After stress test, I found some of kzm9g board occures memory failure.
This patch adust SDRAM setting.
- Enlarge drivability on both SDRAM controller and SDRAM itself
- Raise core voltage

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

The following features are supported:
 * 128 MB DDR1 SDRAM
 * DUART
 * SD/MMC Card Socket

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

This adds a default environment with support for MMC booting.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

Add support for the MMC attached to SSP1.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 SSP register layout differs from MX28 in certain bits,
adjust the register layout accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 has less channels for the APBH DMA, sligtly different register
layout and some bits in those registers are placed differently. Reflect
this in the driver. This patch fixes MMC/DMA issue on MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

It is useful to be able to try a range of
possible phy addresses to connect.

Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Having only one call to fec_probe will ease the changing of its
parameters.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.

This also fixes MX28 fec_mii_setspeed use on secondary ethernet port

This was found by inspection of the code and should be
checked on real hardware.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Using the __weak annotation can make the code cleaner.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

Since this structure is not i.MX5x specific, remove the '5x' to make it more
generic.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h
to store the mmc partition, but in order for it to have effect we should place
it into 'mmcpart' variable.

Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

The USB host interface is routed to plug USB1/J30 on the mother board.

Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>

The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.

The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile

.gitignore was updated to ignore .cfgtmp files.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

The MX23 has different handling of the SSP clock and GPMI NAND clock sources,
add necessary quirks into the clock code to properly handle these.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Set Write Protection GPIO as input.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch adds support for MX23-based Olinuxino board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Replace use of ttyAM0 with ttyAMA0 as default serial console.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

The memory init is slightly different on MX23, thus split the memory
init for mx23 and mx28 into different functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 can only use two SSP ports.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

For i.MX23 we need to pass imx23 as elftosb param.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

This adds the boot mode support for i.MX23 processors.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Add information to identify i.MX23 chips and its known revisions.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Disable SSP2 and SSP3 ports on MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Add register definitions for the i.MX23 power control block and
clock control block. These are essential for the basic bootstrap
of the i.MX23. Also, properly include them in imx-regs.h .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>