- Surface Aggregator Module support from Maximilian Luz

- Workaround for broken behavior of Plantronics Blackwire from Maxim
  Mikityanskiy

- Apple Magic Mouse 2 support from John Chen

- Support for newer Quad/BT 2.0 Logitech receivers in HID proxy mode from
  Hans de Goede

- LED fixes and Thinkpad X1 Tablet keyboard support, from Hans de Goede

- Cleanups to ACPI handling in i2c-hid driver from Andy Shevchenko

- Support for FTDI FT260 I2C host adapter from Michael Zaidman

- Mute LED support fixes for Elantech driver from Hans de Goede

- hiddev_connect() return value fix from Jason Gerecke

This is the capacity in percentage, relative to design capacity.
Specifically, it is present in Apple Magic Mouse 2.

In contrast, usage 00850064 is also the capacity in percentage, but is
relative to full capacity. It is not mapped here because I don't have
such device.

Signed-off-by: John Chen <johnchen902@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

It is observed that the Magic Mouse 2 would not enter multi-touch mode
unless the mouse is connected before loading the module. It seems to be
a quirk specific to Magic Mouse 2

Retrying after 500ms fixes the problem for me. The delay can't be
reduced much further --- 300ms didn't work for me. Retrying immediately
after receiving an event didn't work either.

Signed-off-by: John Chen <johnchen902@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

It is observed that, with 3 button emulation, when middle button is
clicked, either the left button or right button is clicked as well. It
is caused by hidinput "correctly" acting on the event, oblivious to the
3 button emulation.

As raw_event has taken care of everything, no further processing is
needed. However, the only way to stop at raw_event is to return an error
(negative) value. Therefore, the processing is stopped at event instead.

[jkosina@suse.cz: fix comment style]
Signed-off-by: John Chen <johnchen902@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Bluetooth device
	Vendor 004c (Apple)
	Device 0269 (Magic Mouse 2)

Add support for Apple Magic Mouse 2, putting the device in multi-touch
mode.

Co-authored-by: Rohit Pidaparthi <rohitpid@gmail.com>
Co-authored-by: RicardoEPRodrigues <ricardo.e.p.rodrigues@gmail.com>
Signed-off-by: John Chen <johnchen902@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The Thinkpad X1 Tablet Thin keyboard's HID interface for the media-keys
and other special functions, is quite similar to the Thinkpad 10 ultrabook
keyboard's mouse/media-keys HID interface.

The only difference is that it needs a bit different key mappings.

Add support for the mute-LED and the non-standard media-keys on this
keyboard by re-using the tp10_ultrabook_kbd code combined with a new
lenovo_input_mapping_x1_tab_kbd() function.

Co-authored-by: Alexander Kobel <a-kobel@a-kobel.de>
Tested-by: Alexander Kobel <a-kobel@a-kobel.de>
Signed-off-by: Alexander Kobel <a-kobel@a-kobel.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Instead of looking for a hdev with a type of HID_TYPE_USBMOUSE find
the interface for the mute/mic-mute/fn-lock LEDs by checking for the
output-report which is used to set them.

This is a preparation patch for adding support for the LEDs on the
X1 tablet thin keyboard which uses the same output-report, but has
a separate (third) USB interface for the touchpad/mouse functionality.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The mute and mic-mute LEDs should be automatically turned on/off based
on the audio-card's mixer settings.

Add the standardized default-trigger names for this, so that the alsa
code can turn the LEDs on/off as appropriate (on supported audio cards).

This brings the mute/mic-mute LED support inline with the thinkpad_acpi
support for the same LEDs in keyboards directly connected to the
laptop's embedded-controller.

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Mapping the mic-mute button to KEY_MICMUTE is technically correct but
KEY_MICMUTE translates to a scancode of 256 (248 + 8) under X,
which does not fit in 8 bits, so it does not work.

Because of this userspace is expecting KEY_F20 instead,
theoretically KEY_MICMUTE should work under Wayland but even
there it does not work, because the desktop-environment is
listening only for KEY_F20 and not for KEY_MICMUTE.

Fixes: bc04b37e ("HID: lenovo: Add ThinkPad 10 Ultrabook Keyboard support")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The LEDs can only by turned on/off, so max_brightness should be set to 1.
Without this the max_brightness sysfs-attribute will report 255 which is
wrong.

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The led_classdev already contains a cached value of the last set
brightness, the brightness_get callback is only meant for LED drivers
which can read back the actual / current brightness from the hardware.

Since lenovo_led_brightness_get() just returns the last set value
it does not add any functionality, so we can just remove it.

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The HID lenovo probe function only attaches drvdata to one of the
USB interfaces, but lenovo_event() will get called for all USB interfaces
to which hid-lenovo is bound.

This allows a malicious device to fake being a device handled by
hid-lenovo, which generates events for which lenovo_event() has
special handling (and thus dereferences hid_get_drvdata()) on another
interface triggering a NULL pointer exception.

Add a check for hid_get_drvdata() returning NULL, avoiding this
possible NULL pointer exception.

Fixes: bc04b37e ("HID: lenovo: Add ThinkPad 10 Ultrabook Keyboard support")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Fix the following issues with lenovo_led_set_tp10ubkbd() error handling:

1. On success hid_hw_raw_request() returns the number of bytes sent.
   So we should check for (ret != 3) rather then for (ret != 0).

2. Actually propagate errors to the caller.

3. Since the LEDs are part of an USB keyboard-dock the mute LEDs can go
   away at any time. Don't log an error when ret == -ENODEV and set the
   LED_HW_PLUGGABLE flag to avoid errors getting logged when the USB gets
   disconnected.

Fixes: bc04b37e ("HID: lenovo: Add ThinkPad 10 Ultrabook Keyboard support")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The lenovo_led_brightness_set function may sleep, so we should have the
the led_class_dev's brightness_set_blocking callback point to it, rather
then the regular brightness_set callback.

When toggled through sysfs this is not a problem, but the brightness_set
callback may be called from atomic context when using LED-triggers.

Fixes: bc04b37e ("HID: lenovo: Add ThinkPad 10 Ultrabook Keyboard support")
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The led_classdev already contains a cached value of the last set
brightness, the brightness_get callback is only meant for LED drivers
which can read back the actual / current brightness from the hardware.

Since elan_mute_led_get_brigtness() just returns the last set value
it does not add any functionality, so we can just remove it.

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The mute LED should be automatically turned on/off based
on the audio-card's mixer settings.

Add the standardized default-trigger name for this, so that the alsa
code can turn the LED on/off as appropriate (on supported audio cards).

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Being integrated into an USB keyboard-dock the mute LED can go away
at any time, leading to the following errors:

[  918.667671] elan 0003:04F3:0755.0002: Failed to set mute led brightness: -19
[  918.667737] leds elan:red:mute: Setting an LED's brightness failed (-19)

Fix this by making the following changes:

1. Don't log an error from elan_mute_led_set_brigtness() when
   ret == -ENODEV
2. Set the LED_HW_PLUGGABLE flag on the mute LED led_classdev

While at it also make sure that elan_mute_led_set_brigtness() returns
an error (-EIO) when ret != 3 but it is not an error (>= 0).

Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add support for the legacy keyboard (KBD/TC=0x08) HID transport layer of
the Surface System Aggregator Module (SSAM) to the Surface HID driver.
On Surface Laptops 1 and 2, this interface is used to connect the
integrated keyboard.

Note that this subsystem interface essentially provides a limited HID
transport layer. In contrast to the generic HID interface (TC=0x15) used
on newer Surface models, this interface only allows (as far as we know)
for a single device to be connected and is otherwise severely limited in
terms of support for feature- and output-reports. Specifically, only
caps-lock-LED output-reports and a single read-only feature-report are
supported.

Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add a HID transport driver to support integrated HID devices on newer
Microsoft Surface models (specifically 7th-generation, i.e. Surface
Laptop 3, Surface Book 3, and later).

On those models, the internal keyboard and touchpad (as well as some
other HID devices with currently unknown function) are connected via the
generic HID subsystem (TC=0x15) of the Surface System Aggregator Module
(SSAM). This subsystem provides a generic HID transport layer, support
for which is implemented by this driver.

Co-developed-by: Blaž Hrastnik <blaz@mxxn.io>
Signed-off-by: Blaž Hrastnik <blaz@mxxn.io>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Merge tag 'platform-drivers-x86-surface-aggregator-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into for-5.13/surface-system-aggregator-intergration

Pull immutable integration branch from Hans de Goede to have a stable base for
SSAM (Surface System Aggregator Module) HID transport subsystem merge.

=====
Signed tag for the immutable platform-surface-aggregator-registry
branch for merging into other sub-systems.

Note this is based on v5.12-rc2.
=====

The "len" variable is uninitialize.

Fixes: 6a82582d ("HID: ft260: add usb hid to i2c host bridge driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.

Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"

Fixes: 6ecfe51b ("Input: refuse to register absolute devices without absinfo")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Tested-by: Juan Garrido <Juan.Garrido@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The FTDI FT260 chip implements USB to I2C/UART bridges through two
USB HID class interfaces. The first - for I2C, and the second for UART.
Each interface is independent, and the kernel detects it as a separate
USB hidraw device.

This commit adds I2C host adapter support.

Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Tested-by: Aaron Jones (FTDI-UK) <aaron.jones@ftdichip.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Some BIOS-es do not initialize the activestatus bits of the AMD_P2C_MSG3
register. This cause the AMD_SFH driver to not register any sensors even
though the laptops in question do have sensors.

Add a DMI quirk-table for specifying sensor-mask overrides based on
DMI match, to make the sensors work OOTB on these laptop models.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199715
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1651886


Fixes: 4f567b9f ("SFH: PCIe driver to add support of AMD sensor fusion hub")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add a sensor_mask module parameter which can be used to override the
sensor-mask read from the activestatus bits of the AMD_P2C_MSG3
registers. Some BIOS-es do not program the activestatus bits, leading
to the AMD-SFH driver not registering any HID devices even though the
laptop in question does actually have sensors.

While at it also fix the wrong indentation of the MAGNO_EN define.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199715
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1651886


Fixes: 4f567b9f ("SFH: PCIe driver to add support of AMD sensor fusion hub")
Suggested-by: Richard Neumann <mail@richard-neumann.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This value is only used once inside amd_mp2_get_sensor_num(),
so there is no need to store this in the amd_mp2_dev struct,
amd_mp2_get_sensor_num() can simple use a local variable for this.

Fixes: 4f567b9f ("SFH: PCIe driver to add support of AMD sensor fusion hub")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Fix the following coccicheck warnings:

./drivers/hid/wacom_wac.c:2536:2-6: WARNING: Assignment of
0/1 to bool variable.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

In lk 5.11.0-rc2 connecting a USB based Silicon Labs HID to I2C
bridge evaluation board (CP2112EK) causes this warning:
  gpio gpiochip0: (cp2112_gpio): detected irqchip that is shared
       with multiple gpiochips: please fix the driver

Simply copy what other gpio related drivers do to fix this
particular warning: replicate the struct irq_chip object in each
device instance rather than have a static object which makes that
object (incorrectly) shared by each device.

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

When input_register_device() fails, no error return code is assigned.
To fix this bug, ret is assigned with -ENOENT as error return code.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Some new 2021 version of ASUS gamer laptops are using an updated
N-Key keyboard with the PID of 0x19b6. This version is using the
same init sequence and brightness control as the 0x1866 keyboard.

Signed-off-by: Luke D Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The only caller of this function only cares about gross success/failure
but we still might as well resolve the following smatch warning and fix
the other error paths as well:

    hiddev.c:894 hiddev_connect() warn: returning -1 instead of -ENOMEM is sloppy

Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.

The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.

Fixes: 81bb773f ("HID: plantronics: Update to map volume up/down controls")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>