Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.

Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If there are simulatenous queries of regdb, then there might be a case
where multiple queries can trigger request_firmware_no_wait and can have
parallel callbacks being executed asynchronously. In this scenario we
might hit the WARN_ON.

So remove the warn_on, as the code already handles multiple callbacks
gracefully.

Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During refactor in commit 9e478066 ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:

  struct {
          struct ieee80211_hdr_3addr hdr;
          u8 category;
          u8 action_code;
  } __packed action;

But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:

  struct ieee80211_hdr {
  	__le16 frame_control;
  	__le16 duration_id;
  	u8 addr1[ETH_ALEN];
  	u8 addr2[ETH_ALEN];
  	u8 addr3[ETH_ALEN];
  	__le16 seq_ctrl;
  	u8 addr4[ETH_ALEN];
  } __packed __aligned(2);

Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.

This removes the following warning (W=1):

  net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]

Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Following call trace is observed while adding TDLS peer entry in driver
during TDLS setup.

Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0

Fixing this by allowing TDLS setup request only when we have completed
association.

Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.

Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.

Reported-by:  <syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com>
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f2 ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set
flow sport from 'saddr'. However, transport->saddr is set only when
transport->dst exists in sctp_transport_route().

If sctp_transport_pmtu() is called without transport->saddr set, like
when transport->dst doesn't exists, the flow sport will be set to 0
from transport->saddr, which will cause a wrong route to be got.

Commit 6e91b578 ("sctp: re-use sctp_transport_pmtu in
sctp_transport_route") made the issue be triggered more easily
since sctp_transport_pmtu() would be called in sctp_transport_route()
after that.

In gerneral, fl4->fl4_sport should always be set to
htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist
in sctp_v4/6_get_dst(), which is the case:

  sctp_ootb_pkt_new() ->
    sctp_transport_route()

For that, we can simply handle it by setting flow sport from saddr only
when it's 0 in sctp_v4/6_get_dst().

Fixes: 6e91b578 ("sctp: re-use sctp_transport_pmtu in sctp_transport_route")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the paths:

  sctp_sf_do_unexpected_init() ->
    sctp_make_init_ack()
  sctp_sf_do_dupcook_a/b()() ->
    sctp_sf_do_5_1D_ce()

The new chunk 'retval' transport is set from the incoming chunk 'chunk'
transport. However, 'retval' transport belong to the new asoc, which
is a different one from 'chunk' transport's asoc.

It will cause that the 'retval' chunk gets set with a wrong transport.
Later when sending it and because of Commit b9fd6839 ("sctp: add
sctp_packet_singleton"), sctp_packet_singleton() will set some fields,
like vtag to 'retval' chunk from that wrong transport's asoc.

This patch is to fix it by setting 'retval' transport correctly which
belongs to the right asoc in sctp_make_init_ack() and
sctp_sf_do_5_1D_ce().

Fixes: b9fd6839 ("sctp: add sctp_packet_singleton")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to improve sctp stream adding events in 2 places:

  1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM
     and in stream allocation failure checks, as the adding has to
     succeed after reconf_timer stops for the in stream adding
     request retransmission.

  3. In sctp_process_strreset_addstrm_in(), no event should be sent,
     as no in or out stream is added here.

Fixes: 50a41591 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter")
Fixes: c5c4ebb3 ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to improve sctp stream reset events in 4 places:

  1. In sctp_process_strreset_outreq(), the flag should always be set with
     SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in
     stream is reset here.
  2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN
     check, as the reset has to succeed after reconf_timer stops for the
     in stream reset request retransmission.
  3. In sctp_process_strreset_inreq(), no event should be sent, as no in
     or out stream is reset here.
  4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or
     OUTGOING event should always be sent for stream reset requests, no
     matter it fails or succeeds to process the request.

Fixes: 81054476 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter")
Fixes: 16e1a919 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter")
Fixes: 11ae76e6 ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24

Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst

With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun

Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot found that ax25 routes where not properly protected
against concurrent use [1].

In this particular report the bug happened while
copying ax25->digipeat.

Fix this problem by making sure we call ax25_get_route()
while ax25_route_lock is held, so that no modification
could happen while using the route.

The current two ax25_get_route() callers do not sleep,
so this change should be fine.

Once we do that, ax25_get_route() no longer needs to
grab a reference on the found route.

[1]
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
BUG: KASAN: use-after-free in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: use-after-free in kmemdup+0x42/0x60 mm/util.c:113
Read of size 66 at addr ffff888066641a80 by task syz-executor2/531

ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
CPU: 1 PID: 531 Comm: syz-executor2 Not tainted 5.0.0-rc2+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1db/0x2d0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 check_memory_region_inline mm/kasan/generic.c:185 [inline]
 check_memory_region+0x123/0x190 mm/kasan/generic.c:191
 memcpy+0x24/0x50 mm/kasan/common.c:130
 memcpy include/linux/string.h:352 [inline]
 kmemdup+0x42/0x60 mm/util.c:113
 kmemdup include/linux/string.h:425 [inline]
 ax25_rt_autobind+0x25d/0x750 net/ax25/ax25_route.c:424
 ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1224
 __sys_connect+0x357/0x490 net/socket.c:1664
 __do_sys_connect net/socket.c:1675 [inline]
 __se_sys_connect net/socket.c:1672 [inline]
 __x64_sys_connect+0x73/0xb0 net/socket.c:1672
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458099
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f870ee22c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458099
RDX: 0000000000000048 RSI: 0000000020000080 RDI: 0000000000000005
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f870ee236d4
R13: 00000000004be48e R14: 00000000004ce9a8 R15: 00000000ffffffff

Allocated by task 526:
 save_stack+0x45/0xd0 mm/kasan/common.c:73
 set_track mm/kasan/common.c:85 [inline]
 __kasan_kmalloc mm/kasan/common.c:496 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:469
 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:504
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
 kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3609
 kmalloc include/linux/slab.h:545 [inline]
 ax25_rt_add net/ax25/ax25_route.c:95 [inline]
 ax25_rt_ioctl+0x3b9/0x1270 net/ax25/ax25_route.c:233
 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
 sock_do_ioctl+0xe2/0x400 net/socket.c:950
 sock_ioctl+0x32f/0x6c0 net/socket.c:1074
 vfs_ioctl fs/ioctl.c:46 [inline]
 file_ioctl fs/ioctl.c:509 [inline]
 do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
 __do_sys_ioctl fs/ioctl.c:720 [inline]
 __se_sys_ioctl fs/ioctl.c:718 [inline]
 __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
Freed by task 550:
 save_stack+0x45/0xd0 mm/kasan/common.c:73
 set_track mm/kasan/common.c:85 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:458
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:466
 __cache_free mm/slab.c:3487 [inline]
 kfree+0xcf/0x230 mm/slab.c:3806
 ax25_rt_add net/ax25/ax25_route.c:92 [inline]
 ax25_rt_ioctl+0x304/0x1270 net/ax25/ax25_route.c:233
 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
 sock_do_ioctl+0xe2/0x400 net/socket.c:950
 sock_ioctl+0x32f/0x6c0 net/socket.c:1074
 vfs_ioctl fs/ioctl.c:46 [inline]
 file_ioctl fs/ioctl.c:509 [inline]
 do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
 __do_sys_ioctl fs/ioctl.c:720 [inline]
 __se_sys_ioctl fs/ioctl.c:718 [inline]
 __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff888066641a80
 which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes inside of
 96-byte region [ffff888066641a80, ffff888066641ae0)
The buggy address belongs to the page:
page:ffffea0001999040 count:1 mapcount:0 mapping:ffff88812c3f04c0 index:0x0
flags: 0x1fffc0000000200(slab)
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
raw: 01fffc0000000200 ffffea0001817948 ffffea0002341dc8 ffff88812c3f04c0
raw: 0000000000000000 ffff888066641000 0000000100000020 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff888066641980: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
 ffff888066641a00: 00 00 00 00 00 00 00 00 02 fc fc fc fc fc fc fc
>ffff888066641a80: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
                   ^
 ffff888066641b00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
 ffff888066641b80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This message gets logged far too often for how interesting is it.

Most distributions nowadays configure NetworkManager to use randomly
generated MAC addresses for Wi-Fi network scans. The interfaces end up
being periodically brought down for the address change. When they're
subsequently brought back up, the message is logged, eventually flooding
the log.

Perhaps the message is not all that helpful: it seems to be more
interesting to hear when the addrconf actually start, not when it does
not. Let's lower its level.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-By: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in6_dump_addrs() returns a positive 1 if there was nothing to dump.
This return value can not be passed as return from inet6_dump_addr()
as is, because it will confuse rtnetlink, resulting in NLMSG_DONE
never getting set:

$ ip addr list dev lo
EOF on netlink
Dump terminated

v2: flip condition to avoid a new goto (DaveA)

Fixes: 7c1e8a38 ("netlink: fixup regression in RTM_GETADDR")
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ERSPAN key header field as tunnel key in gre_parse_header routine
since ERSPAN protocol sets the key field of the external GRE header to
0 resulting in a tunnel lookup fail in ip6gre_err.
In addition remove key field parsing and pskb_may_pull check in
erspan_rcv and ip6erspan_rcv

Fixes: 5a963eb6 ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).

Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2



Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.

Reported-by: Kyungtae Kim <kt0755@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26
Tested-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

con_fault() can transition the connection into STANDBY right after
ceph_con_keepalive() clears STANDBY in clear_standby():

    libceph user thread               ceph-msgr worker

ceph_con_keepalive()
  mutex_lock(&con->mutex)
  clear_standby(con)
  mutex_unlock(&con->mutex)
                                mutex_lock(&con->mutex)
                                con_fault()
                                  ...
                                  if KEEPALIVE_PENDING isn't set
                                    set state to STANDBY
                                  ...
                                mutex_unlock(&con->mutex)
  set KEEPALIVE_PENDING
  set WRITE_PENDING

This triggers warnings in clear_standby() when either ceph_con_send()
or ceph_con_keepalive() get to clearing STANDBY next time.

I don't see a reason to condition queue_con() call on the previous
value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING
into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING
could have been a non-atomic flag.

Reported-by:  <syzbot+acdeb633f6211ccdf886@syzkaller.appspotmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Myungho Jung <mhjungk@gmail.com>

Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:

    BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
    BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942

    kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
    check_memory_region_inline mm/kasan/kasan.c:260 [inline]
    check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
    memcpy+0x23/0x50 mm/kasan/kasan.c:302
    memcpy include/linux/string.h:345 [inline]
    skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    __pskb_copy include/linux/skbuff.h:1053 [inline]
    pskb_copy include/linux/skbuff.h:2904 [inline]
    skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
    ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
    sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
    __netdev_start_xmit include/linux/netdevice.h:4325 [inline]
    netdev_start_xmit include/linux/netdevice.h:4334 [inline]
    xmit_one net/core/dev.c:3219 [inline]
    dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
    __dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
    dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
    __bpf_tx_skb net/core/filter.c:2016 [inline]
    __bpf_redirect_common net/core/filter.c:2054 [inline]
    __bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
    ____bpf_clone_redirect net/core/filter.c:2094 [inline]
    bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
    bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000

The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.

Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.

Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.

The test itself can be run only from commit 1cf1cae9 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.

Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.

Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero.  For unicast frames
destined for other hosts, we stop processing the frame at that point.

For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA.  That
doesn't match the usual definition of "dropped," so don't count
those as such.

With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.

Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.

In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.

The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.

Fixes: 816a3bed ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.

Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).

To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1

So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.

Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cb9f1b78, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:

Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
    TX: bytes  packets  errors  dropped carrier collsns
    0          0        1       0       0       0

The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).

This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/


Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If sch_fq packet scheduler is not used, TCP can fallback to
internal pacing, but this requires sk_pacing_status to
be properly set.

Fixes: 8c4b4c7e ("bpf: Add setsockopt helper function to bpf")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

In sock_setsockopt() (net/core/sock.h), when SO_MARK option is used
to change sk_mark, sk_dst_reset(sk) is called. The same should be
done in bpf_setsockopt().

Fixes: 8c4b4c7e ("bpf: Add setsockopt helper function to bpf")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

After commit 23b0269e ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.

And this issue was found with LTP/network tests as well.

Fixes: 23b0269e ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 4cdeeee9 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.

The issue was found with LTP/network tests (UDP-Lite test-cases).

Fixes: 4cdeeee9 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes (especially 05cd271f ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.

v2:
- use kzalloc() instead of kcalloc()

Fixes: 05cd271f ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warnings (W=1).

To preserve as much of the existing comment only change a ‘:’ into a ‘,’.
This is enough change, to match the regular expression expected by GCC.

This commit removes the following warning:

  net/core/filter.c:5310:6: warning: this statement may fall through [-Wimplicit-fallthrough=]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.

Fixes: bec1f6f6 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not
an explicit section. so linking warning occurred at compile time for the
powerpc.
So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh".

Config condition:

CONFIG_BPFILTER=y
CONFIG_BPFILTER_UMH=y

Result:

ld: warning: orphan section `.bpfilter_umh' from
`net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh'

Fixes: 61fbf593 ("net: bpfilter: restart bpfilter_umh when error occurred")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"IPv6: " prefix is already added by pr_fmt, no need to include
it again in the pr_warn() format.  The message predates extack
support, we can replace the whole thing with an extack message.

Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This should be 1 for normal allocations, 0 disables leak reporting.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Fixes: 85704cb8 ("net/core/neighbour: tell kmemleak about hash tables")
Signed-off-by: David S. Miller <davem@davemloft.net>

The similar issue as fixed in Commit 4a2eb0c3 ("sctp: initialize
sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists
in sctp_inetaddr_event, as Alexander noticed.

To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp
ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist().

Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reported-by:  <syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As said in draft-foschiano-erspan-03#section4:

   Different frame variants known as "ERSPAN Types" can be
   distinguished based on the GRE "Protocol Type" field value: Type I
   and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].

So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().

Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number.  This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.

This bug is _not_ introduced by commit 3b3ae880
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b968 ("sched: introduce vlan action") which
introduced this bug.

Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both gue_err() and gue6_err() incorrectly assume
linear skbs. Fix them to use pskb_may_pull().

BUG: KMSAN: uninit-value in gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
CPU: 0 PID: 18083 Comm: syz-executor1 Not tainted 5.0.0-rc1+ #7
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x173/0x1d0 lib/dump_stack.c:113
 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600
 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
 gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
 __udp6_lib_err_encap_no_sk net/ipv6/udp.c:434 [inline]
 __udp6_lib_err_encap net/ipv6/udp.c:491 [inline]
 __udp6_lib_err+0x18d0/0x2590 net/ipv6/udp.c:522
 udplitev6_err+0x118/0x130 net/ipv6/udplite.c:27
 icmpv6_notify+0x462/0x9f0 net/ipv6/icmp.c:784
 icmpv6_rcv+0x18ac/0x3fa0 net/ipv6/icmp.c:872
 ip6_protocol_deliver_rcu+0xb5a/0x23a0 net/ipv6/ip6_input.c:394
 ip6_input_finish net/ipv6/ip6_input.c:434 [inline]
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ip6_input+0x2b6/0x350 net/ipv6/ip6_input.c:443
 dst_input include/net/dst.h:450 [inline]
 ip6_rcv_finish+0x4e7/0x6d0 net/ipv6/ip6_input.c:76
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ipv6_rcv+0x34b/0x3f0 net/ipv6/ip6_input.c:272
 __netif_receive_skb_one_core net/core/dev.c:4973 [inline]
 __netif_receive_skb net/core/dev.c:5083 [inline]
 process_backlog+0x756/0x10e0 net/core/dev.c:5923
 napi_poll net/core/dev.c:6346 [inline]
 net_rx_action+0x78b/0x1a60 net/core/dev.c:6412
 __do_softirq+0x53f/0x93a kernel/softirq.c:293
 do_softirq_own_stack+0x49/0x80 arch/x86/entry/entry_64.S:1039
 </IRQ>
 do_softirq kernel/softirq.c:338 [inline]
 __local_bh_enable_ip+0x16f/0x1a0 kernel/softirq.c:190
 local_bh_enable+0x36/0x40 include/linux/bottom_half.h:32
 rcu_read_unlock_bh include/linux/rcupdate.h:696 [inline]
 ip6_finish_output2+0x1d64/0x25f0 net/ipv6/ip6_output.c:121
 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
 NF_HOOK_COND include/linux/netfilter.h:278 [inline]
 ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
 dst_output include/net/dst.h:444 [inline]
 ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211
 __do_sys_sendmmsg net/socket.c:2240 [inline]
 __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x457ec9
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f4a5204fc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000457ec9
RDX: 00000000040001ab RSI: 0000000020000240 RDI: 0000000000000003
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4a520506d4
R13: 00000000004c4ce5 R14: 00000000004d85d8 R15: 00000000ffffffff

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline]
 kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159
 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
 slab_post_alloc_hook mm/slab.h:446 [inline]
 slab_alloc_node mm/slub.c:2754 [inline]
 __kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4377
 __kmalloc_reserve net/core/skbuff.c:140 [inline]
 __alloc_skb+0x309/0xa20 net/core/skbuff.c:208
 alloc_skb include/linux/skbuff.h:1012 [inline]
 alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5288
 sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091
 sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108
 __ip6_append_data+0x42ed/0x5dc0 net/ipv6/ip6_output.c:1443
 ip6_append_data+0x3c2/0x650 net/ipv6/ip6_output.c:1619
 icmp6_send+0x2f5c/0x3c40 net/ipv6/icmp.c:574
 icmpv6_send+0xe5/0x110 net/ipv6/ip6_icmp.c:43
 ip6_link_failure+0x5c/0x2c0 net/ipv6/route.c:2231
 dst_link_failure include/net/dst.h:427 [inline]
 vti_xmit net/ipv4/ip_vti.c:229 [inline]
 vti_tunnel_xmit+0xf3b/0x1ea0 net/ipv4/ip_vti.c:265
 __netdev_start_xmit include/linux/netdevice.h:4382 [inline]
 netdev_start_xmit include/linux/netdevice.h:4391 [inline]
 xmit_one net/core/dev.c:3278 [inline]
 dev_hard_start_xmit+0x604/0xc40 net/core/dev.c:3294
 __dev_queue_xmit+0x2e48/0x3b80 net/core/dev.c:3864
 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3897
 neigh_direct_output+0x42/0x50 net/core/neighbour.c:1511
 neigh_output include/net/neighbour.h:508 [inline]
 ip6_finish_output2+0x1d4e/0x25f0 net/ipv6/ip6_output.c:120
 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
 NF_HOOK_COND include/linux/netfilter.h:278 [inline]
 ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
 dst_output include/net/dst.h:444 [inline]
 ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211
 __do_sys_sendmmsg net/socket.c:2240 [inline]
 __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Fixes: b8a51b38 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of
the connection and so transitions this socket to CLOSE_WAIT state.

Transmission in close wait state is acceptable. Other similar tests in
the stack (e.g., in FastOpen) accept both states. Relax this test, too.

Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html


Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Yuchung Cheng <ycheng@google.com>
CC: Neal Cardwell <ncardwell@google.com>
CC: Soheil Hassas Yeganeh <soheil@google.com>
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

running the following TDC test cases:

 7afc - Replace tunnel_key set action with all parameters
 364d - Replace tunnel_key set action with all parameters and cookie

it's possible to trigger kmemleak warnings like:

  unreferenced object 0xffff94797127ab40 (size 192):
  comm "tc", pid 3248, jiffies 4300565293 (age 1006.862s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 c0 93 f9 8a ff ff ff ff  ................
    41 84 ee 89 ff ff ff ff 00 00 00 00 00 00 00 00  A...............
  backtrace:
    [<000000001e85b61c>] tunnel_key_init+0x31d/0x820 [act_tunnel_key]
    [<000000007f3f6ee7>] tcf_action_init_1+0x384/0x4c0
    [<00000000e89e3ded>] tcf_action_init+0x12b/0x1a0
    [<00000000c1c8c0f8>] tcf_action_add+0x73/0x170
    [<0000000095a9fc28>] tc_ctl_action+0x122/0x160
    [<000000004bebeac5>] rtnetlink_rcv_msg+0x263/0x2d0
    [<000000009fd862dd>] netlink_rcv_skb+0x4a/0x110
    [<00000000b55199e7>] netlink_unicast+0x1a0/0x250
    [<000000004996cd21>] netlink_sendmsg+0x2c1/0x3c0
    [<000000004d6a94b4>] sock_sendmsg+0x36/0x40
    [<000000005d9f0208>] ___sys_sendmsg+0x280/0x2f0
    [<00000000dec19023>] __sys_sendmsg+0x5e/0xa0
    [<000000004b82ac81>] do_syscall_64+0x5b/0x180
    [<00000000a0f1209a>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<000000002926b2ab>] 0xffffffffffffffff

when the tunnel_key action is replaced, the kernel forgets to release the
dst metadata: ensure they are released by tunnel_key_init(), the same way
it's done in tunnel_key_release().

Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>