mx6q: mx6qsabrelite: Add ECSPI support to the Sabrelite platform

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>

board/freescale/mx6qsabrelite/imximage.cfg

@@ -156,7 +156,7 @@ DATA 4 0x021b0404 0x00011006
 
 # set the default clock gate to save power
 DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC00
+DATA 4 0x020c406c 0x0030FC03
 DATA 4 0x020c4070 0x0FFFC000
 DATA 4 0x020c4074 0x3FF00000
 DATA 4 0x020c4078 0x00FFF300

board/freescale/mx6qsabrelite/mx6qsabrelite.c

@@ -46,6 +46,10 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |		\
 	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
 
+#define SPI_PAD_CTRL (PAD_CTL_HYS |				\
+	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm     | PAD_CTL_SRE_FAST)
+
 int dram_init(void)
 {
        gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
@@ -193,6 +197,23 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+#ifdef CONFIG_MXC_SPI
+iomux_v3_cfg_t ecspi1_pads[] = {
+	/* SS1 */
+	MX6Q_PAD_EIM_D19__GPIO_3_19   | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6Q_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6Q_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6Q_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+void setup_spi(void)
+{
+	gpio_direction_output(GPIO_NUMBER(3, 19), 1);
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+					 ARRAY_SIZE(ecspi1_pads));
+}
+#endif
+
 #define MII_1000BASET_CTRL		0x9
 #define MII_EXTENDED_CTRL		0xb
 #define MII_EXTENDED_DATAW		0xc
@@ -239,6 +260,10 @@ int board_eth_init(bd_t *bis)
 		return ret;
 	}
 
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+
 	return 0;
 }
 

include/configs/mx6qsabrelite.h

@@ -44,6 +44,15 @@
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE           UART2_BASE
 
+#define CONFIG_CMD_SF
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_SPEED 25000000
+#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
+#endif
+
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC