The main differences
are the register addresses where the GAIN and THRESHOLD parameters are
stored.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

iSOrt includes in alphabetical order and remove duplicated include file
linux/kernel.h

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with
memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge with mainline to bring in the new APIs.

regmap_bulk_read() can return a non zero value on failure. The fix checks
if the function call succeeded before calling mod_timer. The issue was
identified by a static analysis tool.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchkey variant found on aries board is slighty different,
it uses a fixed regulator and writes/read to the same place

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>