Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>

Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU

Introduce two new macros to control conditional setup
     MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x)
     MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x)

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>

The interface to the mxc_gpio driver uses integer (ordinal) values to
refer to all GPIOs on the i.MX processors. The registers themselves
and much of the i.MX documentation are banked in groups of 32, and these
macros allow the use of the port:index numbering for clarity.

GPIO_NUMBER() converts to ordinal value from port:index
GPIO_PORT() returns the port of an ordinal value
GPIO_INDEX() returns the index or offset of the ordinal.

Discussion on the mailing list at
	http://lists.denx.de/pipermail/u-boot/2012-January/116927.html



Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>

This patch fixes booting i.MX28 CPUs via USB download.
In this mode the CPU's bootrom implements a USB HID device that
accepts a bootstream.

When downloading the bootstream via USB, first the SPL code is
received and executed. Then the u-boot image is received and
called.

The USB bootmode is interrupt driven.

This patch fixes two things:

1) The ARM's fast interrupt mode is disabled when the SPL code
has been run. So save and restore the CPSR register.

2) Save and restore c1 control register: the exception vector
location needs to be set back to bootrom space to make the USB
interrupts work again. The SPL code needs to change this
option for the ram size probing.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

The DC power STS shouldn't be checked if booting off 5V supply.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>

commit f31a911f (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Helmut Raiger <helmut.raiger@hale.at>

commit f31a911f (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.

Signed-off-by: Stefano Babic <sbabic@denx.de>

This patch adds SPI support for the MX28EVK. Support for
an optionally installed SPI flash is also added. An example
configuration for redundant envrionment from SPI flash is also
added but disabled by default.

This patch has been tested on a MX28EVK Rev. D with an installed
SST25VF032B 32Mbit SPI flash.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch enables USB host support on the MX28EVK board.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

* 'master' of git://git.denx.de/u-boot-microblaze:
  microblaze: Enable TFTP put command
  microblaze: avoid interrupt race conditions
  microblaze: fix build failure due to undefined reference to `get_ticks'

Signed-off-by: Stephan Linz <linz@li-pro.net>

The interrupt acknowledge action have to run after the
registered interrupt handler. So we have a chance to
bear out the corresponding interrupt request in the
corresponding controller hardware.

With this reordering, we optain a proper interrupt
handling for level triggered interrupt sources -- for
example the new axi_timer v1.02.a introduced in ISE 13.2.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Michal Simek <monstr@monstr.eu>

after commit "common: add possibility for readline_into_buffer
timeout" (sha1:9c348311) was applied. The Microblaze generic build
fails with error below:

common/libcommon.o: In function `cread_line':
/devel/u-boot/common/main.c:717: undefined reference to `get_ticks'
/devel/u-boot/common/main.c:717: undefined reference to `get_tbclk'
/devel/u-boot/common/main.c:720: undefined reference to `get_ticks'

Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Michal Simek <monstr@monstr.eu>

This reverts commits 2faa7619 as
this has introduced some large problems on all other platforms and have
more changes in them than the commit message implies.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

This reverts commit 498cbdfe as we need
to revert the i2c changes that add the support for the platform.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

* 'master' of git://git.denx.de/u-boot-mmc:
  mmc: make mmc_send_status() more reliable
  mmc: fix card busy polling
  Tegra: mmc: Fixed handling of interrupts in timeouts.
  omap_hsmmc: Wait for CMDI to be clear

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/8xxx:Add MPH controller support in USB device-tree fixup
  powerpc/8xxx: Cleanup USB device-tree fixup

* 'trini@ti.com' of git://git.denx.de/u-boot-staging:
  usb_ether: fix typo
  cmd_eeprom: typo
  doc: complete, typos

* 'master' of git://git.denx.de/u-boot-x86:
  x86: Convert board_init_f_r to a processing loop
  x86: Split init functions out of board.c
  x86: Move relocation code out of board.c
  x86: Move setup_pcat_compatibility() out of board.c
  x86: Move do_go_exec() out of board.c
  CHECKPATCH: arch/x86/lib/*
  x86: Tweak IDT and GDT for alignment and readability
  x86: Allow cache before copy to RAM
  x86: Create weak init_cache() and default enable_caches() functions
  x86: Set GD_FLG_RELOC after entering in-RAM copy of U-Boot
  x86: Use fs for global data
  x86: Rework relocation calculations
  x86: Simplify Flash-to-RAM code execution transition
  x86: Rework Global Descriptor Table loading
  x86: Remove GDR related magic numbers
  x86: Speed up copy-to-RAM and clear BSS operations
  x86: Import glibc memcpy implementation

Align the card status polling with the Linux kernel and retry the
command at least five times. Also some cards apparently mishandle the
status bits, so make sure to check the card state too.

Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>

A MMC/SD card may always go into the programming state (and hence be
busy) after a block write. Therefore always check the card state, even
after single block writes. On the other hand there is no need to check
the card status after a read.

Also make sure that errors during busy polling are propagated upwards.

Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>

We are seeing occasional timeouts in the Tegra mmc code when
we are reading from external MMC cards. These don't seem to be
detrimental if they are handled properly.  This CL properly
clears the "normal interrupt status register" (norintsts) in
error conditions.  If we don't do this, when we come back into
mmc_send_cmd() the register will still contain status from the
last transaction.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case.  This makes the code check
for both bits being clear and makes the error print more clear as
to what happened.  DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.

Fix originally spotted by Peter Bigot.

Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>

Add support for fixing usb mode and phy type for
MPH(Multi Port Host) USB controllers in device-tree nodes.
Required for socs like P3060, P5020, etc having MPH USB controller

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

Some code cleanup done for USB device-tree fixup:
	- handling error value returned from fdt_fixup_usb_mode_phy_type()
	- using ARRAY_SIZE macro
	- using snprintf instead of sprintf

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

mention repeatable to README.commands and fix some typos

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>

* 'sf' of git://git.denx.de/u-boot-blackfin:
  README: Add description of SPI Flash (SF) command configuration
  sf command: allow default bus and chip selects
  sf: eeprom_m95xxx: set a sane default timeout
  sf: eeprom_m95xxx: fix up style

* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: pata_bfin: fix printf warning
  Blackfin: bfin_nand: mark local func static
  linkage.h: move from blackfin to common includes
  Blackfin: br4: new board port
  Blackfin: add in/out le32 variants
  post: add blackfin to the post_time_ms list
  Blackfin: bf537-stamp: drop board reset workaround
  Blackfin: pr1: new board port

Acked-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This patch allows a board configuration file to provide default bus
and chip-selects for SPI flash so that first argument to the 'sf' command
is optional.

On boards that use the mxc_spi driver and a GPIO for chip select, this allows
a much simpler command line:
	U-Boot> sf probe
instead of
	U-Boot> sf probe 0x5300

Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Every board currently defines this to the same value, so just default
to that to avoid having to make everyone do the same thing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

pata_bfin.c: In function 'bfin_ata_identify':
pata_bfin.c:887:2: warning: format '%x' expects type 'unsigned int',
	but argument 2 has type 'lbaint_t'

Signed-off-by: Mike Frysinger <vapier@gentoo.org>