Add new infrastructure for implementing ethtool private flags using the
existing pf->flags bitmap to store them, and add the link-down-on-close
ethtool private flag to optionally bring down the PHY link when the
interface is administratively downed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.

In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 2fd527b7 ("net: ndo_bridge_setlink: Add extack") added a new
parameter "extack" to ice_bridge_setlink but this parameter isn't used
by the function. This results in a warning: unused parameter ‘extack’
[-Wunused-parameter]. Fix that by adding an "__always_unused" qualifier.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.

See commit 13a8cd19 ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.

Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).

To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.

Following patches will use the new argument in the bridge driver.

Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In code comments, use Tx|Rx instead of tx|rx

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1. Fix several cases of double spacing
2. Fix typos
3. Capitalize abbreviations

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up number of formatting issues and a comment that could use
clarification.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch includes below changes to resolve the issue of ETS bandwidth
shaping to work.

1. Allocation of Tx queues is accounted for based on the enabled TC's
   in ice_vsi_setup_q_map() and enabled the Tx queues on those TC's via
   ice_vsi_cfg_txqs()

2. Get the mapped netdev TC # for the user priority and set the priority
   to TC mapping for the VSI.

Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_dis_vsi() performs an rtnl_lock() if it detects a netdev that is
running on the VSI. In cases where the RTNL lock has already been
acquired, a deadlock results. Add a boolean to pass to ice_dis_vsi to
tell it if the RTNL lock is already held.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are setting the guar_num_vsi to equal to ICE_MAX_VSI
which is the device limit of 768. This is incorrect and could have
unintended consequences. To fix this use the valid_function's 8-bit
bitmap returned from discovering device capabilities to determine the
guar_num_vsi per function. guar_num_vsi value is then passed on to
pf->num_alloc_vsi.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the debug print in ice_tx_timeout is printing useless and
duplicate values. First, head is being assigned to tx_ring->next_to_clean
and we are printing both of those values, but naming them HWB and NTC
respectively. Also, reading tail always returns 0 so remove that as well.

Instead of assigning the SW head (NTC) read to head, use the actual head
register and change the debug print to note that this is HW_HEAD. Also
reduce the scope of a couple variables.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.

Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.

Tx HW tail write condition:
	if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
		writel(sw_tail, tx_ring->tail);

An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.

In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.

In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.

The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.

This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.

This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:

ICE_CACHE_LINE_BYTES		64
ICE_DESCS_PER_CACHE_LINE	(ICE_CACHE_LINE_BYTES / \
				 sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC		1
ICE_DESCS_FOR_SKB_DATA_PTR	1

The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.

Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The remove path does not currently check to see if a
reset is in progress before proceeding.  This can cause
a resource collision resulting in various types of errors.

Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.

For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Basically remove references to C810 and use E810C (from the branding
string) instead.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update version string to 0.7.2-k

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The ice_ena/dis_vsi should have a single differentiating
factor to determine if the netdev_ops call is used or a
direct call to ice_vsi_open/close.  This is if the netif is
running or not.  If netif is running, use ndo_open/ndo_close.
Else, use ice_vsi_open/ice_vsi_close.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the existing malicious driver operation detection
logic to cover malicious operations by the VF driver as well.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When PF gets a link status change event, notify the VFs of the same.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

virtchnl is a protocol/interface specification that allows the Intel
"Adaptive Virtual Function (AVF)" driver (iavf.ko) to work with more than
one physical function driver. The AVF driver sends "virtchnl commands"
(control plane only) to the PF driver over mailbox queues and the PF driver
executes these commands and returns a result to the VF, again over mailbox.

This patch adds AVF support for the ice PF driver by implementing the
following virtchnl commands:

VIRTCHNL_OP_VERSION
VIRTCHNL_OP_GET_VF_RESOURCES
VIRTCHNL_OP_RESET_VF
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_REQUEST_QUEUES
VIRTCHNL_OP_CONFIG_IRQ_MAP
VIRTCHNL_OP_CONFIG_RSS_KEY
VIRTCHNL_OP_CONFIG_RSS_LUT
VIRTCHNL_OP_GET_STATS
VIRTCHNL_OP_ADD_VLAN
VIRTCHNL_OP_DEL_VLAN
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements handlers for the following NDO operations:

.ndo_set_vf_spoofchk
.ndo_set_vf_mac
.ndo_get_vf_config
.ndo_set_vf_trust
.ndo_set_vf_vlan
.ndo_set_vf_link_state

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.

Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements parts of ice_sriov_configure and VF reset flow.

To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.

VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.

Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.

This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:

1. Currently we are using multiple members to store the interrupt
   granularity (itr_gran_25/50/100/200). This is not necessary because
   we can query the device to determine what the interrupt granularity
   should be set to, done by a new function ice_get_itr_intrl_gran.

2. Added intrl to ice_q_vector structure to support interrupt rate
   limiting.

3. Added the function ice_intrl_usecs_to_reg for converting to a value
   in usecs that the device understands.

4. Added call to write to the GLINT_RATE register. Disable intrl by
   default for now.

5. Changed rx/tx_itr_setting to itr_setting because having both seems
   redundant because a ring is either Tx or Rx.

6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.

Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.

Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.

Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.

Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.

To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.

Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.

Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.

To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.

In commit 0f9d5027 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, there is no bit, or set of bits, that protect the entirety
of the reset path.

If the reset is originated by the driver, then the relevant
one of the following bits will be set when the reset is scheduled:
__ICE_PFR_REQ
__ICE_CORER_REQ
__ICE_GLOBR_REQ
This bit will not be cleared until after the rebuild has completed.

If the reset is originated by the FW, then the first the driver knows of
it will be the reception of the OICR interrupt.  The __ICE_RESET_OICR_RECV
bit will be set in the interrupt handler.  This will also be the indicator
in a SW originated reset that we have completed the pre-OICR tasks and
have informed the FW that a reset was requested.

To utilize these bits, change the function:
ice_is_reset_recovery_pending()
	to be:
ice_is_reset_in_progress()

The new function will check all of the above bits in the pf->state and
will return a true if one or more of these bits are set.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch completes the code move out of ice_main.c

The following top level functions and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup
ice_vsi_cfg_tc

The following functions were made static again:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
void ice_vsi_map_rings_to_vectors
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_alloc_arrays

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs

The following functions were made static again:
ice_vsi_free_arrays
ice_vsi_clear_rings

Also, in this patch, the netdev and NAPI registration logic was de-coupled
from the VSI creation logic (ice_vsi_setup) as for SR-IOV, while we want to
create VF VSIs using ice_vsi_setup, we don't want to create netdevs.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>